bge on FreeBSD 5.2 Current SMP (bge0: watchdog timeout -- resetting)
Peter Wood
peter at alastria.net
Fri Apr 2 15:48:01 PST 2004
Good Morning,
I've had this problem for a while now, however due to educational constraints
I've been unable to look at it for a while.
I have several gigabit lan cards on a gig switch, these cards have a Broadcom
chipset and are sold by Netgear as GA302T (if I recall correctly). The card
works perfectly under Windows.
After sending a small ammount of data through them they simply stop responding
to the network. A couple of seconds later they report to the console "bge0:
watchdog timeout -- resetting", only way to get it to talk again is to reboot.
These cards worked under 4.7 a while back, but I'd imagin it's more to do with
interrupt and other things then that. The motherboard is a Tyan Tiger MPX.
The motherboard nor network cards arn't exactly great by themselves, so I'm
suprised I've not had more issues. For example, I can't use the last PCI slot
on the board under 5.2 as it just seems to fail completely.
If anyone could help me track this problem down and to solve it, I'd greatly
apreciate it. Attached are a dmesg after "boot -v" and pciconf.
Kind regards and thanks in advance,
Peter.
[xenon:~]$ dmesg
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory = 2146959360 (2047 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009cfff, 638976 bytes (156 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x000000007dac9fff, 2095714304 bytes (511649 pages)
0x000000007ff00000 - 0x000000007ff77fff, 491520 bytes (120 pages)
avail memory = 2095464448 (1998 MB)
Table 'FACP' at 0x7fefef2e
Table 'APIC' at 0x7fefefa2
MADT: Found table at 0x7fefefa2
MP Configuration Table version 1.4 found at 0xc009fd70
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 1 ACPI ID 0: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
ACPI APIC Table: <PTLTD APIC >
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 1
cpu1 (AP): APIC ID: 0
bios32: Found BIOS32 Service Directory header at 0xc00f70d0
bios32: Entry = 0xfd6b0 (c00fd6b0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd6b0+0x120
pnpbios: Found PnP BIOS data at 0xc00f7130
pnpbios: Entry = f0000:9aad Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: intpin 0 -> ExtINT (edge, activehi)
ioapic0: intpin 1 -> irq 1 (edge, activehi)
ioapic0: intpin 2 -> irq 2 (edge, activehi)
ioapic0: intpin 3 -> irq 3 (edge, activehi)
ioapic0: intpin 4 -> irq 4 (edge, activehi)
ioapic0: intpin 5 -> irq 5 (edge, activehi)
ioapic0: intpin 6 -> irq 6 (edge, activehi)
ioapic0: intpin 7 -> irq 7 (edge, activehi)
ioapic0: intpin 8 -> irq 8 (edge, activehi)
ioapic0: intpin 9 -> irq 9 (edge, activehi)
ioapic0: intpin 10 -> irq 10 (edge, activehi)
ioapic0: intpin 11 -> irq 11 (edge, activehi)
ioapic0: intpin 12 -> irq 12 (edge, activehi)
ioapic0: intpin 13 -> irq 13 (edge, activehi)
ioapic0: intpin 14 -> irq 14 (edge, activehi)
ioapic0: intpin 15 -> irq 15 (edge, activehi)
ioapic0: intpin 16 -> irq 16 (level, activelo)
ioapic0: intpin 17 -> irq 17 (level, activelo)
ioapic0: intpin 18 -> irq 18 (level, activelo)
ioapic0: intpin 19 -> irq 19 (level, activelo)
ioapic0: intpin 20 -> irq 20 (level, activelo)
ioapic0: intpin 21 -> irq 21 (level, activelo)
ioapic0: intpin 22 -> irq 22 (level, activelo)
ioapic0: intpin 23 -> irq 23 (level, activelo)
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 polarity: active-hi
ioapic0: intpin 2 trigger: edge
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: active-hi
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: active-hi
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x01000000 VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
cpu0 on motherboard
cpu1 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT> on motherboard
acpi0: [GIANT-LOCKED]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000818
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=700c1022)
pcibios: BIOS version 2.10
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 3
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu1: <CPU> port 0x530-0x537 on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x8080-0x80ff,0x8000-0x807f,0xcf8-0xcff
