Hang on boot after SETFEATURES recovered from missing interrupt
message
CJ van den Berg
freebsd at vdbonline.com
Thu Nov 13 11:37:02 PST 2003
Hi,
I'm having trouble booting today's current. The kernel hangs after various
messages such as:
ad0: WARNING - SETFEATURES recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - SET_MULTI recovered from missing interrupt
I've tried disabling acpi and ata_dma with no effect. I can still break into
the debugger, but as it is not a panic I don't know what help that is.
Last running kernel is from Fri Oct 3 00:28:37 CEST 2003 which I think is
post atang, but I'm not sure.
Any tips are welcome. Full log of boot -v follows.
-CJ
Console: serial port
BIOS drive A: is disk0
BIOS drive C: is disk1
BIOS drive D: is disk2
BIOS 639kB/228288kB available memory
FreeBSD/i386 bootstrap loader, Revision 1.1
(cjv at dent.vdbonline.com, Wed Jun 25 00:18:04 CEST 2003)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x4c0898 data=0x79fec+0x64c10 syms=[0x4+0x5a4f0+0x4
+0x6eb3a]
/boot/kernel/vesa.ko text=0x39d8 data=0x2a0+0x27c syms=[0x4+0x850+0x4+0x709]
/boot/kernel/snd_pcm.ko text=0x14cb8 data=0x2288+0x10c4 syms=[0x4+0x2bc0+0x4
+0x30f0]
/boot/kernel/snd_emu10k1.ko text=0x4ffc data=0x61c+0x4 syms=[0x4+0xbe0+0x4
+0xc12]
Loading /boot/defaults/loader.conf
Hit [Enter] to boot immediately, or any other key for command prompt.
Type '?' for a list of commands, 'help' for more detailed help.
OK boot -v
SMAP type=01 base=0000000000000000 len=000000000009fc00
SMAP type=02 base=000000000009fc00 len=0000000000000400
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=02 base=00000000ffff0000 len=0000000000010000
SMAP type=01 base=0000000000100000 len=000000000def0000
SMAP type=03 base=000000000dff3000 len=000000000000d000
SMAP type=04 base=000000000dff0000 len=0000000000003000
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #0: Thu Nov 13 17:03:39 CET 2003
root at dent.vdbonline.com:/usr/obj/usr/src/sys/BEEBELBROX
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a97000.
Preloaded elf module "/boot/kernel/vesa.ko" at 0xc0a97200.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a972ac.
Preloaded elf module "/boot/kernel/snd_emu10k1.ko" at 0xc0a97358.
Calibrating clock(s) ... i8254 clock: 1193256 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 499781229 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (499.78-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x665 Stepping = 5
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 234815488 (223 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x000000000dbd9fff, 217780224 bytes (53169 pages)
avail memory = 218529792 (208 MB)
bios32: Found BIOS32 Service Directory header at 0xc00fafb0
bios32: Entry = 0xfb430 (c00fb430) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb460
pnpbios: Found PnP BIOS data at 0xc00fc000
pnpbios: Entry = f0000:c028 Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
VESA: information block
56 45 53 41 00 03 00 01 00 01 01 00 00 00 22 00
00 01 40 00 05 02 07 01 00 01 0e 01 00 01 17 01
00 01 00 01 01 01 02 01 03 01 04 01 05 01 06 01
07 01 08 01 09 01 0a 01 0b 01 0c 01 0e 01 0f 01
VESA: 33 mode(s) found
VESA: v3.0, 4096k memory, flags:0x1, mode table:0xc0a6ece2 (1000022)
VESA: NVidia
VESA: NVidia Riva TNT B1
acpi0: <AWARD AWRDACPI> on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80005810
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00fdf00
PCI-Only Interrupts: 5 9 10 11
Location Bus Device Pin Link IRQs
slot 1 0 15 A 0x60 3 4 5 7 9 10 11 12 14 15
slot 1 0 15 B 0x61 3 4 5 7 9 10 11 12 14 15
slot 1 0 15 C 0x62 3 4 5 7 9 10 11 12 14 15
slot 1 0 15 D 0x63 3 4 5 7 9 10 11 12 14 15
slot 2 0 13 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 2 0 13 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 2 0 13 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 2 0 13 D 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 A 0x62 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 B 0x63 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 C 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 0 11 D 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 0 9 A 0x63 3 4 5 7 9 10 11 12 14 15
slot 4 0 9 B 0x60 3 4 5 7 9 10 11 12 14 15
slot 4 0 9 C 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 0 9 D 0x62 3 4 5 7 9 10 11 12 14 15
slot 5 0 17 A 0x63 3 4 5 7 9 10 11 12 14 15
slot 5 0 17 B 0x60 3 4 5 7 9 10 11 12 14 15
slot 5 0 17 C 0x61 3 4 5 7 9 10 11 12 14 15
slot 5 0 17 D 0x62 3 4 5 7 9 10 11 12 14 15
embedded 0 7 A 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 7 B 0x61 3 4 5 7 9 10 11 12 14 15
embedded 0 7 C 0x62 3 4 5 7 9 10 11 12 14 15
embedded 0 7 D 0x63 3 4 5 7 9 10 11 12 14 15
embedded 0 1 A 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 1 B 0x61 3 4 5 7 9 10 11 12 14 15
embedded 0 1 C 0x62 3 4 5 7 9 10 11 12 14 15
embedded 0 1 D 0x63 3 4 5 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
ACPI timer looks BAD min = 2, max = 5, width = 3
