New interrupt stuff breaks ASUS 2 CPU system

Harti Brandt brandt at fokus.fraunhofer.de
Wed Nov 5 02:23:28 PST 2003


On Tue, 4 Nov 2003, John Baldwin wrote:

JB>
JB>On 04-Nov-2003 Harti Brandt wrote:
JB>> On Tue, 4 Nov 2003, Harti Brandt wrote:
JB>>
JB>> HB>On Tue, 4 Nov 2003, John Baldwin wrote:
JB>> HB>
JB>> HB>JB>
JB>> HB>JB>On 04-Nov-2003 Harti Brandt wrote:
JB>> HB>JB>>
JB>> HB>JB>> Hi,
JB>> HB>JB>>
JB>> HB>JB>> I have an ASUS system with 2 CPUs that I need to run at HZ=10000. This
JB>> HB>JB>> worked until yesterday, but with the new interrupt code it doesn't boot
JB>> HB>JB>> anymore. It works for the standard HZ, but if I set HZ=1000 I get a double
JB>> HB>JB>> fault. I suspect a race condition in the interrupt handling. My config
JB>> HB>JB>> file has
JB>> HB>JB>>
JB>> HB>JB>> options SMP
JB>> HB>JB>> device apic
JB>> HB>JB>> options HZ=1000
JB>> HB>JB>
JB>> HB>JB>Ok, I can try to reproduce.
JB>> HB>JB>
JB>> HB>JB>> Device configuration finished.
JB>> HB>JB>> Timecounter "TSC" frequency 1380009492 Hz quality -100
JB>> HB>JB>> Timecounters cpuid = 0; apic id = 00
JB>> HB>JB>> instruction pointer   = 0x8:0xc048995d
JB>> HB>JB>> stack pointer         = 0x10:0xc0821bf4
JB>> HB>JB>> frame pointer        cpuid = 0; apic id = 00
JB>> HB>JB>>
JB>> HB>JB>> 0xc048995d is in critical_exit. It is the jmp after the popf from
JB>> HB>JB>> cpu_critical_exit.
JB>> HB>JB>
JB>> HB>JB>This is where interrupts are re-enabled, so you are getting an interrupt.
JB>> HB>JB>It might be helpful to figure what type of fault you are actually getting.
JB>> HB>
JB>> HB>tf_err is 0, tf_trapno is 30 (decimal).
JB>>
JB>> More information:
JB>>
JB>> I have replaced all the reserved vectors with individual ones, that set
JB>> tf_err to the index (vector number). It appears the the vector number is
JB>> 39 decimal. What does that mean?
JB>
JB>IRQ 7.
JB>Can you post a verbose dmesg?  Also, can you try both with and without
JB>ACPI?

Attached are both dmesgs.

More datapoints:

I had the parallel port (irq7) and the second sio disabled in the BIOS.
After enabling both I now get a panic in lapic_handle_intr: Couldn't get
vector from ISR! After fetching the relevant docs from intel I checked the
registers of the apic pointed to by lapic. The interrupt taken is
Xapic_irq1. isr1 is zero, but irr1 is 0x100 (that was without ACPI). How
may that happen? As I understand ISR are the interrupts that have been
delivered to the CPU so if it is interrupted a bit should be set, correct?

I then have replaced the panic by a printf() followed by a return. Now the
system comes to live, but I get a couple of these warnings. When the
system is idle everyting seems fine, but when I start my simulation
application (which normally generates between 20k and 250k interrupts/sec
depending on the MPSAFE setting of the ATM drivers) I get approx 1-2 of
these messages per second (this is with HZ=1000).

A question while reading the code: what does the global lapic variable
refer to? As I understand every CPU has its local APIC. Does it point to
one of those two? To which?

Regards,
harti
-- 
harti brandt,
http://www.fokus.fraunhofer.de/research/cc/cats/employees/hartmut.brandt/private
brandt at fokus.fraunhofer.de, harti at freebsd.org
-------------- next part --------------
 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x378-0x37f on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
psmcpnp0: <PS/2 mouse port> at irq 12 on isa0
psm0: current command byte:0065
psm0: failed to reset the aux device.
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
speaker0: <PC speaker> at port 0x61 on isa0
Device configuration finished.
Timecounter "TSC" frequency 1380008649 Hz quality -100
Timecounters tick every 1.000Couldn't get vector from ISR! msec
lo0: bpf attached
ata0-master: pio=0Couldn't get vector from ISR!x0c wdma=0x22 uCouldn't get vector from ISR!dma=0x45 caCouldn't get vector from ISR!ble=80pin
ad0: setting UDMA100 on AMD 768 chip
GEOM: creatCouldn't get vector from ISR!e disk ad0 dp=0Couldn't get vector from ISR!xc629e970
ad0:Couldn't get vector from ISR! <ST340810A/3.3Couldn't get vector from ISR!9> ATA-6 disk aCouldn't get vector from ISR!t ata0-master
Couldn't get vector from ISR!ad0: 38166MB (7Couldn't get vector from ISR!8165360 sectorsCouldn't get vector from ISR!), 77545 C,Couldn't get vector from ISR! 16 H, 63 S, 512 BCouldn't get vector from ISR!
