Cardbus problem [SOLVED]

[Francisco Alves Cabrita]

> > In message: <1082226317.834.12.camel at zarcon.homeunix.net>
> >             Francisco Alves Cabrita <francisco at nortenet.pt> writes:
> > : hello
> > : i'm running (i386)5-CURRENT and in this "nightly" buildwold ,, my
> > : cardbus (ethernet pcmcia ovislink chipset rl) didnt get enabled""
> > : 
> > : 
> > : this was the message during boot:
> > : 
> > : cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0
> > : cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0
> > : cardbus0: <CardBus bus> on cbb0
> > : pccard0: <16-bit PCCard bus> on cbb0
> > : cbb0: bad Vcc request. ctrl=0xf000ef08, status=0xf000e2c3
> > : cbb_power: 0V
> > : cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0
> > : cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x1000
> > : cardbus1: <CardBus bus> on cbb1
> > : pccard1: <16-bit PCCard bus> on cbb1
> > : cbb1: bad Vcc request. ctrl=0x7720700, status=0x76f076c
> > : cbb_power: 0V
> > : 
> > : can some one give a tip !!! 
> > 
> > Please submit an older, working dmesg.  I think I know what's going
> > on, but w/o that, I can't be sure.
> > 
> > Since the cbb is on pci0, I think that you might have an non-ACPI
> > system.  Especially since the ToPIC95B is a relatively old chip.  My
> > guess is that this is a 100-166MHz Pentium system.
> > 
> > Warner
> 
> Hellow Warner, thank for you response.
> 
> Yes, you are almost right, is not an 100-166 Pentium , but and Toshiba
> (4300 series) Laptop 600Mhz with ACPI disabled for performence reasons,
> but here goes the boot message when was working:
> 
> cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0
> cardbus0: <CardBus bus> on cbb0
> pccard0: <16-bit PCCard bus> on cbb0
> cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0
> cardbus1: <CardBus bus> on cbb1
> pccard1: <16-bit PCCard bus> on cbb1
> 
> and the result:
> 
> rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem
> 0x88002000-0x880021ff irq 11 at device 0.0 on cardbus1
> miibus0: <MII bus> on rl0
> rlphy0: <RealTek internal media interface> on miibus0
> rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl0: Ethernet address: 00:10:60:75:66:fc
> rl0: [GIANT-LOCKED]
> 
> since I installed 5.X here, i disabled the ACPI module, and didnt have
> any hardware problems until now, but i will tunr it on to see what
> appen.
> 
yep, as you said,, I enabled acpi module under loader.conf and it's
working fine.

Thanks Warner