ACPI timer looks BAD min = 2, max = 16777213, width = 16777211
ACPI timer looks BAD min = 2, max = 5, width = 3
ACPI timer looks BAD min = 2, max = 5, width = 3
ACPI timer looks BAD min = 1, max = 5, width = 4
ACPI timer looks BAD min = 1, max = 5, width = 4
ACPI timer looks BAD min = 2, max = 5, width = 3
ACPI timer looks BAD min = 2, max = 5, width = 3
ACPI timer looks BAD min = 2, max = 5, width = 3
ACPI timer looks BAD min = 1, max = 5, width = 4
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4000-0x4041,0xcf8-0xcff
on acpi0
---- initial configuration ------------------------
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.0
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.1
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.2
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.3
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.0
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.1
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.2
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.3
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.0
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.1
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.2
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.3
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.0
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.1
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.2
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.3
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.0
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.1
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.2
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.3
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.0
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.1
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.2
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.3
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.0
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.1
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.2
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.3
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.0
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.1
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.2
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.15.3
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.0
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.1
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.2
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.13.3
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.0
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.1
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.2
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.11.3
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.0
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.1
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.2
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.9.3
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.0
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.1
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.2
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.17.3
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.0
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.1
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.2
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.7.3
\_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.0
\_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.1
\_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.2
\_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15]
low,level,sharable 0.1.3
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base e0000000, size 26, enabled
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x88 (34000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000f000, size 4, enabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000a000, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \_SB_.PCI0.ISA_.LNKD)
pcib0: slot 7 INTD is routed to irq 11
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
map[90]: type 4, range 32, base 00005000, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base ec000000, size 12, enabled
map[14]: type 4, range 32, base 0000a400, size 8, enabled
pcib0: matched entry for 0.9.INTA (source \_SB_.PCI0.ISA_.LNKD)
pcib0: slot 9 INTA is routed to irq 11
found-> vendor=0x1050, dev=0x6692, revid=0x01
bus=0, slot=9, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 4, range 32, base 0000a800, size 7, enabled
map[14]: type 1, range 32, base ec001000, size 7, enabled
pcib0: matched entry for 0.11.INTA (source \_SB_.PCI0.ISA_.LNKC)
pcib0: slot 11 INTA is routed to irq 9
found-> vendor=0x10b7, dev=0x9200, revid=0x74
bus=0, slot=11, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base e9000000, size 24, enabled