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
Couldn't get vector from ISR!ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
acd0: setting PICouldn't get vector from ISR!O4 on AMD 768 cCouldn't get vector from ISR!hip
acd0: <TOSCouldn't get vector from ISR!HIBA CD-ROMCouldn't get vector from ISR! XM-6702B/1005> CDRCouldn't get vector from ISR!OM drive at ataCouldn't get vector from ISR!1 as masterCouldn't get vector from ISR!
acd0: read 82Couldn't get vector from ISR!68KB/s (8268KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream
acd0: Writes:
acd0: Audio: play, 16 volume levels
acd0: MechanCouldn't get vector from ISR!ism: ejectable Couldn't get vector from ISR!tray, unlockedCouldn't get vector from ISR!
acd0: MediCouldn't get vector from ISR!um: no/blank disc
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
i[o0a]p ifc:08:0  rtoyupt:i1n6g5  isn(tCpHiSn) :10 /(1I/R1Q  e1(CCHoSu)l:d1n0'2t3 /g2e5t4 /v6e3c tso:r6 3f rlo:m7 8I1S5R6!)1 6t2o 
c[l1u]s tfe:r0 00 t
yipo:a0p si(cCHCSo)u:l0d/n0'/t0  gee(tC HvSe)c:t0o/r0 /f0r osm: 0I SlR:!00: 
r[o2u]t ifn:g0 0i nttyppi:n0  3s ((CIHRSQ) :03/)0 /t0o  ec(lCuHsSt)e:r0 /00/
0i osa:p0i cl0::0 r
o[u3t]i nfg: 0i0n ttpyipn: 04  s((ICRHQS) :40)/ 0t/o0  cel(uCsHtSe)r: 00/0/
0i osa:p0 ilc:00:
 routGiEnOgM :i nCtopnifni g6u r(eI RaQd 06s)1 ,t os tcalruts t3e2r2 506 
lieonagptihc 04:0 0r1o5u9t5i4n9g4 4i netnpdi n4 070 1(5I9R8Q7 179)9 t
o cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 13Couldn't get vector from ISR! (IRQ 13) to clCouldn't get vector from ISR!uster 0
ioapicCouldn't get vector from ISR!0: routing intpCouldn't get vector from ISR!in 14 (IRQ Couldn't get vector from ISR!14) to cluster Couldn't get vector from ISR!0
ioapic0: rouCouldn't get vector from ISR!ting intpin 15 (IRQ 15) to cluster 0
GEOM: Configure ad0s1a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s1b, start 268435456 length 1052180480 end 1320615935
GEOM: Configure ad0s1c, start 0 length 40015954944 end 40015954943
GEOM: Configure ad0s1d, start 1320615936 length 268435456 end 1589051391
GEOM: Configure ad0s1e, start 1589051392 length 268435456 end 1857486847
GEOM: Configure ad0s1f, start 1857486848 length 38158468096 end 40015954943
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xc400-0xc47f mem 0xf7000000-0xf700007f irq 18 at device 5.0 on pci2
pcib2: device xl0 requested decoded memory range 0xf7000000-0xf700007f
xl0: using memory mapped I/O
xl0: Ethernet address: 00:01:02:df:1c:b9
xl0: media options word: a
xl0: found MII/AUTO
xl0: bpf attached
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hatm0: <FORE HE> mem 0xf8000000-0xf80fffff irq 16 at device 8.0 on pci0
hatm0: carrier detected
hatm0: bpf attached
ioapic0: routing inCouldn't get vector from ISR!tpin 16 (IRQ 16) to cluster 0
hatm1: <FORE HE> mem 0xf6800000-0xf68fffff irq 17 at device 6.0 on pci2
pcib2: device hatm1 requested decoded memory range 0xf6800000-0xf68fffff
hatm1: hw.hatm1.rbps1_size=4096
hatm1: hw.hatm1.rbps1_thresh=2048
hatm1: hw.hatm1.tpdrq_size=4096
hatm1: hw.hatm1.tpdmax=0
hatm1: hw.hatm1.max_mbuf_pages=2048
hatm1: hw.hatm1.mpsafe=1
hatm1: carrier detCouldn't get vector from ISR!ected
hatm1: bpf attached
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
hatm2: <FORE HE> mem 0xf6000000-0xf60fffff irq 19 at device 8.0 on pci2
pcib2: device hatm2 requested decodCouldn't get vector from ISR!ed memory range 0xf6000000-0xf60fffff
hatm2: hw.hatm2.rbps1_size=4096
hatm2: hw.hatm2.rbps1_thresh=2048
hatm2: hw.hatm2.tbrq0_size=8192
hatm2: hw.hatm2.tbrq0_thresh=6400
hatm2: hw.hatm2.tpdrq_sizeC=o4u0l9d6n
'hta tgme2t:  vhewc.thoart mf2r.otmp dImSaRx!=0
hatm2: hw.hatm2.mpsafe=1
hatm2: carrier detected
hatm2: bpf attached
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
hatm0: ForeRunnerHE 622, Rev. D, S/N 2949834, MAC=00:20:48:2d:02:ca (64bit PCI)
hatm1: ForeRunnerHE 155, Rev. B, S/N 3026384, MAC=00:20:48:2e:2d:d0 (32bit PCI)
hatm2: ForeRunnerHE 155, Rev. B, S/N 3027669, MAC=00:20:48:2e:32:d5 (32bit PCI)
hatm0: txmbuf leaves 0
boot() called on cpu#1
Waiting (max 60 seconds) for system process `vnlru' to stop...stopped
Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped
Waiting (max 60 seconds) for system process `syncer' to stop...stopped

syncing disks, buffers remaining... 1 
done
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #33: Wed Nov  5 10:55:08 CET 2003
    hbb at beagle.fokus.fraunhofer.de:/opt/obj/usr/src/sys/MARIPOSA
Preloaded elf kernel "/boot/kernel/kernel" at 0xc06ea000.
