New interrupt code slows hyperthreading down
Jens Rehsack
rehsack at liwing.de
Fri Nov 7 12:17:02 PST 2003
John Baldwin wrote:
> On 07-Nov-2003 Jens Rehsack wrote:
>
>>Hi,
>>
>>I recompiled my system today and when it came up again,
>>it was terrible slow. Using top I've seen, that there're
>>around 25% cpu-time is used to handle interrupts.
>>The kernel was configured using SMP ('cause it's a HTT
>>enabled CPU) and APIC. Setting machdep.hlt_logical_cpus
>>to 1 didn't change anything. Simply getting a few mails
>>(around 30) takes about 20 minutes. Most of time while
>>getting the mails my mozilla was in "*Giant" state,
>>what shouldn't be good, should it?
>>
>>I've recompiled the kernel without SMP and APIC and
>>now the system's behaviour is more "normal". Is the
>>behaviour of the new interrupt code better on real
>>multiprocessor systems?
>
> Can you do a 'vmstat -i' under your SMP kernel to see where
> all the interrupts are coming from? It sounds like a device
> is interrupt storming. There has been report of this so far
> with fwohci(4).
It's attached as well as the dmesg output booting with -v.
Jens
-------------- next part --------------
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #0: Fri Nov 7 10:12:42 GMT 2003
root at statler:/usr/obj/usr/src/sys/STATLER
Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc087f000.
Calibrating clock(s) ... i8254 clock: 1193211 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2398854804 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2398.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1072889856 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x000000003ed0afff, 1041113088 bytes (254178 pages)
avail memory = 1032667136 (984 MB)
ACPI APIC Table: <A M I OEMAPIC >
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x31
pnpbios: Found PnP BIOS data at 0xc00f5580
pnpbios: Entry = f0000:616a Rev = 1.0
Other BIOS signatures found:
MADT: Found IO APIC ID 2, Vector 0 at 0xfec00000
ioapic0: intpin 0 -> ExtINT
ioapic0: intpin 1 -> irq 1
ioapic0: intpin 2 -> irq 2
ioapic0: intpin 3 -> irq 3
ioapic0: intpin 4 -> irq 4
ioapic0: intpin 5 -> irq 5
ioapic0: intpin 6 -> irq 6
ioapic0: intpin 7 -> irq 7
ioapic0: intpin 8 -> irq 8
ioapic0: intpin 9 -> irq 9
ioapic0: intpin 10 -> irq 10
ioapic0: intpin 11 -> irq 11
ioapic0: intpin 12 -> irq 12
ioapic0: intpin 13 -> irq 13
ioapic0: intpin 14 -> irq 14
ioapic0: intpin 15 -> irq 15
ioapic0: intpin 16 -> irq 16
ioapic0: intpin 17 -> irq 17
ioapic0: intpin 18 -> irq 18
ioapic0: intpin 19 -> irq 19
ioapic0: intpin 20 -> irq 20
ioapic0: intpin 21 -> irq 21
ioapic0: intpin 22 -> irq 22
ioapic0: intpin 23 -> irq 23
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: active-hi
MADT: intr override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: active-hi
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
VESA: information block
56 45 53 41 00 03 43 57 00 c0 01 00 00 00 cd 52
00 c0 00 02 04 01 58 57 00 c0 5f 57 00 c0 6b 57
00 c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
VESA: 23 mode(s) found
VESA: v3.0, 32768k memory, flags:0x1, mode table:0xc00c52cd (c00052cd)
VESA: Matrox Graphics Inc.