iomem 0xd8000-0xdbfff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f4000000, size 26, enabled
map[14]: type 3, range 32, base f2100000, size 12, enabled
map[18]: type 4, range 32, base 00001020, size 2, port disabled
found-> vendor=0x1022, dev=0x700c, revid=0x11
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x700d, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x63 (2970 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x7440, revid=0x05
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000f000, size 4, enabled
found-> vendor=0x1022, dev=0x7441, revid=0x04
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x7443, revid=0x03
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x16 (660 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 00001038, size 3, enabled
map[14]: type 4, range 32, base 00001030, size 2, enabled
map[18]: type 4, range 32, base 00001028, size 3, enabled
map[1c]: type 4, range 32, base 00001024, size 2, enabled
map[20]: type 4, range 32, base 00001010, size 4, enabled
map[24]: type 1, range 32, base f0000000, size 14, enabled
pcib0: matched entry for 0.8.INTA (src )
pcib0: device is hardwired to IRQ 20
found-> vendor=0x105a, dev=0x4d68, revid=0x02
bus=0, slot=8, func=0
class=01-80-85, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0430, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=20
powerspec 1 supports D0 D1 D3 current D0
found-> vendor=0x1044, dev=0xa500, revid=0x02
bus=0, slot=9, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0006, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base f8000000, size 26, enabled
pcib0: matched entry for 0.9.INTA (src )
pcib0: device is hardwired to IRQ 21
found-> vendor=0x1044, dev=0xa501, revid=0x02
bus=0, slot=9, func=1
class=0e-00-01, hdrtype=0x00, mfdev=1
cmdreg=0x0016, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x01 (250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=21
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1022, dev=0x7448, revid=0x05
bus=0, slot=16, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0017, statreg=0x2220, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
agp0: <AMD 762 host to AGP bridge> port 0x1020-0x1023 mem
0xf2100000-0xf2100fff,0xf4000000-0xf7ffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 64M
agp0: gatt -> ag_pdir 0x28c000
agp0: allocating GATT for 16384 AGP page entries
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xf1000000-0xf1ffffff
pcib1: prefetched decode 0xfc000000-0xfcffffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base f1000000, size 24, enabled
map[14]: type 3, range 32, base fc000000, size 24, enabled
pcib1: matched entry for 1.5.INTA (src )
pcib1: device is hardwired to IRQ 18
found-> vendor=0x10de, dev=0x0020, revid=0x04
bus=1, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=18
powerspec 1 supports D0 D3 current D0
pci1: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 768 UDMA100 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=10 ostat1=01
ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb
ata1-slave: stat=0x01 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 mask=03 stat0=10 stat1=01
devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
atapci1: <Promise PDC20268 UDMA100 controller> port
0x1010-0x101f,0x1024-0x1027,0x1028-0x102f,0x1030-0x1033,0x1038-0x103f mem
0xf0000000-0xf0003fff irq 20 at device 8.0 on pci0
atapci1: [MPSAFE]
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: at 0x1038 on atapci1
ata2: [MPSAFE]
ata3: reset tp1 mask=03 ostat0=50 ostat1=00
ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata3-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata3: at 0x1028 on atapci1
ata3: [MPSAFE]
pcib2: <PCI-PCI bridge> at device 9.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0x100000-0xfffff
pcib2: prefetched decode 0x100000-0xfffff
pci2: <PCI bus> on pcib2
pci2: physical bus=2
asr0: <Adaptec Caching SCSI RAID> mem 0xf8000000-0xfbffffff irq 21 at device
9.1 on pci0
asr0: major=154
asr0: [GIANT-LOCKED]