Preloaded elf module "/boot/kernel/random.ko" at 0xc06ea278.
Calibrating clock(s) ... i8254 clock: 1193137 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1380011703 Hz
CPU: AMD Athlon(TM) MP 1800+ (1380.01-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x662  Stepping = 2
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0480000<MP,AMIE,DSP,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory  = 536788992 (511 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000829000 - 0x000000001f6c5fff, 518639616 bytes (126621 pages)
avail memory = 516001792 (492 MB)
ACPI APIC Table: <ASUS   A7M266-D>
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
bios32: Found BIOS32 Service Directory header at 0xc00f2560
bios32: Entry = 0xf1d20 (c00f1d20)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x1f20
pnpbios: Found PnP BIOS data at 0xc00fc5e0
pnpbios: Entry = f0000:c610  Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
MADT: Found IO APIC ID 2, Vector 0 at 0xfec00000
ioapic0: intpin 0 -> ExtINT
ioapic0: intpin 1 -> irq 1
ioapic0: intpin 2 -> irq 2
ioapic0: intpin 3 -> irq 3
ioapic0: intpin 4 -> irq 4
ioapic0: intpin 5 -> irq 5
ioapic0: intpin 6 -> irq 6
ioapic0: intpin 7 -> irq 7
ioapic0: intpin 8 -> irq 8
ioapic0: intpin 9 -> irq 9
ioapic0: intpin 10 -> irq 10
ioapic0: intpin 11 -> irq 11
ioapic0: intpin 12 -> irq 12
ioapic0: intpin 13 -> irq 13
ioapic0: intpin 14 -> irq 14
ioapic0: intpin 15 -> irq 15
ioapic0: intpin 16 -> irq 16
ioapic0: intpin 17 -> irq 17
ioapic0: intpin 18 -> irq 18
ioapic0: intpin 19 -> irq 19
ioapic0: intpin 20 -> irq 20
ioapic0: intpin 21 -> irq 21
ioapic0: intpin 22 -> irq 22
ioapic0: intpin 23 -> irq 23
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: active-hi
MADT: intr override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: active-lo
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: active-hi
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: active-hi
ioapic0 <Version 17> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
null: <null device, zero device>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
random: <entropy source>
acpi0: <ASUS   A7M266-D> on motherboard
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80012848
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=700c1022)
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00f24a0
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    7    B   0x01  3 4 5 7 9 10 11 12
embedded    0    7    C   0x02  3 4 5 7 9 10 11 12
embedded    0    7    D   0x03  3 4 5 7 9 10 11 12
slot 1      0    8    B   0x01  3 4 5 7 9 10 11 12
slot 1      0    8    C   0x02  3 4 5 7 9 10 11 12
slot 1      0    8    D   0x03  3 4 5 7 9 10 11 12
slot 2      0    9    A   0x01  3 4 5 7 9 10 11 12
slot 2      0    9    B   0x02  3 4 5 7 9 10 11 12
slot 2      0    9    C   0x03  3 4 5 7 9 10 11 12
slot 3      2    6    A   0x01  3 4 5 7 9 10 11 12
slot 3      2    6    B   0x02  3 4 5 7 9 10 11 12
slot 3      2    6    C   0x03  3 4 5 7 9 10 11 12
slot 4      2    5    A   0x02  3 4 5 7 9 10 11 12
slot 4      2    5    B   0x03  3 4 5 7 9 10 11 12
slot 4      2    5    D   0x01  3 4 5 7 9 10 11 12
slot 5      2    8    A   0x03  3 4 5 7 9 10 11 12
slot 5      2    8    C   0x01  3 4 5 7 9 10 11 12
slot 5      2    8    D   0x02  3 4 5 7 9 10 11 12
embedded    1    5    B   0x01  3 4 5 7 9 10 11 12
embedded    1    5    C   0x02  3 4 5 7 9 10 11 12
embedded    1    5    D   0x03  3 4 5 7 9 10 11 12
embedded    2    4    A   0x01  3 4 5 7 9 10 11 12
embedded    2    4    B   0x02  3 4 5 7 9 10 11 12
embedded    2    4    C   0x03  3 4 5 7 9 10 11 12
embedded    2    0    B   0x01  3 4 5 7 9 10 11 12
embedded    2    0    C   0x02  3 4 5 7 9 10 11 12
embedded    2    0    D   0x03  3 4 5 7 9 10 11 12
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 3
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
	map[10]: type 3, range 32, base fc000000, size 25, enabled
	map[14]: type 3, range 32, base fb800000, size 12, enabled
	map[18]: type 4, range 32, base 0000e800, size  2, port disabled
found->	vendor=0x1022, dev=0x700c, revid=0x11
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x700d, revid=0x00
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7440, revid=0x04
