[Bug 200993] camcontrol commands results in Periph destroyed on mrsas
bugzilla-noreply at freebsd.org
bugzilla-noreply at freebsd.org
Wed Jul 6 19:17:15 UTC 2016
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=200993
emz at norma.perm.ru changed:
What |Removed |Added
----------------------------------------------------------------------------
CC| |emz at norma.perm.ru
--- Comment #12 from emz at norma.perm.ru ---
Same stuff here. camcontrol identify doesn't lead to topology change, but
smartctl -a definitely does. This is reproducible on a fresh 11.[ and 10.3.
Controller:
LSI MegaRAID SAS 9341-4i
Firmware:
Product Name : LSI MegaRAID SAS 9341-4i
Serial No : SV62122829
FW Package Build: 24.2.1-0021
Console log:
[root at san1:/etc]# zpool status
pool: esx
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: scrub repaired 0 in 5h40m with 0 errors on Tue Jun 28 03:27:20 2016
config:
NAME STATE READ WRITE CKSUM
esx ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da3 ONLINE 0 0 0
da4 ONLINE 0 0 0
mirror-1 ONLINE 0 0 0
da6 ONLINE 0 0 0
da7 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
da9 ONLINE 0 0 0
da10 ONLINE 0 0 0
mirror-3 ONLINE 0 0 0
da12 ONLINE 0 0 0
da13 ONLINE 0 0 0
mirror-4 ONLINE 0 0 0
da5 ONLINE 0 0 0
da8 ONLINE 0 0 0
mirror-5 ONLINE 0 0 0
da11 ONLINE 0 0 0
da14 ONLINE 0 0 0
mirror-6 ONLINE 0 0 0
da15 ONLINE 0 0 0
da16 ONLINE 0 0 0
errors: No known data errors
pool: gamestop
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: resilvered 729M in 0h0m with 0 errors on Thu Jul 7 04:02:53 2016
config:
NAME STATE READ WRITE CKSUM
gamestop ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da0 ONLINE 0 0 0
da17 ONLINE 0 0 0
mirror-1 ONLINE 0 0 0
da18 ONLINE 0 0 0
da19 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
da20 ONLINE 0 0 0
da21 ONLINE 0 0 0
mirror-3 ONLINE 0 0 0
da22 ONLINE 0 0 0
da23 ONLINE 0 0 0
errors: No known data errors
pool: zroot
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: scrub repaired 0 in 0h1m with 0 errors on Mon Jun 27 21:21:40 2016
config:
NAME STATE READ WRITE CKSUM
zroot ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da1p3 ONLINE 0 0 0
da2p3 ONLINE 0 0 0
errors: No known data errors
[root at san1:/etc]# smartctl -a /dev/da2
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-ALPHA5 amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST2000NX0253
Serial Number: S460ED5C
LU WWN Device Id: 5 000c50 08ca8b9aa
Firmware Version: SN02
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jul 7 03:04:27 2016 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: Input/output error
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 330) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 081 063 044 Pre-fail Always
- 134895728
3 Spin_Up_Time 0x0003 092 092 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
- 22
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always
- 8
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always
- 19270762
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 624
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 22
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 068 067 040 Old_age Always
- 32 (Min/Max 20/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 7
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always
- 1280
194 Temperature_Celsius 0x0022 032 040 000 Old_age Always
- 32 (0 12 0 0 0)
195 Hardware_ECC_Recovered 0x001a 005 004 000 Old_age Always
- 134895728
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
Read SMART Log Directory failed: Input/output error
Read SMART Error Log failed: Input/output error
Read SMART Self-test Log failed: Input/output error
Read SMART Selective Self-test Log failed: Input/output error
[root at san1:/etc]# dmesg
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-ALPHA5 #1: Thu Jun 30 22:56:33 MSK 2016
emz at san1:/usr/obj/usr/src/sys/SAN amd64
[...]
da2 at mrsas0 bus 1 scbus1 target 7 lun 0
da2: <ATA ST2000NX0253 SN02> s/n S460ED5C detached
GEOM_MIRROR: Device swap: provider da2p2 disconnected.