asr0: ADAPTEC 2400A FW Rev. 370L, 4 channel, 256 CCBs, Protocol I2O
pcib3: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0x2000-0x2fff
pcib3: memory decode 0xf2000000-0xf20fffff
pcib3: prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
map[10]: type 1, range 32, base f2010000, size 12, enabled
pcib3: matched entry for 3.0.INTD (src )
pcib3: device is hardwired to IRQ 19
found-> vendor=0x1022, dev=0x7449, revid=0x07
bus=3, slot=0, func=0
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=d, irq=19
map[10]: type 4, range 32, base 00002000, size 8, enabled
map[14]: type 1, range 32, base f2011000, size 12, enabled
pcib3: matched entry for 3.4.INTA (src )
pcib3: device is hardwired to IRQ 16
found-> vendor=0x9004, dev=0x5078, revid=0x03
bus=3, slot=4, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=16
powerspec 1 supports D0 D3 current D0
map[10]: type 4, range 32, base 00002480, size 6, enabled
pcib3: matched entry for 3.5.INTA (src )
pcib3: device is hardwired to IRQ 17
found-> vendor=0x1274, dev=0x5000, revid=0x00
bus=3, slot=5, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0400, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0c (3000 ns), maxlat=0x80 (32000 ns)
intpin=a, irq=17
map[10]: type 1, range 64, base f2000000, size 16, enabled
pcib3: matched entry for 3.6.INTA (src )
pcib3: device is hardwired to IRQ 18
found-> vendor=0x173b, dev=0x03ea, revid=0x15
bus=3, slot=6, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0016, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=18
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type 4, range 32, base 00002400, size 7, enabled
map[14]: type 1, range 32, base f2012000, size 7, enabled
pcib3: matched entry for 3.8.INTA (src )
pcib3: device is hardwired to IRQ 19
found-> vendor=0x10b7, dev=0x9200, revid=0x78
bus=3, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0210, cachelnsz=16 (dwords)
lattimer=0x50 (2400 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D2 D3 current D0
pci3: <serial bus, USB> at device 0.0 (no driver attached)
ahc0: <Adaptec 2902/04/10/15/20C/30C SCSI adapter> port 0x2000-0x20ff mem
0xf2011000-0xf2011fff irq 16 at device 4.0 on pci3
ahc0: Defaulting to MEMIO off
pcib3: device ahc0 requested decoded I/O range 0x2000-0x20ff
ahc0: No SEEPROM available.
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
ahc0: Downloading Sequencer Program... 457 instructions downloaded
ahc0: Features 0x10100, Bugs 0x35, Flags 0x8401f44
ahc0: [GIANT-LOCKED]
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
pcm0: <AudioPCI ES1370> port 0x2480-0x24bf irq 17 at device 5.0 on pci3
pcib3: device pcm0 requested decoded I/O range 0x2480-0x24bf
pcm0: [GIANT-LOCKED]
pcm0: sndbuf_setmap 2e3000, 1000; 0xc740f000 -> 2e3000
pcm0: sndbuf_setmap 7d672000, 1000; 0xc743e000 -> 7d672000
bge0: <Altima AC9100 Gigabit Ethernet, ASIC rev. 0x105> mem
0xf2000000-0xf200ffff irq 18 at device 6.0 on pci3
pcib3: device bge0 requested decoded memory range 0xf2000000-0xf200ffff
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: bpf attached
bge0: Ethernet address: 00:09:5b:1b:90:91
bge0: [GIANT-LOCKED]
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x2400-0x247f mem
0xf2012000-0xf201207f irq 19 at device 8.0 on pci3
pcib3: device xl0 requested decoded memory range 0xf2012000-0xf201207f
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus1: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: OUI 0x00105a, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:e0:81:21:83:70
xl0: [GIANT-LOCKED]
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0047
psm0: failed to reset the aux device.
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
sio0: irq maps: 0xe001 0xe011 0xe001 0xe001
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: irq maps: 0xe001 0xe009 0xe001 0xe001
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem
0xe0000-0xe3fff,0xca800-0xd07ff,0xc8800-0xca7ff,0xc8000-0xc87ff,0xc0000-0xc7fff
on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1666735157 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x44 cable=80pin
ata0-master: setting PIO4 on AMD 768 chip