	bus=0, slot=7, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000d800, size  4, enabled
found->	vendor=0x1022, dev=0x7441, revid=0x04
	bus=0, slot=7, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7443, revid=0x03
	bus=0, slot=7, func=3
	class=06-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 1, range 32, base f8000000, size 20, enabled
pcib0: matched entry for 0.8.INTA (source )
pcib0: device is hardwired to IRQ 20
found->	vendor=0x1127, dev=0x0400, revid=0x00
	bus=0, slot=8, func=0
	class=02-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0016, statreg=0x0220, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x01 (250 ns)
	intpin=a, irq=20
found->	vendor=0x1022, dev=0x7448, revid=0x04
	bus=0, slot=16, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0017, statreg=0x2220, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xe000-0xdfff
pcib1:   memory decode     0xf8800000-0xf9bfffff
pcib1:   prefetched decode 0xf9f00000-0xfb7fffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
	map[10]: type 3, range 32, base fa000000, size 24, enabled
	map[14]: type 1, range 32, base f9000000, size 14, enabled
	map[18]: type 1, range 32, base f8800000, size 23, enabled
pcib1: matched entry for 1.5.INTA (source )
pcib1: device is hardwired to IRQ 16
found->	vendor=0x102b, dev=0x0521, revid=0x01
	bus=1, slot=5, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x10 (4000 ns), maxlat=0x20 (8000 ns)
	intpin=a, irq=16
	powerspec 1  supports D0 D3  current D0
pci1: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 768 UDMA100 controller> port 0xd800-0xd80f at device 7.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave:  stat=0x00 err=0x04 lsb=0x7f msb=0x7f
ata1: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pci0: <network, ATM> at device 8.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xc000-0xcfff
pcib2:   memory decode     0xf6000000-0xf7ffffff
pcib2:   prefetched decode 0xf9c00000-0xf9dfffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
	map[10]: type 4, range 32, base 0000c800, size  8, enabled
pcib2: matched entry for 2.4.INTA (source )
pcib2: device is hardwired to IRQ 17
found->	vendor=0x13f6, dev=0x0111, revid=0x10
	bus=2, slot=4, func=0
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0085, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 0000c400, size  7, enabled
	map[14]: type 1, range 32, base f7000000, size  7, enabled
pcib2: matched entry for 2.5.INTA (source )
pcib2: device is hardwired to IRQ 18
found->	vendor=0x10b7, dev=0x9200, revid=0x74
	bus=2, slot=5, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base f6800000, size 20, enabled
pcib2: matched entry for 2.6.INTA (source )
pcib2: device is hardwired to IRQ 17
found->	vendor=0x1127, dev=0x0400, revid=0x01
	bus=2, slot=6, func=0
	class=02-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0016, statreg=0x0220, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x01 (250 ns)
	intpin=a, irq=17
	map[10]: type 1, range 32, base f6000000, size 20, enabled
pcib2: matched entry for 2.8.INTA (source )
pcib2: device is hardwired to IRQ 19
found->	vendor=0x1127, dev=0x0400, revid=0x01
	bus=2, slot=8, func=0
	class=02-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0016, statreg=0x0220, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x01 (250 ns)
	intpin=a, irq=19
pci2: <multimedia, audio> at device 4.0 (no driver attached)
pci2: <network, ethernet> at device 5.0 (no driver attached)
pci2: <network, ATM> at device 6.0 (no driver attached)
pci2: <network, ATM> at device 8.0 (no driver attached)
unknown: not probed (disabled)
speaker0 port 0x61 on acpi0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sio0: irq maps: 0xc0c1 0xc0d1 0xc0c1 0xc0c1
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
sio1: irq maps: 0xc0c1 0xc0c9 0xc0c1 0xc0c1
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: unable to allocate IRQ
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc8000-0xc87ff,0xc0000-0xc7fff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 50 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounter "TSC" frequency 1380011703 Hz qualitCouldn't get vector from ISR!y -100
Timecounters tick every 1.000 Couldn't get vector from ISR!msec