pcib0: matched entry for 0.13.INTA (source \_SB_.PCI0.ISA_.LNKB)
pcib0: slot 13 INTA is routed to irq 5
found-> vendor=0x14f1, dev=0x8800, revid=0x03
bus=0, slot=13, func=0
class=04-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x14 (5000 ns), maxlat=0x37 (13750 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base ea000000, size 24, enabled
pcib0: matched entry for 0.13.INTA (source \_SB_.PCI0.ISA_.LNKB)
pcib0: slot 13 INTA is routed to irq 5
found-> vendor=0x14f1, dev=0x8811, revid=0x03
bus=0, slot=13, func=1
class=04-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0xff (63750 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000ac00, size 3, enabled
map[14]: type 4, range 32, base 0000b000, size 2, enabled
map[18]: type 4, range 32, base 0000b400, size 3, enabled
map[1c]: type 4, range 32, base 0000b800, size 2, enabled
map[20]: type 4, range 32, base 0000bc00, size 4, enabled
pcib0: matched entry for 0.15.INTA (source \_SB_.PCI0.ISA_.LNKA)
pcib0: slot 15 INTA is routed to irq 10
found-> vendor=0x1095, dev=0x0649, revid=0x02
bus=0, slot=15, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000c000, size 5, enabled
pcib0: matched entry for 0.17.INTA (source \_SB_.PCI0.ISA_.LNKD)
pcib0: slot 17 INTA is routed to irq 11
found-> vendor=0x1102, dev=0x0002, revid=0x04
bus=0, slot=17, func=0
class=04-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=11
powerspec 1 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000c400, size 3, enabled
found-> vendor=0x1102, dev=0x7002, revid=0x01
bus=0, slot=17, func=1
class=09-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D3 current D0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe0000000-0xe3ffffff
at device 0.0 on pci0
agp0: allocating GATT for aperture of size 64M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x9000-0x9fff
pcib1: memory decode 0xe4000000-0xe5ffffff
pcib1: prefetched decode 0xe6000000-0xe7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base e4000000, size 24, enabled
map[14]: type 3, range 32, base e6000000, size 25, enabled
pcib0: matched entry for 0.1.INTA (source \_SB_.PCI0.ISA_.LNKA)
pcib0: slot 1 INTA is routed to irq 10
pcib1: slot 0 INTA is routed to irq 10
found-> vendor=0x10de, dev=0x0029, revid=0x11
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=10
powerspec 1 supports D0 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0xf000-0xf00f at device 7.1 on
pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0: reset tp2 mask=03 stat0=00 stat1=00
devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1-master: stat=0x00 err=0x00 lsb=0x00 msb=0x00
ata1-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: reset tp2 mask=03 stat0=00 stat1=00 devices=0x0
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xa000-0xa01f irq 11
at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ulpt0: Hewlett-Packard DeskJet 3820, rev 1.10/1.00, addr 2, iclass 7/1
ulpt0: using bi-directional mode
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pci0: <network> at device 9.0 (no driver attached)
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xa800-0xa87f mem
0xec001000-0xec00107f irq 9 at device 11.0 on pci0
xl0: using memory mapped I/O
xl0: Ethernet address: 00:50:da:e2:8a:2d
xl0: media options word: a
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
pci0: <multimedia, video> at device 13.0 (no driver attached)
pci0: <multimedia> at device 13.1 (no driver attached)
atapci1: <CMD 649 UDMA100 controller> port
0xbc00-0xbc0f,0xb800-0xb803,0xb400-0xb407,0xb000-0xb003,0xac00-0xac07 irq
10 at device 15.0 on pci0
atapci1: [MPSAFE]
ata2: reset tp1 mask=03 ostat0=50 ostat1=50
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata2: at 0xac00 on atapci1
ata2: [MPSAFE]
ata3: reset tp1 mask=03 ostat0=7f ostat1=7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: reset tp2 mask=00 stat0=ff stat1=ff devices=0x0
ata3: at 0xb400 on atapci1
ata3: [MPSAFE]
pcm0: <Creative EMU10K1> port 0xc000-0xc01f irq 11 at device 17.0 on pci0
emu: setmap (d71e000, 800), nseg=1, error=0
emu: setmap (d81f000, 1000), nseg=1, error=0
pcm0: <TriTech TR28023 AC97 Codec (id = 0x54524103)>
pcm0: Codec features 6 bit master volume, no 3D Stereo Enhancement
emu: setmap (d801000, 1000), nseg=1, error=0
emu: setmap (d783000, 1000), nseg=1, error=0
emu: setmap (d55c000, 1000), nseg=1, error=0
emu: setmap (d31a000, 1000), nseg=1, error=0
pcm0: sndbuf_setmap d4d8000, 1000; 0xc2a24000 -> d4d8000
pcm0: sndbuf_setmap d696000, 1000; 0xc2a22000 -> d696000
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
sio0: irq maps: 0x801 0x811 0x801 0x801
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
sio1: irq maps: 0x801 0x809 0x801 0x801
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: using extended I/O port range
ppc0: SPP
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: not probed (disabled)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 1a 03 c8
psm: status 1a 03 c8
psm: status 1a 03 c8
psm: data c8 c6 51
psm: data e8 f2 30