VESA: Matrox Matrox G550 00
null: <null device, zero device>
acpi0: <A M I OEMXSDT > on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25708086)
pcibios: BIOS version 2.10
Using $PIR table, 14 entries at 0xc00f5410
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 2 8 A 0x68 3 4 5 6 7 10 11 12 14 15
embedded 0 31 A 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 31 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 0 29 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 29 B 0x63 3 4 5 6 7 10 11 12 14 15
embedded 0 29 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 29 D 0x6b 3 4 5 6 7 10 11 12 14 15
embedded 0 1 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 1 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 0 3 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 3 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 0 3 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 3 D 0x63 3 4 5 6 7 10 11 12 14 15
slot 1 2 9 A 0x69 3 4 5 6 7 10 11 12 14 15
slot 1 2 9 B 0x6a 3 4 5 6 7 10 11 12 14 15
slot 1 2 9 C 0x6b 3 4 5 6 7 10 11 12 14 15
slot 1 2 9 D 0x68 3 4 5 6 7 10 11 12 14 15
slot 2 2 10 A 0x6a 3 4 5 6 7 10 11 12 14 15
slot 2 2 10 B 0x6b 3 4 5 6 7 10 11 12 14 15
slot 2 2 10 C 0x68 3 4 5 6 7 10 11 12 14 15
slot 2 2 10 D 0x69 3 4 5 6 7 10 11 12 14 15
slot 3 2 11 A 0x6b 3 4 5 6 7 10 11 12 14 15
slot 3 2 11 B 0x68 3 4 5 6 7 10 11 12 14 15
slot 3 2 11 C 0x69 3 4 5 6 7 10 11 12 14 15
slot 3 2 11 D 0x6a 3 4 5 6 7 10 11 12 14 15
embedded 0 1 A 0x62 3 4 5 6 7 10 11 12 14 15
slot 4 2 12 A 0x68 3 4 5 6 7 10 11 12 14 15
slot 4 2 12 B 0x69 3 4 5 6 7 10 11 12 14 15
slot 4 2 12 C 0x6a 3 4 5 6 7 10 11 12 14 15
slot 4 2 12 D 0x6b 3 4 5 6 7 10 11 12 14 15
slot 5 2 13 A 0x69 3 4 5 6 7 10 11 12 14 15
slot 5 2 13 B 0x6a 3 4 5 6 7 10 11 12 14 15
slot 5 2 13 C 0x6b 3 4 5 6 7 10 11 12 14 15
slot 5 2 13 D 0x68 3 4 5 6 7 10 11 12 14 15
embedded 2 3 A 0x68 3 4 5 6 7 10 11 12 14 15
embedded 2 4 A 0x6b 3 4 5 6 7 10 11 12 14 15
embedded 2 5 A 0x6a 3 4 5 6 7 10 11 12 14 15
AcpiOsDerivePciId: bus 0 dev 31 func 1
AcpiOsDerivePciId: bus 0 dev 31 func 2
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu1: <CPU> port 0x530-0x537 on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f8000000, size 26, enabled
found-> vendor=0x8086, dev=0x2570, revid=0x02
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2571, revid=0x02
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000ef00, size 5, enabled
pcib0: matched entry for 0.29.INTA (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24d2, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=16
map[20]: type 4, range 32, base 0000ef20, size 5, enabled
pcib0: matched entry for 0.29.INTB (source )
pcib0: device is hardwired to IRQ 19
found-> vendor=0x8086, dev=0x24d4, revid=0x02
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=19
map[20]: type 4, range 32, base 0000ef40, size 5, enabled
pcib0: matched entry for 0.29.INTC (source )
pcib0: device is hardwired to IRQ 18
found-> vendor=0x8086, dev=0x24d7, revid=0x02
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=18
map[20]: type 4, range 32, base 0000ef80, size 5, enabled
pcib0: matched entry for 0.29.INTA (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24de, revid=0x02
bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=16
map[10]: type 1, range 32, base febfbc00, size 10, enabled
pcib0: matched entry for 0.29.INTD (source )
pcib0: device is hardwired to IRQ 23
found-> vendor=0x8086, dev=0x24dd, revid=0x02
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=23
powerspec 2 supports D0 D3 current D0
found-> vendor=0x8086, dev=0x244e, revid=0xc2
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x24d0, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 00000000, size 3, enabled
map[14]: type 4, range 32, base 00000000, size 2, enabled
map[18]: type 4, range 32, base 00000000, size 3, enabled
map[1c]: type 4, range 32, base 00000000, size 2, enabled
map[20]: type 4, range 32, base 0000fc00, size 4, enabled
found-> vendor=0x8086, dev=0x24db, revid=0x02