lo0: bpf attached
acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0%
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad0: setting UDMA100 on AMD 768 chip
GEOM: create disk ad0 dp=0xc63bbd70
ad0: <ST340810A/3.39> ATA-6 disk at ata0Couldn't get vector from ISR!-master
ad0: 38166MB (78165360 sectors), 77545 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
ata1-master: pioCouldn't get vector from ISR!=0x0c wdma=0x22 udma=0x42 cable=40pin
[0] f:80 typ:165 s(CHS):0/1/1 e(CCouldn't get vector from ISR!HS):1023/Couldn't get vector from ISR!254/63 s:63 l:78156162
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:Couldn't get vector from ISR!0 l:0
GEOM: ConCouldn't get vector from ISR!figure ad0s1, stCouldn't get vector from ISR!art 32256 length 4001595494Couldn't get vector from ISR!4 end 40015987199
acd0: setting PIO4 on AMD 768 chip
acd0: <TOSHIBA CD-ROM XM-6702B/1005> CDROM drive at ata1 as master
acdCouldn't get vector from ISR!0: read 8268KB/s (8268KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream
acd0: Writes:
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapiGcE0O:M :r oCuotnifnigg uirnet paidn0 s11 a(,I RstQa r1t)  0t ol ecnlgutsht e2r6 8043
5i4o5a6p iecn0d:  2r6o8u4t3i5n4g5 5in
tGpEiOnM :3  C(oInRfQi g3u)r et oa d0csl1ub,s tsetra r0t 
2i6o8a4p3i5c405:6  rloeuntgitnhg  1i0n5t2p1i8n0 448 0( IeRnQd  41)3 2t0o6 1c5l9u3s5te
rG E0OM
:i oCaopnifci0g:u rreo uatdi0nsg1 ci,n tsptianr t6  0( IlReQn g6t)h  4t0o0 1c5l9u5s4t9e4r4  0en
di o4a0p0i1c509:5 4r9o4u3ti
nGgE OiMn:t pCionn f7ig u(rIeR Qa d70)s 1tdo,  csltuasrtte r1 3020
6i1o5a9p3i6c 0l:e nrgotuht i2n6g84 3i5n4t5p6i ne n8d  (1I5R8Q9 085)1 3t9o1 c
lGuEsOtMe:r  C0on
fiiogaupriec 0a:d 0rso1uet,i nsgt airtn t1p5i8n9 095 1(3I9R2Q  l9e)n gttoh  c2l6u8s4t3e5r4 506 
einoda p1i8c507:4 8r6o8u4t7in
gG EiOnMt:p iCno n1f3i g(uIrReQ  a1d30)s 1tfo,  csltuasrtte r1 8057
4i8o6a8p4i8c 0l:e nrgotuht i3n8g1 5i8n4t6p8i0n9 61 4e n(dI R4Q0 01145)9 5t4o9 4c3lu
ster 0
ioapic0: routCouldn't get vector from ISR!ing intpin 15 (IRQ Couldn't get vector from ISR!15) to cluster Couldn't get vector from ISR!0
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xc400-0xc47f mem 0xf7000000-0xf700007f irq 18 at device 5.0 on pci2
pcib2: device xl0 requested decoded memory range 0xf7000000-0xf700007f
xl0: using memory mapped I/O
xl0: Ethernet aCdodurledsns':t  0g0e:t0 1v:e0c2t:odrf :f1rco:mb 9I
SR!xl0: media options word: a
xl0: found MII/AUTO
xl0: bpf attached
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hatm0: <FORE HE> mem 0xf8000000-0xf80fffff irq 20 at device 8.0 on pci0
hatm0: carrier detected
hatm0: bpf attached
ioapic0: routing intpin 20 (IRQ 20) to cluster 0
hatm1: <FORE HE> mem 0xf6800000-0xf68fffff irq 17 at device 6.0 on pci2
pcib2: device hatm1 requested decoded memCooruyl drna'ntg eg e0tx fv6e8c0t0o0r0 0f-r0oxmf 6I8SfRf!fff
hatm1: hw.hatm1.rbps1_size=4096
hatm1: hw.hatm1.rbps1_thresh=2048
hatm1: hw.hatm1.tpdrq_size=4096
hatm1: hw.hatm1.tpdmax=0
hatm1: hw.hatm1.max_mbuf_pages=2048
hatm1: hw.hatm1.mpsafe=1
hatm1: carrier detected
hatm1: bpf attached
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
hatm2: <FORE HE> mem 0xf6000000-0xCfo6u0lfdfnf'ftf  giertq  v1e9ctor from ISR! at device 8.0 on pci2
pcib2: device hatm2 requested decoded memory range 0xf6000000-0xf60fffff
hatm2: hw.hatm2.rbps1_size=4096
hatm2: hw.hatm2.rbps1_thresh=2048
hatm2: hw.hatm2.tbrq0_size=8192
hatm2: hw.hatm2.tbrq0_thresh=6400
hatm2: hw.hatm2.tpdrq_size=4096
hatm2: hw.hatm2.tpdmax=0
hatm2: hw.hatm2.mpsCouldn't get vector from ISR!afe=1
hatm2: carrier detected
hatm2: bpf attached
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
hatm0: ForeRunnerHE 622, Rev. D, S/N 2949834, MAC=00:20:48:2d:02:ca (64bit PCI)
hatm1: ForeRunnerHE 155, Rev. B, S/N 3026384, MAC=00:20:48:2e:2d:d0 (32bit PCI)
hatm2: ForeRunnerHE 155, Rev. B, S/N 3027669, MAC=00:20:48:2e:32:d5 (32bit PCI)
hatm0: txmbuf leaves 0
-------------- next part --------------
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #32: Wed Nov  5 10:46:25 CET 2003
    hbb at beagle.fokus.fraunhofer.de:/opt/obj/usr/src/sys/MARIPOSA
Preloaded elf kernel "/boot/kernel/kernel" at 0xc06a4000.
Preloaded elf module "/boot/kernel/random.ko" at 0xc06a4278.
