5.1RC1 installation report

Thomas Girard nouvelles.fraiches at free.fr
Wed Jun 4 07:23:50 PDT 2003 

FreeBSD-current@,

Just to let you know that I've successfully installed FreeBSD/i386  5.1RC1 on 
a Sony Vaio PCG-GRX316G laptop. 

Before the instaIlation starts, I encountered a problem : after probing 
firewire hardware (I have an empty slot on the laptop), the kernel hung (I 
can repeat this every time by booting the install CD without pressing '6') 
with the following output :

fwohci0: Phy 1394 only S100, 0 ports.
fwohci0: fwphy_rddata: loop=100, retry=101
fwohci0: Link S100, max_rec 2 bytes.
fwohci0: max_rec 2 -> 512
firewire0: : <IEEE1394(FireWire) bus> on fwohci0


Fatal trap 12: page fault while in kernel mode
fault virtual address  = 0x2c
fault code                = supervisor read, page not present
instruction pointer    = 0x8:0xc02e5a40
stack pointer           = 0x10:0xc0b2e8c4
frame pointer          = 0x10:0xc0b2e8c8
code segment         = base 0x0, limit 0xfffff, type 0x1b
                              = DPL 0, pres 1, def32 1, gran 1
processor eflags      = interrupt enabled, resume, IOPL = 0
current process       = 0 (swapper)
trap number            = 12
panic: page fault
Terminate ACPI

I solved this by setting hw.pci.allow_unsupported_io_range=1 with the loader. 
After that, the whole installation process went well. I've noticed that the 
output of dmesg now reads :
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.

Was there another workaround ? I tried disabling ACPI, setting 
hint.firewire.0.disabled=1 or hint.fwohci.0.disabled=1 and none of these 
worked. Then I read loader(8).

Hope this helps,
Thomas
-------------- next part --------------
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RC1 #0: Sun Jun  1 04:55:11 GMT 2003
    root at wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc06d4000.
Preloaded elf module "/boot/kernel.old/acpi.ko" at 0xc06d4298.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 1590814848 Hz
CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.60GHz (1590.81-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf24  Stepping = 4
  Features=0x3febf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
real memory  = 267911168 (255 MB)
avail memory = 252776448 (241 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY B0> on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00fdf50
    ACPI-0351: *** Error: Could not install PciConfig handler for PCI0, AE_ALREADY_EXISTS
    ACPI-0351: *** Error: Could not install PciConfig handler for PCI0, AE_ALREADY_EXISTS
    ACPI-0351: *** Error: Could not install PciConfig handler for PCI0, AE_ALREADY_EXISTS
Timecounter "ACPI-fast"  frequency 3579545 Hz
    ACPI-0351: *** Error: Could not install PciConfig handler for PCI0, AE_ALREADY_EXISTS
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82845 host to AGP bridge> mem 0xec000000-0xefffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 9 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq 9 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f at device 29.2 on pci0
pcib0: possible interrupts:  9
pcib0: slot 29 INTC routed to irq 9 via \\_SB_.LNKC
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
umass0: Sony USB Memory Stick Slot, rev 1.10/1.07, addr 2
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
cbb0: <RF5C476 PCI-CardBus Bridge> irq 3 at device 5.0 on pci2
start (88000000) < sc->membase (e8200000)
end (ffffffff) > sc->memlimit (e82fffff)
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <RF5C476 PCI-CardBus Bridge> at device 5.1 on pci2
start (88000000) < sc->membase (e8200000)
end (ffffffff) > sc->memlimit (e82fffff)
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib2: possible interrupts:  9
pcib2: slot 5 INTB routed to irq 9 via \\_SB_.LNKG
fwohci0: <Ricoh R5C552> mem 0xe8201000-0xe82017ff at device 5.2 on pci2
pcib2: possible interrupts:  9
pcib2: slot 5 INTC routed to irq 9 via \\_SB_.LNKH
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 08:00:46:03:01:10:bb:6a
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
if_fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 0a:00:46:10:bb:6a
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x4000-0x403f mem 0xe8200000-0xe8200fff irq 9 at device 8.0 on pci2
fxp0: Ethernet address 08:00:46:63:af:68
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xe8000000-0xe80003ff at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcffff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ad0: 19077MB <IC25N020ATCS04-0> [38760/16/63] at ata0-master UDMA100
acd0: CD-RW <SONY CD-RW/DVD-ROM CRX810E> at ata1-master PIO4
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_.BAT1._STA] (Node 0xc261ba00), AE_ERROR
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_.BAT1._STA] (Node 0xc261ba00), AE_ERROR
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_.ACAD._PSR] (Node 0xc261b820), AE_ERROR
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:0): Medium not present
(probe0:umass-sim0:0:0:0): Unretryable error
Mounting root from ufs:/dev/ad0s3a
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_TZ_.ATF0._TMP] (Node 0xc261d280), AE_ERROR

More information about the freebsd-current mailing list