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[20]: type 4, range 32, base 00000400, size 5, enabled
pcib0: matched entry for 0.31.INTB (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x24d3, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=17
agp0: <Intel 82865 host to AGP bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 64M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xfd900000-0xfe9fffff
pcib1: prefetched decode 0xf3f00000-0xf7efffff
pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P1 - AE_NOT_FOUND
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 3, range 32, base f4000000, size 25, enabled
map[14]: type 1, range 32, base fe9fc000, size 14, enabled
map[18]: type 1, range 32, base fe000000, size 23, enabled
found-> vendor=0x102b, dev=0x2527, revid=0x01
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=4 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x10 (4000 ns), maxlat=0x20 (8000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
drm0: <Matrox G550 (AGP)> mem 0xfe000000-0xfe7fffff,0xfe9fc000-0xfe9fffff,0xf4000000-0xf5ffffff irq 11 at device 0.0 on pci1
info: [drm] AGP at 0xf8000000 64MB
info: [drm] Initialized mga 3.1.0 20021029 on minor 0
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xef00-0xef1f irq 16 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xef20-0xef3f irq 19 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/11.10, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xef40-0xef5f irq 18 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xef80-0xef9f irq 16 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebfbc00-0xfebfbfff irq 23 at device 29.7 on pci0
ehci0: (New EHCI DeviceId=0x24dd8086)
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
ehci_pci_attach: companion usb3
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xd000-0xdfff
pcib2: memory decode 0xfea00000-0xfeafffff
pcib2: prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
map[10]: type 1, range 32, base feaff800, size 11, enabled
map[14]: type 4, range 32, base 0000dc00, size 7, enabled
pcib2: matched entry for 2.3.INTA (source )
pcib2: device is hardwired to IRQ 20
found-> vendor=0x1106, dev=0x3044, revid=0x80
bus=2, slot=3, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0210, cachelnsz=4 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x20 (8000 ns)
intpin=a, irq=20
powerspec 2 supports D0 D2 D3 current D0
map[10]: type 1, range 32, base feaf8000, size 14, enabled
map[14]: type 4, range 32, base 0000d800, size 8, enabled
pcib2: matched entry for 2.5.INTA (source )
pcib2: device is hardwired to IRQ 22
found-> vendor=0x10b7, dev=0x1700, revid=0x12
bus=2, slot=5, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x02b0, cachelnsz=4 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
intpin=a, irq=22
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000d480, size 7, enabled
map[14]: type 1, range 32, base feaff400, size 7, enabled
pcib2: matched entry for 2.10.INTA (source )
pcib2: device is hardwired to IRQ 22
found-> vendor=0x10b7, dev=0x9200, revid=0x74
bus=2, slot=10, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0210, cachelnsz=4 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
intpin=a, irq=22
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000df40, size 5, enabled
pcib2: matched entry for 2.12.INTA (source )
pcib2: device is hardwired to IRQ 20
found-> vendor=0x1102, dev=0x0002, revid=0x08
bus=2, slot=12, func=0
class=04-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0105, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=20
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000dfe0, size 3, enabled
found-> vendor=0x1102, dev=0x7002, revid=0x08
bus=2, slot=12, func=1
class=09-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0105, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D1 D2 D3 current D0
fwohci0: <VIA VT6306> port 0xdc00-0xdc7f mem 0xfeaff800-0xfeafffff irq 20 at device 3.0 on pci2
fwohci0: latency timer 64 -> 64.
fwohci0: cache size 4 -> 8.