Calibrating clock(s) ... i8254 clock: 1193145 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1380008649 Hz
CPU: AMD Athlon(TM) MP 1800+ (1380.01-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x662  Stepping = 2
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0480000<MP,AMIE,DSP,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory  = 536788992 (511 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000829000 - 0x000000001f6c5fff, 518639616 bytes (126621 pages)
avail memory = 516005888 (492 MB)
MPTable: <ASUS     PROD00000000>
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
bios32: Found BIOS32 Service Directory header at 0xc00f2560
bios32: Entry = 0xf1d20 (c00f1d20)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x1f20
pnpbios: Found PnP BIOS data at 0xc00fc5e0
pnpbios: Entry = f0000:c610  Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
ioapic0: Assuming intbase of 0
ioapic0: intpin 0 -> ExtINT
ioapic0: intpin 1 -> irq 1
ioapic0: intpin 2 -> irq 2
ioapic0: intpin 3 -> irq 3
ioapic0: intpin 4 -> irq 4
ioapic0: intpin 5 -> irq 5
ioapic0: intpin 6 -> irq 6
ioapic0: intpin 7 -> irq 7
ioapic0: intpin 8 -> irq 8
ioapic0: intpin 9 -> irq 9
ioapic0: intpin 10 -> irq 10
ioapic0: intpin 11 -> irq 11
ioapic0: intpin 12 -> irq 12
ioapic0: intpin 13 -> irq 13
ioapic0: intpin 14 -> irq 14
ioapic0: intpin 15 -> irq 15
ioapic0: intpin 16 -> irq 16
ioapic0: intpin 17 -> irq 17
ioapic0: intpin 18 -> irq 18
ioapic0: intpin 19 -> irq 19
ioapic0: intpin 20 -> irq 20
ioapic0: intpin 21 -> irq 21
ioapic0: intpin 22 -> irq 22
ioapic0: intpin 23 -> irq 23
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: active-lo
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: active-lo
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: active-lo
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: active-lo
ioapic0: intpin 18 trigger: level
ioapic0: intpin 18 polarity: active-lo
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: active-lo
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: active-lo
ioapic0: intpin 1 trigger: edge
ioapic0: intpin 1 polarity: active-hi
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: active-hi
ioapic0: intpin 3 trigger: edge
ioapic0: intpin 3 polarity: active-hi
ioapic0: intpin 4 trigger: edge
ioapic0: intpin 4 polarity: active-hi
ioapic0: intpin 6 trigger: edge
ioapic0: intpin 6 polarity: active-hi
ioapic0: intpin 7 trigger: edge
ioapic0: intpin 7 polarity: active-hi
ioapic0: intpin 8 trigger: edge
ioapic0: intpin 8 polarity: active-hi
ioapic0: intpin 9 trigger: edge
ioapic0: intpin 9 polarity: active-hi
ioapic0: intpin 13 trigger: edge
ioapic0: intpin 13 polarity: active-hi
ioapic0: intpin 14 trigger: edge
ioapic0: intpin 14 polarity: active-hi
ioapic0: intpin 15 trigger: edge
ioapic0: intpin 15 polarity: active-hi
lapic: Routing ExtINT -> LINT0
lapic: LINT0 trigger: edge
lapic: LINT0 polarity: active-hi
lapic: Routing NMI -> LINT1
lapic: LINT1 trigger: edge
lapic: LINT1 polarity: active-hi
ioapic0 <Version 17> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
mem: <memory & I/O>
Pentium Pro MTRR support enabled
null: <null device, zero device>
random: <entropy source>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80012848
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=700c1022)
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00f24a0
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    7    B   0x01  3 4 5 7 9 10 11 12
embedded    0    7    C   0x02  3 4 5 7 9 10 11 12
embedded    0    7    D   0x03  3 4 5 7 9 10 11 12
slot 1      0    8    B   0x01  3 4 5 7 9 10 11 12
slot 1      0    8    C   0x02  3 4 5 7 9 10 11 12
slot 1      0    8    D   0x03  3 4 5 7 9 10 11 12
slot 2      0    9    A   0x01  3 4 5 7 9 10 11 12
slot 2      0    9    B   0x02  3 4 5 7 9 10 11 12
slot 2      0    9    C   0x03  3 4 5 7 9 10 11 12
slot 3      2    6    A   0x01  3 4 5 7 9 10 11 12
slot 3      2    6    B   0x02  3 4 5 7 9 10 11 12
slot 3      2    6    C   0x03  3 4 5 7 9 10 11 12
slot 4      2    5    A   0x02  3 4 5 7 9 10 11 12
slot 4      2    5    B   0x03  3 4 5 7 9 10 11 12
slot 4      2    5    D   0x01  3 4 5 7 9 10 11 12
slot 5      2    8    A   0x03  3 4 5 7 9 10 11 12
slot 5      2    8    C   0x01  3 4 5 7 9 10 11 12
slot 5      2    8    D   0x02  3 4 5 7 9 10 11 12
embedded    1    5    B   0x01  3 4 5 7 9 10 11 12
embedded    1    5    C   0x02  3 4 5 7 9 10 11 12
embedded    1    5    D   0x03  3 4 5 7 9 10 11 12
embedded    2    4    A   0x01  3 4 5 7 9 10 11 12
embedded    2    4    B   0x02  3 4 5 7 9 10 11 12
embedded    2    4    C   0x03  3 4 5 7 9 10 11 12
embedded    2    0    B   0x01  3 4 5 7 9 10 11 12
embedded    2    0    C   0x02  3 4 5 7 9 10 11 12
embedded    2    0    D   0x03  3 4 5 7 9 10 11 12
pcib0: <MPTable Host-PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
	map[10]: type 3, range 32, base fc000000, size 25, enabled
	map[14]: type 3, range 32, base fb800000, size 12, enabled
	map[18]: type 4, range 32, base 0000e800, size  2, port disabled
found->	vendor=0x1022, dev=0x700c, revid=0x11
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x700d, revid=0x00
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7440, revid=0x04
	bus=0, slot=7, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000d800, size  4, enabled
found->	vendor=0x1022, dev=0x7441, revid=0x04
	bus=0, slot=7, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7443, revid=0x03
	bus=0, slot=7, func=3
	class=06-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 1, range 32, base f8000000, size 20, enabled
pcib0: slot 8 INTA routed to irq 16
found->	vendor=0x1127, dev=0x0400, revid=0x00
	bus=0, slot=8, func=0
	class=02-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0016, statreg=0x0220, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x01 (250 ns)
	intpin=a, irq=16
found->	vendor=0x1022, dev=0x7448, revid=0x04
	bus=0, slot=16, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0017, statreg=0x2220, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