[root at san1:/etc]# camcontrol rescan 1:7:0
Re-scan of 1:7:0 was successful
[root at san1:/etc]# zpool status
pool: esx
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: scrub repaired 0 in 5h40m with 0 errors on Tue Jun 28 03:27:20 2016
config:
NAME STATE READ WRITE CKSUM
esx ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da3 ONLINE 0 0 0
da4 ONLINE 0 0 0
mirror-1 ONLINE 0 0 0
da6 ONLINE 0 0 0
da7 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
da9 ONLINE 0 0 0
da10 ONLINE 0 0 0
mirror-3 ONLINE 0 0 0
da12 ONLINE 0 0 0
da13 ONLINE 0 0 0
mirror-4 ONLINE 0 0 0
da5 ONLINE 0 0 0
da8 ONLINE 0 0 0
mirror-5 ONLINE 0 0 0
da11 ONLINE 0 0 0
da14 ONLINE 0 0 0
mirror-6 ONLINE 0 0 0
da15 ONLINE 0 0 0
da16 ONLINE 0 0 0
errors: No known data errors
pool: gamestop
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: resilvered 729M in 0h0m with 0 errors on Thu Jul 7 04:02:53 2016
config:
NAME STATE READ WRITE CKSUM
gamestop ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da0 ONLINE 0 0 0
da17 ONLINE 0 0 0
mirror-1 ONLINE 0 0 0
da18 ONLINE 0 0 0
da19 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
da20 ONLINE 0 0 0
da21 ONLINE 0 0 0
mirror-3 ONLINE 0 0 0
da22 ONLINE 0 0 0
da23 ONLINE 0 0 0
errors: No known data errors
pool: zroot
state: DEGRADED
status: One or more devices has been removed by the administrator.
Sufficient replicas exist for the pool to continue functioning in a
degraded state.
action: Online the device using 'zpool online' or replace the device with
'zpool replace'.
scan: scrub repaired 0 in 0h1m with 0 errors on Mon Jun 27 21:21:40 2016
config:
NAME STATE READ WRITE CKSUM
zroot DEGRADED 0 0 0
mirror-0 DEGRADED 0 0 0
da1p3 ONLINE 0 0 0
17040910893353730136 REMOVED 0 0 0 was /dev/da2p3
errors: No known data errors
[root at san1:/etc]# zpool online zroot da2p3
[root at san1:/etc]# zpool status
pool: esx
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: scrub repaired 0 in 5h40m with 0 errors on Tue Jun 28 03:27:20 2016
config:
NAME STATE READ WRITE CKSUM
esx ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da3 ONLINE 0 0 0
da4 ONLINE 0 0 0
mirror-1 ONLINE 0 0 0
da6 ONLINE 0 0 0
da7 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
da9 ONLINE 0 0 0
da10 ONLINE 0 0 0
mirror-3 ONLINE 0 0 0
da12 ONLINE 0 0 0
da13 ONLINE 0 0 0
mirror-4 ONLINE 0 0 0
da5 ONLINE 0 0 0
da8 ONLINE 0 0 0
mirror-5 ONLINE 0 0 0
da11 ONLINE 0 0 0
da14 ONLINE 0 0 0
mirror-6 ONLINE 0 0 0
da15 ONLINE 0 0 0
da16 ONLINE 0 0 0
errors: No known data errors
pool: gamestop
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: resilvered 729M in 0h0m with 0 errors on Thu Jul 7 04:02:53 2016
config:
NAME STATE READ WRITE CKSUM
gamestop ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da0 ONLINE 0 0 0
da17 ONLINE 0 0 0
mirror-1 ONLINE 0 0 0
da18 ONLINE 0 0 0
da19 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
da20 ONLINE 0 0 0
da21 ONLINE 0 0 0
mirror-3 ONLINE 0 0 0
da22 ONLINE 0 0 0
da23 ONLINE 0 0 0
errors: No known data errors
pool: zroot
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: resilvered 16K in 0h0m with 0 errors on Thu Jul 7 03:05:18 2016
config:
NAME STATE READ WRITE CKSUM
zroot ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
da1p3 ONLINE 0 0 0
da2p3 ONLINE 0 0 0
errors: No known data errors
[root at san1:/etc]#
--
You are receiving this mail because:
You are the assignee for the bug.
More information about the freebsd-bugs
mailing list