ata0-master: setting UDMA66 on AMD 768 chip
acd0: <Pioneer DVD-ROM ATAPIModel DVD-117 0107/E1.07> DVDROM drive at ata0 as
master
acd0: read 6894KB/s (6894KB/s), 256KB buffer, UDMA66
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata1-slave: FAILURE - ATAPI_IDENTIFY no interrupt
ata1-slave: FAILURE - ATAPI_IDENTIFY status=1<ERROR> error=1<ILLEGAL_LENGTH>
LBA=0
ata1-slave: FAILURE - ATAPI_IDENTIFY no interrupt
ata1-slave: FAILURE - ATAPI_IDENTIFY status=1<ERROR> error=1<ILLEGAL_LENGTH>
LBA=0
ata1-master: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
ata1-master: setting PIO4 on AMD 768 chip
ata1-master: setting WDMA2 on AMD 768 chip
ast0: <Seagate STT20000A/8A51> tape drive at ata1 as master
ast0: 1000KB/s, transfer limit 108 blks, 324KB buffer, WDMA2
ast0: Medium: none, readonly, qfa, ecc, 512b
ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata2-master: setting PIO4 on Promise PDC20268 chip
ata2-master: setting UDMA100 on Promise PDC20268 chip
ad4: <WDC WD1200JB-00DUA3/75.13B75> ATA-6 disk at ata2-master
ad4: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad4
ata3-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata3-master: setting PIO4 on Promise PDC20268 chip
ata3-master: setting UDMA100 on Promise PDC20268 chip
ad6: <IC35L060AVER07-0/ER6OA46A> ATA-5 disk at ata3-master
ad6: 58644MB (120103200 sectors), 119150 C, 16 H, 63 S, 512 B
ad6: 16 secs/int, 1 depth queue, UDMA100
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:234436482
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 32256 length 120031478784 end 120031511039
GEOM: new disk ad6
GEOM: Configure ad4s1a, start 0 length 536870912 end 536870911
GEOM: Configure ad4s1b, start 536870912 length 2147483648 end 2684354559
GEOM: Configure ad4s1c, start 0 length 120031478784 end 120031478783
GEOM: Configure ad4s1d, start 2684354560 length 536870912 end 3221225471
GEOM: Configure ad4s1e, start 3221225472 length 536870912 end 3758096383
GEOM: Configure ad4s1f, start 3758096384 length 116273382400 end 120031478783
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/11/63 s:63 l:120101877
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad6s1, start 32256 length 61492161024 end 61492193279
GEOM: Configure ad6s1c, start 0 length 61492161024 end 61492161023
GEOM: Configure ad6s1d, start 0 length 61492161024 end 61492161023
(ahc0:A:4:0): Received SDTR period 19, offset f
Filtered to period 0, offset 0
(ahc0:A:4:0): Target Initiated SDTR
(ahc0:A:4:0): Sending SDTR period 45, offset 0
(probe30:ahc0:0:2:0): error 22
(probe30:ahc0:0:2:0): Unretryable Error
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
ahc0: target 4 synchronous at 10.0MHz, offset = 0xf
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
ahc0: target 2 synchronous at 10.0MHz, offset = 0xf
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
pass0 at asr0 bus 0 target 0 lun 0
pass0: <ADAPTEC RAID-5 370L> Fixed Direct Access SCSI-2 device
pass0: Serial Number +
pass0: Tagged Queueing Enabled
pass1 at ahc0 bus 0 target 2 lun 0
pass1: <YAMAHA CRW8824S 1.00> Removable CD-ROM SCSI-2 device
pass1: 10.000MB/s transfers (10.000MHz, offset 15)
pass2 at ahc0 bus 0 target 4 lun 0
pass2: <Quantum DLT4000 CPQ DRV D473> Removable Sequential Access SCSI-2
device
pass2: Serial Number CX922M1222
pass2: 10.000MB/s transfers (10.000MHz, offset 15)
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <Quantum DLT4000 CPQ DRV D473> Removable Sequential Access SCSI-2 device
sa0: Serial Number CX922M1222
sa0: 10.000MB/s transfers (10.000MHz, offset 15)
da0 at asr0 bus 0 target 0 lun 0
da0: <ADAPTEC RAID-5 370L> Fixed Direct Access SCSI-2 device
da0: Serial Number +
da0: Tagged Queueing Enabled
da0: 343419MB (703322112 512 byte sectors: 255H 63S/T 43779C)
(ahc0:A:2:0): Sending SDTR period 19, offset f
GEOM: new disk cd0
GEOM: new disk da0
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 3 (IRQ 3) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 6 (IRQ 6) to cluster 0
ioapic0: routing intpin 7 (IRQ 7) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 13 (IRQ 13) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic0: routing intpin 16 (IRQ 16) to cluster 0