pcib1: <MPTable PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xe000-0xdfff
pcib1:   memory decode     0xf8800000-0xf9bfffff
pcib1:   prefetched decode 0xf9f00000-0xfb7fffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
	map[10]: type 3, range 32, base fa000000, size 24, enabled
	map[14]: type 1, range 32, base f9000000, size 14, enabled
	map[18]: type 1, range 32, base f8800000, size 23, enabled
pcib1: slot 5 INTA routed to irq 16
found->	vendor=0x102b, dev=0x0521, revid=0x01
	bus=1, slot=5, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x10 (4000 ns), maxlat=0x20 (8000 ns)
	intpin=a, irq=16
	powerspec 1  supports D0 D3  current D0
pci1: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 768 UDMA100 controller> port 0xd800-0xd80f at device 7.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave:  stat=0x00 err=0x04 lsb=0x7f msb=0x7f
ata1: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pci0: <network, ATM> at device 8.0 (no driver attached)
pcib2: <MPTable PCI-PCI bridge> at device 16.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xc000-0xcfff
pcib2:   memory decode     0xf6000000-0xf7ffffff
pcib2:   prefetched decode 0xf9c00000-0xf9dfffff
pci2: <PCI bus> on pcib2
pci2: physical bus=2
	map[10]: type 4, range 32, base 0000c800, size  8, enabled
pcib2: slot 4 INTA routed to irq 17
found->	vendor=0x13f6, dev=0x0111, revid=0x10
	bus=2, slot=4, func=0
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0085, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 0000c400, size  7, enabled
	map[14]: type 1, range 32, base f7000000, size  7, enabled
pcib2: slot 5 INTA routed to irq 18
found->	vendor=0x10b7, dev=0x9200, revid=0x74
	bus=2, slot=5, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base f6800000, size 20, enabled
pcib2: slot 6 INTA routed to irq 17
found->	vendor=0x1127, dev=0x0400, revid=0x01
	bus=2, slot=6, func=0
	class=02-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0016, statreg=0x0220, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x01 (250 ns)
	intpin=a, irq=17
	map[10]: type 1, range 32, base f6000000, size 20, enabled
pcib2: slot 8 INTA routed to irq 19
found->	vendor=0x1127, dev=0x0400, revid=0x01
	bus=2, slot=8, func=0
	class=02-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0016, statreg=0x0220, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x01 (250 ns)
	intpin=a, irq=19
pci2: <multimedia, audio> at device 4.0 (no driver attached)
pci2: <network, ethernet> at device 5.0 (no driver attached)
pci2: <network, ATM> at device 6.0 (no driver attached)
pci2: <network, ATM> at device 8.0 (no driver attached)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
pnpbios: 15 devices, largest 114 bytes
PNP0401: adding dma mask 0x8
PNP0401: adding irq mask 0x80
PNP0401: adding io range 0x378-0x37f, size=0x8, align=0
PNP0401: adding io range 0x778-0x77f, size=0x8, align=0
pnpbios: handle 1 device ID PNP0401 (0104d041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 2 device ID PNP0501 (0105d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
pnpbios: handle 3 device ID PNP0501 (0105d041)
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0
pnpbios: handle 4 device ID PNP0700 (0007d041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 5 device ID PNP0f13 (130fd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x1fffffff, size=0x1ff00000
PNP0c01: adding fixed memory32 range 0xe8000-0xeffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xc8800-0xcbfff, size=0x3800
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
pnpbios: handle 6 device ID PNP0c01 (010cd041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 8 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x75, size=0x6, align=0
pnpbios: handle 9 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 10 device ID PNP0303 (0303d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xf0, size=0x1, align=0
pnpbios: handle 11 device ID PNP0c04 (040cd041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x80-0x90, size=0x11, align=0
PNP0200: adding io range 0x94-0x9f, size=0xc, align=0
PNP0200: adding io range 0xc0-0xde, size=0x1f, align=0
pnpbios: handle 12 device ID PNP0200 (0002d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 13 device ID PNP0800 (0008d041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
pnpbios: handle 14 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0xe400-0xe47f, size=0x80, align=0
PNP0c02: adding io range 0xe4e0-0xe4ff, size=0x20, align=0
pnpbios: handle 15 device ID PNP0c02 (020cd041)
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc8000-0xc87ff,0xc0000-0xc7fff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0065
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0xe0c1 0xe0d1 0xe0c1 0xe0c1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0xe0c1 0xe0c9 0xe0c1 0xe0c1
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 50 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x378-0x37f on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
psmcpnp0: <PS/2 mouse port> at irq 12 on isa0
psm0: current command byte:0065
psm0: failed to reset the aux device.
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
speaker0: <PC speaker> at port 0x61 on isa0
Device configuration finished.
Timecounter "TSC" frequency 1380008649 Hz quality -100
Timecounters tick every 1.000Couldn't get vector from ISR! msec
lo0: bpf attached
ata0-master: pio=0Couldn't get vector from ISR!x0c wdma=0x22 uCouldn't get vector from ISR!dma=0x45 caCouldn't get vector from ISR!ble=80pin
ad0: setting UDMA100 on AMD 768 chip
GEOM: creatCouldn't get vector from ISR!e disk ad0 dp=0Couldn't get vector from ISR!xc629e970
ad0:Couldn't get vector from ISR! <ST340810A/3.3Couldn't get vector from ISR!9> ATA-6 disk aCouldn't get vector from ISR!t ata0-master
Couldn't get vector from ISR!ad0: 38166MB (7Couldn't get vector from ISR!8165360 sectorsCouldn't get vector from ISR!), 77545 C,Couldn't get vector from ISR! 16 H, 63 S, 512 BCouldn't get vector from ISR!