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0-51, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:08, syncbits:08
unknown: not probed (disabled)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ex_isa_identify()
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xd1000-0xd37ff,0xd0000-0xd07ff,0xc0000-0xcffff
on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
fb: new array size 4
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x700ff
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 01 0f 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 499781229 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ata0-slave: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ata0-master: setting PIO4 on Intel PIIX4 chip
ata0-master: setting UDMA33 on Intel PIIX4 chip
ata0-slave: setting PIO4 on Intel PIIX4 chip
ata0-slave: setting WDMA2 on Intel PIIX4 chip
acd0: <TDK CDRW4800B/S7S4> CDRW drive at ata0 as master
acd0: read 8250KB/s (8250KB/s) write 172KB/s (8250KB/s), 2048KB buffer,
UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
acd1: <CREATIVEDVD-ROM DVD2240E 08/23/97/1.0A> DVDROM drive at ata0 as slave
acd1: read 4125KB/s (4125KB/s), 256KB buffer, WDMA2
acd1: Reads: CDR, CDRW, CDDA, DVDROM, packet
acd1: Writes:
acd1: Audio: play, 255 volume levels
acd1: Mechanism: ejectable tray, unlocked
acd1: Medium: no/blank disc
ata2-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata2-master: WARNING - SETFEATURES recovered from missing interrupt
ata2-master: setting PIO4 on CMD 649 chip
ata2-slave: WARNING - SETFEATURES recovered from missing interrupt
ata2-slave: setting PIO4 on CMD 649 chip
ad0: WARNING - SETFEATURES recovered from missing interrupt
ad0: WARNING - SETFEATURES recovered from missing interrupt
ad0: WARNING - SET_MULTI recovered from missing interrupt
GEOM: create disk ad0 dp=0xc2a9ae60
ad0: <IC35L020AVER07-0/ER2OA44A> ATA-5 disk at ata2-master
ad0: 19623MB (40188960 sectors), 39870 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, PIO4
GEOM: new disk ad0
ad0: WARNING - READ_MUL recovered from missing interrupt
ar: FreeBSD check1 failed
ad0: WARNING - READ_MUL recovered from missing interrupt
[0] f:00 typ:7 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:16771797
[1] f:80 typ:165 s(CHS):1023/254/63 e(CHS):1023/254/63 s:16771860 l:16771860
[2] f:00 typ:131 s(CHS):1023/254/63 e(CHS):1023/254/63 s:33543720 l:6120765
[3] f:00 typ:130 s(CHS):1023/254/63 e(CHS):1023/254/63 s:39664485 l:514080
GEOM: Configure ad0s1, start 32256 length 8587160064 end 8587192319
GEOM: Configure ad0s2, start 8587192320 length 8587192320 end 17174384639
GEOM: Configure ad0s3, start 17174384640 length 3133831680 end 20308216319
GEOM: Configure ad0s4, start 20308216320 length 263208960 end 20571425279
ad1: WARNING - SETFEATURES recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad1: WARNING - SETFEATURES recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad1: WARNING - SET_MULTI recovered from missing interrupt
GEOM: create disk ad1 dp=0xc2a9ab60
ad1: <Maxtor 5T040H4/TAH71DP0> ATA-6 disk at ata2-slave
ad1: 39083MB (80043264 sectors), 79408 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, PIO4
ad0: WARNING - READ_MUL recovered from missing interrupt
GEOM: Configure ad0s2a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s2b, start 268435456 length 268435456 end 536870911
GEOM: Configure ad0s2c, start 0 length 8587192320 end 8587192319
GEOM: Configure ad0s2d, start 536870912 length 268435456 end 805306367
GEOM: Configure ad0s2e, start 805306368 length 268435456 end 1073741823
GEOM: Configure ad0s2f, start 1073741824 length 7513450496 end 8587192319
GEOM: new disk ad1
ar: FreeBSD read conf failed
ad1: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad1: WARNING - READ_MUL recovered from missing interrupt
[0] f:00 typ:1 s(CHS):2/0/1 e(CHS):3/254/63 s:32130 l:32130
[1] f:00 typ:7 s(CHS):4/0/1 e(CHS):1023/254/63 s:64260 l:29639925
[2] f:80 typ:165 s(CHS):1023/254/63 e(CHS):1023/254/63 s:29704185 l:50331645
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad1s1, start 16450560 length 16450560 end 32901119
GEOM: Configure ad1s2, start 32901120 length 15175641600 end 15208542719
GEOM: Configure ad1s3, start 15208542720 length 25769802240 end 40978344959
ad1: WARNING - READ_MUL recovered from missing interrupt
ad1: WARNING - READ_MUL recovered from missing interrupt
ad1: WARNING - READ_MUL recovered from missing interrupt
GEOM: Configure ad1s3c, start 0 length 25769802240 end 25769802239
ad1: WARNING - READ_MUL recovered from missing interrupt
Mounting root from ufs:/dev/ad0s2a
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: WARNING - READ_MUL recovered from missing interrupt
ad0: TIMEOUT - READ_MUL retrying (2 retries left)
ata2: resetting devices ..
ata2: reset tp1 mask=03 ostat0=58 ostat1=50
ad0: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ad1: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
More information about the freebsd-current
mailing list