pcib2: device fwohci0 requested decoded memory range 0xfeaff800-0xfeafffff
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:e0:18:00:00:20:ae:b5
fwohci0: resetting OHCI...done (loop=0)
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x3 loop=1, retry=0
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xf800a202 -> 0xf800a202
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
skc0: <3Com 3C940 Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfeaf8000-0xfeafbfff irq 22 at device 5.0 on pci2
pcib2: device skc0 requested decoded memory range 0xfeaf8000-0xfeafbfff
skc0: 3Com Gigabit LOM (3C940)
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: Ethernet address: 00:0c:6e:52:46:80
sk0: bpf attached
miibus0: <MII bus> on sk0
e1000phy0: <Marvell 88E1000 Gigabit PHY> on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xd480-0xd4ff mem 0xfeaff400-0xfeaff47f irq 22 at device 10.0 on pci2
pcib2: device xl0 requested decoded memory range 0xfeaff400-0xfeaff47f
xl0: using memory mapped I/O
xl0: Ethernet address: 00:01:02:9b:c3:c3
xl0: media options word: a
xl0: found MII/AUTO
miibus1: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus1
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
pcm0: <Creative EMU10K1> port 0xdf40-0xdf5f irq 20 at device 12.0 on pci2
pcib2: device pcm0 requested decoded I/O range 0xdf40-0xdf5f
emu: setmap (3bf000, 800), nseg=1, error=0
emu: setmap (39e000, 1000), nseg=1, error=0
pcm0: <SigmaTel STAC9721/23 AC97 Codec (id = 0x83847609)>
pcm0: Codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features AMAP
emu: setmap (35c000, 1000), nseg=1, error=0
emu: setmap (37a000, 1000), nseg=1, error=0
emu: setmap (338000, 1000), nseg=1, error=0
emu: setmap (376000, 1000), nseg=1, error=0
pcm0: sndbuf_setmap 3e1d4000, 1000; 0xc69e0000 -> 3e1d4000
pcm0: sndbuf_setmap 39b000, 1000; 0xc6a07000 -> 39b000
pcm0: sndbuf_setmap 359000, 1000; 0xc6a05000 -> 359000
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata1-slave: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata1-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata1-slave: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata1-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata1-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 mask=03 stat0=50 stat1=00 devices=0x9<ATAPI_SLAVE,ATA_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
ichsmb0: <Intel 82801EB (ICH5) SMBus controller> port 0x400-0x41f irq 17 at device 31.3 on pci0
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus generic I/O> on smbus0
acpi_button0: <Power Button> on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
unknown: not probed (disabled)
speaker0 port 0x61 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 on acpi0
uart0: fast interrupt
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc9000-0xc97ff,0xc0000-0xc8fff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0 failed to probe at port 0x3f8 irq 4 flags 0x10 on isa0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x700ff
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 2398854804 Hz quality -100
Timecounters tick every 10.000 msec
IP Filter: v3.4.31 initialized. Default = block all, Logging = enabled
lo0: bpf attached
Current DB 0
ch = 0
Current OP KEY INT BR len Addr Depend Stat: Cnt
3e192000 OUTL ST2 ALL ALL 12 00000000 3e192080 8411:0008 RUN,ACTIVE, ack complete(11)
0x000000e0 0x00450000 0xffbaffff 0x00000000
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ata0-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad0: setting UDMA100 on Intel ICH5 chip
GEOM: create disk ad0 dp=0xc6bc9870
ad0: <IC35L090AVV207-0/V23OA66A> ATA-6 disk at ata0-master
ad0: 78533MB (160836480 sectors), 159560 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:160826652
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 82343245824 end 82343278079
ad1: setting UDMA100 on Intel ICH5 chip
GEOM: create disk ad1 dp=0xc6bc9670
ad1: <IBM-DTLA-307060/TX8OA50C> ATA-5 disk at ata0-slave
ad1: 58644MB (120103200 sectors), 119150 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, UDMA100
ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
GEOM: Configure ad0s1a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s1b, start 268435456 length 4294967296 end 4563402751
GEOM: Configure ad0s1c, start 0 length 82343245824 end 82343245823
GEOM: Configure ad0s1d, start 4563402752 length 4294967296 end 8858370047
GEOM: Configure ad0s1e, start 8858370048 length 32212254720 end 41070624767
GEOM: Configure ad0s1f, start 41070624768 length 10737418240 end 51808043007
GEOM: Configure ad0s1g, start 51808043008 length 30535202816 end 82343245823
GEOM: new disk ad1
ata1-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad2: setting UDMA100 on Intel ICH5 chip
GEOM: create disk ad2 dp=0xc6bc9070
ad2: <SAMSUNG SV1204H/RK100-15> ATA-6 disk at ata1-master
ad2: 114498MB (234493056 sectors), 232632 C, 16 H, 63 S, 512 B
ad2: 16 secs/int, 1 depth queue, UDMA100
acd0: setting PIO4 on Intel ICH5 chip
acd0: <_NEC DV-5800C/D9S2> DVDROM drive at ata1 as slave
acd0: read 8268KB/s (8268KB/s), 512KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/11/63 s:63 l:120101877
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad1s1, start 32256 length 61492161024 end 61492193279
GEOM: new disk ad2
GEOM: Configure ad1s1c, start 0 length 61492161024 end 61492161023
GEOM: Configure ad1s1d, start 0 length 61492161024 end 61492161023
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/11/63 s:63 l:234484677
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad2s1, start 32256 length 120056154624 end 120056186879
GEOM: Configure ad2s1c, start 0 length 120056154624 end 120056154623
GEOM: Configure ad2s1d, start 0 length 120056154624 end 120056154623
bus_explore done
ums0: at uhub1 port 1 (addr 2) disconnected
ums0: detached
ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/11.10, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
pass0 at ata1 bus 0 target 1 lun 0
pass0: <_NEC DV-5800C D9S2> Removable CD-ROM SCSI-0 device
pass0: 16.000MB/s transfers
GEOM: create disk cd0 dp=0xc6bdee00
GEOM: new disk cd0
(cd0:ata1:0:1:0): Retrying Command
(cd0:ata1:0:1:0): Recovered Sense
(cd0:ata1:0:1:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ata1:0:1:0): CAM Status: SCSI Status Error
(cd0:ata1:0:1:0): SCSI Status: Check Condition
(cd0:ata1:0:1:0): NOT READY asc:3a,0
(cd0:ata1:0:1:0): Medium not present
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
cd0 at ata1 bus 0 target 1 lun 0
cd0: <_NEC DV-5800C D9S2> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x02000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 13 (IRQ 13) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic0: routing intpin 16 (IRQ 16) to cluster 0
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
ioapic0: routing intpin 20 (IRQ 20) to cluster 0
ioapic0: routing intpin 22 (IRQ 22) to cluster 0
ioapic0: routing intpin 23 (IRQ 23) to cluster 0
(cd0:ata1:0:1:0): Retrying Command
(cd0:ata1:0:1:0): Recovered Sense
(cd0:ata1:0:1:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ata1:0:1:0): CAM Status: SCSI Status Error
(cd0:ata1:0:1:0): SCSI Status: Check Condition
(cd0:ata1:0:1:0): NOT READY asc:3a,0
(cd0:ata1:0:1:0): Medium not present
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
(cd0:ata1:0:1:0): Retrying Command
(cd0:ata1:0:1:0): Recovered Sense
(cd0:ata1:0:1:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ata1:0:1:0): CAM Status: SCSI Status Error
(cd0:ata1:0:1:0): SCSI Status: Check Condition
(cd0:ata1:0:1:0): NOT READY asc:3a,0
(cd0:ata1:0:1:0): Medium not present
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
agp0: Setting AGP v2 mode 4
ioapic0: routing intpin 11 (IRQ 11) to cluster 0
drm0: [MPSAFE]
-------------- next part --------------
interrupt total rate
irq1: atkbd0 512 2
irq8: rtc 23419 127
irq13: npx0 1 0
irq14: ata0 4422 24
irq15: ata1 82 0
irq16: uhci0 uhci3 5379815 29238
irq19: uhci1 21 0
irq20: fwohci0 pcm0 2 0
irq22: skc0 xl0 1268 6
irq23: ehci0 1 0
irq0: clk 18297 99
Total 5427840 29499
More information about the freebsd-current
mailing list