misc/182141: Very frequent (at most 3 hours) kernel trap 12

Wed Sep 18 09:50:06 UTC 2013

The following reply was made to PR misc/182141; it has been noted by GNATS.

From: Berend de Boer <berend at pobox.com>
To: bug-followup at FreeBSD.org, berend at pobox.com
Cc:  
Subject: Re: misc/182141: Very frequent (at most 3 hours) kernel trap 12
Date: Wed, 18 Sep 2013 21:39:35 +1200

 This is an OpenPGP/MIME signed message (RFC 4880 and 3156)
 --9qfsKgCMUbdjOVQRWvcgIrPbUjrRqdolN
 Content-Type: text/plain; charset=ISO-8859-1
 Content-Transfer-Encoding: quoted-printable

 As requested by freebsdhelp: revision updated to is latest (retrieved
 using cvsup): default release=3Dcvs tag=3DRELENG_9

 /var/run/dmesg.boot:

 fxp0: Ethernet address: 00:90:27:17:93:5d
 fwohci0: <Texas Instruments TSB43AB22/A> mem
 0xe3344000-0xe33447ff,0xe3340000-0xe3343fff irq 19 at device 3.0 on pci7
 fwohci0: OHCI version 1.10 (ROM=3D0)
 fwohci0: No. of Isochronous channels is 4.
 fwohci0: EUI64 00:90:27:00:01:df:6e:98
 fwohci0: Phy 1394a available S400, 2 ports.
 fwohci0: Link S400, max_rec 2048 bytes.
 firewire0: <IEEE1394(FireWire) bus> on fwohci0
 fwe0: <Ethernet over FireWire> on firewire0
 if_fwe0: Fake Ethernet address: 02:90:27:df:6e:98
 fwe0: Ethernet address: 02:90:27:df:6e:98
 fwip0: <IP over FireWire> on firewire0
 fwip0: Firewire address: 00:90:27:00:01:df:6e:98 @ 0xfffe00000000, S400,
 maxrec 2048
 dcons_crom0: <dcons configuration ROM> on firewire0
 dcons_crom0: bus_addr 0x145c000
 fwohci0: Initiate bus reset
 fwohci0: fwohci_intr_core: BUS reset
 fwohci0: fwohci_intr_core: node_id=3D0x00000000, SelfID Count=3D1,
 CYCLEMASTER mode
 isab0: <PCI-ISA bridge> at device 31.0 on pci0
 isa0: <ISA bus> on isab0
 ahci0: <Intel ICH8 AHCI SATA controller> port
 0x5408-0x540f,0x5414-0x5417,0x5400-0x5407,0x5410-0x5413,0x5020-0x503f
 mem 0xe3525000-0xe35257ff irq 19 at device 31.2 on pci0
 ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier not supported
 ahcich0: <AHCI channel> at channel 0 on ahci0
 ahcich1: <AHCI channel> at channel 1 on ahci0
 ahcich4: <AHCI channel> at channel 4 on ahci0
 ahcich5: <AHCI channel> at channel 5 on ahci0
 pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
 ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
 ppc0: FIFO with 16/16/8 bytes threshold
 ppbus0: <Parallel port bus> on ppc0
 plip0: <PLIP network interface> on ppbus0
 lpt0: <Printer> on ppbus0
 lpt0: Interrupt-driven port
 ppi0: <Parallel I/O> on ppbus0
 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
 atkbd0: <AT Keyboard> irq 1 on atkbdc0
 kbd0 at atkbd0
 atkbd0: [GIANT-LOCKED]
 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
 pmtimer0 on isa0
 orm0: <ISA Option ROMs> at iomem 0xcf800-0xd07ff,0xd0800-0xd0fff pnpid
 ORM0000 on isa0
 sc0: <System console> at flags 0x100 on isa0
 sc0: VGA <16 virtual consoles, flags=3D0x300>
 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0=