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
Couldn't get vector from ISR!ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
acd0: setting PICouldn't get vector from ISR!O4 on AMD 768 cCouldn't get vector from ISR!hip
acd0: <TOSCouldn't get vector from ISR!HIBA CD-ROMCouldn't get vector from ISR! XM-6702B/1005> CDRCouldn't get vector from ISR!OM drive at ataCouldn't get vector from ISR!1 as masterCouldn't get vector from ISR!
acd0: read 82Couldn't get vector from ISR!68KB/s (8268KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream
acd0: Writes:
acd0: Audio: play, 16 volume levels
acd0: MechanCouldn't get vector from ISR!ism: ejectable Couldn't get vector from ISR!tray, unlockedCouldn't get vector from ISR!
acd0: MediCouldn't get vector from ISR!um: no/blank disc
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
i[o0a]p ifc:08:0  rtoyupt:i1n6g5  isn(tCpHiSn) :10 /(1I/R1Q  e1(CCHoSu)l:d1n0'2t3 /g2e5t4 /v6e3c tso:r6 3f rlo:m7 8I1S5R6!)1 6t2o 
c[l1u]s tfe:r0 00 t
yipo:a0p si(cCHCSo)u:l0d/n0'/t0  gee(tC HvSe)c:t0o/r0 /f0r osm: 0I SlR:!00: 
r[o2u]t ifn:g0 0i nttyppi:n0  3s ((CIHRSQ) :03/)0 /t0o  ec(lCuHsSt)e:r0 /00/
0i osa:p0i cl0::0 r
o[u3t]i nfg: 0i0n ttpyipn: 04  s((ICRHQS) :40)/ 0t/o0  cel(uCsHtSe)r: 00/0/
0i osa:p0 ilc:00:
 routGiEnOgM :i nCtopnifni g6u r(eI RaQd 06s)1 ,t os tcalruts t3e2r2 506 
lieonagptihc 04:0 0r1o5u9t5i4n9g4 4i netnpdi n4 070 1(5I9R8Q7 179)9 t
o cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 13Couldn't get vector from ISR! (IRQ 13) to clCouldn't get vector from ISR!uster 0
ioapicCouldn't get vector from ISR!0: routing intpCouldn't get vector from ISR!in 14 (IRQ Couldn't get vector from ISR!14) to cluster Couldn't get vector from ISR!0
ioapic0: rouCouldn't get vector from ISR!ting intpin 15 (IRQ 15) to cluster 0
GEOM: Configure ad0s1a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s1b, start 268435456 length 1052180480 end 1320615935
GEOM: Configure ad0s1c, start 0 length 40015954944 end 40015954943
GEOM: Configure ad0s1d, start 1320615936 length 268435456 end 1589051391
GEOM: Configure ad0s1e, start 1589051392 length 268435456 end 1857486847
GEOM: Configure ad0s1f, start 1857486848 length 38158468096 end 40015954943
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xc400-0xc47f mem 0xf7000000-0xf700007f irq 18 at device 5.0 on pci2
pcib2: device xl0 requested decoded memory range 0xf7000000-0xf700007f
xl0: using memory mapped I/O
xl0: Ethernet address: 00:01:02:df:1c:b9
xl0: media options word: a
xl0: found MII/AUTO
xl0: bpf attached
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hatm0: <FORE HE> mem 0xf8000000-0xf80fffff irq 16 at device 8.0 on pci0
hatm0: carrier detected
hatm0: bpf attached
ioapic0: routing inCouldn't get vector from ISR!tpin 16 (IRQ 16) to cluster 0
hatm1: <FORE HE> mem 0xf6800000-0xf68fffff irq 17 at device 6.0 on pci2
pcib2: device hatm1 requested decoded memory range 0xf6800000-0xf68fffff
hatm1: hw.hatm1.rbps1_size=4096
hatm1: hw.hatm1.rbps1_thresh=2048
hatm1: hw.hatm1.tpdrq_size=4096
hatm1: hw.hatm1.tpdmax=0
hatm1: hw.hatm1.max_mbuf_pages=2048
hatm1: hw.hatm1.mpsafe=1
hatm1: carrier detCouldn't get vector from ISR!ected
hatm1: bpf attached
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
hatm2: <FORE HE> mem 0xf6000000-0xf60fffff irq 19 at device 8.0 on pci2
pcib2: device hatm2 requested decodCouldn't get vector from ISR!ed memory range 0xf6000000-0xf60fffff
hatm2: hw.hatm2.rbps1_size=4096
hatm2: hw.hatm2.rbps1_thresh=2048
hatm2: hw.hatm2.tbrq0_size=8192
hatm2: hw.hatm2.tbrq0_thresh=6400
hatm2: hw.hatm2.tpdrq_sizeC=o4u0l9d6n
'hta tgme2t:  vhewc.thoart mf2r.otmp dImSaRx!=0
hatm2: hw.hatm2.mpsafe=1
hatm2: carrier detected
hatm2: bpf attached
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
hatm0: ForeRunnerHE 622, Rev. D, S/N 2949834, MAC=00:20:48:2d:02:ca (64bit PCI)
hatm1: ForeRunnerHE 155, Rev. B, S/N 3026384, MAC=00:20:48:2e:2d:d0 (32bit PCI)
hatm2: ForeRunnerHE 155, Rev. B, S/N 3027669, MAC=00:20:48:2e:32:d5 (32bit PCI)
hatm0: txmbuf leaves 0


More information about the freebsd-current mailing list