cardbus problems
Francisco Alves Cabrita
francisco at nortenet.pt
Sun Apr 18 11:37:32 PDT 2004
> In message: <1082226317.834.12.camel at zarcon.homeunix.net>
> Francisco Alves Cabrita <francisco at nortenet.pt> writes:
> : hello
> : i'm running (i386)5-CURRENT and in this "nightly" buildwold ,, my
> : cardbus (ethernet pcmcia ovislink chipset rl) didnt get enabled""
> :
> :
> : this was the message during boot:
> :
> : cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0
> : cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0
> : cardbus0: <CardBus bus> on cbb0
> : pccard0: <16-bit PCCard bus> on cbb0
> : cbb0: bad Vcc request. ctrl=0xf000ef08, status=0xf000e2c3
> : cbb_power: 0V
> : cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0
> : cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x1000
> : cardbus1: <CardBus bus> on cbb1
> : pccard1: <16-bit PCCard bus> on cbb1
> : cbb1: bad Vcc request. ctrl=0x7720700, status=0x76f076c
> : cbb_power: 0V
> :
> : can some one give a tip !!!
>
> Please submit an older, working dmesg. I think I know what's going
> on, but w/o that, I can't be sure.
>
> Since the cbb is on pci0, I think that you might have an non-ACPI
> system. Especially since the ToPIC95B is a relatively old chip. My
> guess is that this is a 100-166MHz Pentium system.
>
> Warner
Hellow Warner, thank for you response.
Yes, you are almost right, is not an 100-166 Pentium , but and Toshiba
(4300 series) Laptop 600Mhz with ACPI disabled for performence reasons,
but here goes the boot message when was working:
cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
and the result:
rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem
0x88002000-0x880021ff irq 11 at device 0.0 on cardbus1
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:10:60:75:66:fc
rl0: [GIANT-LOCKED]
since I installed 5.X here, i disabled the ACPI module, and didnt have
any hardware problems until now, but i will tunr it on to see what
appen.
[] thanks
Francisco
More information about the freebsd-current
mailing list