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
ioapic0: routing intpin 20 (IRQ 20) to cluster 0
ioapic0: routing intpin 21 (IRQ 21) to cluster 0
(ahc0:A:2:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
cd0 at ahc0 bus 0 target 2 lun 0
cd0: <YAMAHA CRW8824S 1.00> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray
closed
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:703309572
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 32256 length 360094500864 end 360094533119
GEOM: Configure da0s1c, start 0 length 360094500864 end 360094500863
GEOM: Configure da0s1d, start 0 length 360094500864 end 360094500863
Mounting root from ufs:/dev/ad4s1a
start_init: trying /sbin/init
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 120 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 180 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 240 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 300 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 360 bytes
[xenon:~]$ pciconf -l -v
agp0 at pci0:0:0: class=0x060000 card=0x00000000 chip=0x700c1022 rev=0x11
hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = 'AMD-762 CPU to PCI Bridge (SMP chipset)'
class = bridge
subclass = HOST-PCI
pcib1 at pci0:1:0: class=0x060400 card=0x00000000 chip=0x700d1022 rev=0x00
hdr=0x01
vendor = 'Advanced Micro Devices (AMD)'
device = 'AMD-762 CPU to PCI Bridge (AGP 4x)'
class = bridge
subclass = PCI-PCI
isab0 at pci0:7:0: class=0x060100 card=0x00000000 chip=0x74401022 rev=0x05
hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = 'AMD-768 PCI to ISA/LPC Bridge'
class = bridge
subclass = PCI-ISA
atapci0 at pci0:7:1: class=0x01018a card=0x74411022 chip=0x74411022
rev=0x04 hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = 'AMD-768 EIDE Controller'
class = mass storage
subclass = ATA
none0 at pci0:7:3: class=0x068000 card=0x74431022 chip=0x74431022 rev=0x03
hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = 'AMD-768 System Management'
class = bridge
subclass = PCI-unknown
atapci1 at pci0:8:0: class=0x018085 card=0x4d68105a chip=0x4d68105a
rev=0x02 hdr=0x00
vendor = 'Promise Technology Inc'
device = 'PDC20268 Ultra100 TX2 EIDE Controller'
class = mass storage
pcib2 at pci0:9:0: class=0x060400 card=0x00000068 chip=0xa5001044 rev=0x02
hdr=0x01
vendor = 'Adaptec (Formerly: Distributed Processing Technology (DPT))'
device = 'PCI Bridge'
class = bridge
subclass = PCI-PCI
asr0 at pci0:9:1: class=0x0e0001 card=0xc05a1044 chip=0xa5011044 rev=0x02
hdr=0x00
vendor = 'Adaptec (Formerly: Distributed Processing Technology (DPT))'
device = 'I2O SmartRAID V Controller'
pcib3 at pci0:16:0: class=0x060400 card=0x00000000 chip=0x74481022
rev=0x05 hdr=0x01
vendor = 'Advanced Micro Devices (AMD)'
device = 'AMD-768 PCI Bridge'
class = bridge
subclass = PCI-PCI
none1 at pci1:5:0: class=0x030000 card=0x10151102 chip=0x002010de rev=0x04
hdr=0x00
vendor = 'NVIDIA Corporation'
device = 'Riva TNT GUI+3D Accelerator [NV4]'
class = display
subclass = VGA
none2 at pci3:0:0: class=0x0c0310 card=0x00000000 chip=0x74491022 rev=0x07
hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = 'AMD-768 USB Controller'
class = serial bus
subclass = USB
ahc0 at pci3:4:0: class=0x010000 card=0x78509004 chip=0x50789004 rev=0x03
hdr=0x00
vendor = 'Adaptec Inc'
device = 'AVA-2902I/E,AVA-2904,AVA-2910 (AIC-7850P) Fast/Wide SCSI II'
class = mass storage
subclass = SCSI
pcm0 at pci3:5:0: class=0x040100 card=0x4c4c4942 chip=0x50001274 rev=0x00
hdr=0x00
vendor = 'Creative (Was: Ensoniq)'
device = 'ES1370 AudioPCI'
class = multimedia
subclass = audio
bge0 at pci3:6:0: class=0x020000 card=0x302a1385 chip=0x03ea173b rev=0x15
hdr=0x00
vendor = 'Altima Communications Inc'
class = network
subclass = ethernet
xl0 at pci3:8:0: class=0x020000 card=0x246610f1 chip=0x920010b7 rev=0x78
hdr=0x00
vendor = '3COM Corp, Networking Division'
device = '3C905C-TX Fast EtherLink for PC Management NIC'
class = network
subclass = ethernet
--
Peter Wood <peter at alastria.net> :: Tel +44 7974 799440
More information about the freebsd-current
mailing list