 ata0: <ATA channel> at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
 ata1: <ATA channel> at port 0x170-0x177,0x376 irq 15 on isa0
 est0: <Enhanced SpeedStep Frequency Control> on cpu0
 p4tcc0: <CPU Frequency Thermal Control> on cpu0
 est1: <Enhanced SpeedStep Frequency Control> on cpu1
 p4tcc1: <CPU Frequency Thermal Control> on cpu1
 firewire0: 1 nodes, maxhop <=3D 0 cable IRM irm(0)  (me)
 firewire0: bus manager 0
 Timecounters tick every 1.000 msec
 hdacc0: <Sigmatel STAC9227X HDA CODEC> at cad 2 on hdac0
 hdaa0: <Sigmatel STAC9227X Audio Function Group> at nid 1 on hdacc0
 pcm0: <Sigmatel STAC9227X (Analog 5.1+HP/2.0)> at nid 13,15,14,10 and 11
 on hdaa0
 usbus0: 12Mbps Full Speed USB v1.0
 usbus1: 12Mbps Full Speed USB v1.0
 usbus2: 480Mbps High Speed USB v2.0
 usbus3: 12Mbps Full Speed USB v1.0
 usbus4: 12Mbps Full Speed USB v1.0
 usbus5: 12Mbps Full Speed USB v1.0
 usbus6: 480Mbps High Speed USB v2.0
 ugen0.1: <Intel> at usbus0
 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
 ugen1.1: <Intel> at usbus1
 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
 ugen2.1: <Intel> at usbus2
 uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
 ugen3.1: <Intel> at usbus3
 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
 ugen4.1: <Intel> at usbus4
 uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
 ugen5.1: <Intel> at usbus5
 uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
 ugen6.1: <Intel> at usbus6
 uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
 uhub0: 2 ports with 2 removable, self powered
 uhub1: 2 ports with 2 removable, self powered
 uhub3: 2 ports with 2 removable, self powered
 uhub4: 2 ports with 2 removable, self powered
 uhub5: 2 ports with 2 removable, self powered
 uhub2: 4 ports with 4 removable, self powered
 uhub6: 6 ports with 6 removable, self powered
 ugen2.2: <Hewlett-Packard> at usbus2
 ulpt0: <Printer> on usbus2
 ulpt0: using bi-directional mode
 ugen3.2: <vendor 0x0001> at usbus3
 uhid0: <vendor 0x0001 product 0x0000, class 0/0, rev 1.00/1.00, addr 2>
 on usbus3
 ugen2.3: <Sunplus Technology Inc.> at usbus2
 umass0: <Bulk Only Interface> on usbus2
 umass0:  SCSI over Bulk-Only; quirks =3D 0x4101
 umass0:10:0:-1: Attached to scbus10
 sa0 at ahc1 bus 0 scbus2 target 6 lun 0
 sa0: <SEAGATE DAT    9SP40-000 910B> Removable Sequential Access SCSI-3
 device
 sa0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
 ada0 at ata2 bus 0 scbus0 target 0 lun 0
 ada0: <ST3160815A 3.AAD> ATA-7 device
 ada0: 100.000MB/s transfers (UDMA5, PIO 8192bytes)
 ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
 ada0: Previously was known as ad4
 cd0 at ata2 bus 0 scbus0 target 1 lun 0
 cd0: <Optiarc DVD RW AD-7170A 1.85> Removable CD-ROM SCSI-0 device
 cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes)
 cd0: cd present [292819 x 2048 byte records]
 da0 at umass-sim0 bus 0 scbus10 target 0 lun 0
 da0: <Hitachi HTS721010G9SA00 > Fixed Direct Access SCSI-2 device
 da0: 40.000MB/s transfers
 da0: 95396MB (195371568 512 byte sectors: 255H 63S/T 12161C)
 ada1 at ahcich0 bus 0 scbus3 target 0 lun 0
 ada1: <ST500DM002-1BD142 KC44> ATA-8 SATA 3.x device
 ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
 ada1: Command Queueing enabled
 ada1: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C)
 ada1: Previously was known as ad6
 SMP: AP CPU #1 Launched!
 Timecounter "TSC-low" frequency 15609752 Hz quality 1000
 (cd0:ata2:0:1:0): READ(10). CDB: 28 0 0 4 77 d2 0 0 1 0
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 0 0 4 77 d2 0 0 1 0
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 0 0 4 77 d2 0 0 1 0
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 0 0 4 77 d2 0 0 1 0
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 0 0 4 77 d2 0 0 1 0
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 0 0 4 77 d2 0 0 1 0
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 0 0 4 77 d2 0 0 1 0
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 Trying to mount root from cd9660:/dev/iso9660/FREEBSD_INSTALL [ro]...
 WARNING: / was not properly dismounted
 Waiting (max 60 seconds) for system process `vnlru' to stop...done
 Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
 Waiting (max 60 seconds) for system process `syncer' to stop...
 Syncing disks, vnodes remaining...0 done
 All buffers synced.
 Uptime: 13m53s
 usbus0: Controller shutdown
 uhub0: at usbus0, port 1, addr 1 (disconnected)
 usbus0: Controller shutdown complete
 usbus1: Controller shutdown
 uhub1: at usbus1, port 1, addr 1 (disconnected)
 usbus1: Controller shutdown complete
 usbus2: Controller shutdown
 uhub2: at usbus2, port 1, addr 1 (disconnected)
 ugen2.2: <Hewlett-Packard> at usbus2 (disconnected)
 ulpt0: at uhub2, port 3, addr 2 (disconnected)
 ugen2.3: <Sunplus Technology Inc.> at usbus2 (disconnected)
 umass0: at uhub2, port 4, addr 3 (disconnected)
 (da0:umass-sim0:0:0:0): lost device - 0 outstanding, 1 refs
 (pass4:(da0:umass-sim0:0:umass-sim0:0:0:0:0): passdevgonecb: devfs entry
 is gone
 0): removing device entry
 usbus2: Controller shutdown complete
 usbus3: Controller shutdown
 uhub3: at usbus3, port 1, addr 1 (disconnected)
 ugen3.2: <vendor 0x0001> at usbus3 (disconnected)
 uhid0: at uhub3, port 2, addr 2 (disconnected)
 usbus3: Controller shutdown complete
 usbus4: Controller shutdown
 uhub4: at usbus4, port 1, addr 1 (disconnected)
 usbus4: Controller shutdown complete
 usbus5: Controller shutdown
 uhub5: at usbus5, port 1, addr 1 (disconnected)
 usbus5: Controller shutdown complete
 usbus6: Controller shutdown
 uhub6: at usbus6, port 1, addr 1 (disconnected)
 usbus6: Controller shutdown complete
 Rebooting...
 cpu_reset: Stopping other CPUs
 Copyright (c) 1992-2013 The FreeBSD Project.
 Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 	The Regents of the University of California. All rights reserved.
 FreeBSD is a registered trademark of The FreeBSD Foundation.
 FreeBSD 9.2-PRERELEASE #26: Wed Sep 18 11:37:44 NZST 2013
     root at bmach.nederware.nl:/usr/obj/usr/src/sys/BMACH i386
 gcc version 4.2.1 20070831 patched [FreeBSD]
 link_elf: symbol ata_controlcmd undefined
 KLD file atapicam.ko - could not finalize loading
 CPU: Intel(R) Core(TM)2 CPU          4400  @ 2.00GHz (1998.04-MHz
 686-class CPU)
   Origin =3D "GenuineIntel"  Id =3D 0x6f2  Family =3D 0x6  Model =3D 0xf
 Stepping =3D 2

 Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PG=
 E,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
   Features2=3D0xe39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM>=

   AMD Features=3D0x20100000<NX,LM>
   AMD Features2=3D0x1<LAHF>
   TSC: P-state invariant, performance statistics
 real memory  =3D 4294967296 (4096 MB)
 avail memory =3D 3399114752 (3241 MB)
 Event timer "LAPIC" quality 400
 ACPI APIC Table: <INTEL  DP965LT >
 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 FreeBSD/SMP: 1 package(s) x 2 core(s)
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
 ioapic0: Changing APIC ID to 2
 ioapic0 <Version 2.0> irqs 0-23 on motherboard
 kbd1 at kbdmux0
 cryptosoft0: <software crypto> on motherboard
 acpi0: <INTEL DP965LT> on motherboard
 acpi0: Power Button (fixed)
 cpu0: <ACPI CPU> on acpi0
 cpu1: <ACPI CPU> on acpi0
 atrtc0: <AT realtime clock> port 0x70-0x71,0x74-0x77 irq 8 on acpi0
 Event timer "RTC" frequency 32768 Hz quality 0
 attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
 Timecounter "i8254" frequency 1193182 Hz quality 0
 Event timer "i8254" frequency 1193182 Hz quality 100
 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed03fff on acpi0
 Timecounter "HPET" frequency 14318180 Hz quality 950
 Event timer "HPET" frequency 14318180 Hz quality 450
 Event timer "HPET1" frequency 14318180 Hz quality 440
 Event timer "HPET2" frequency 14318180 Hz quality 440
 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
 acpi_button0: <Sleep Button> on acpi0
 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
 pci0: <ACPI PCI bus> on pcib0
 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
 pci1: <ACPI PCI bus> on pcib1
 vgapci0: <VGA-compatible display> port 0x4000-0x407f mem
 0xe2000000-0xe2ffffff,0xd0000000-0xdfffffff,0xe0000000-0xe1ffffff irq 16
 at device 0.0 on pci1
 pci0: <simple comms> at device 3.0 (no driver attached)
 em0: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x50e0-0x50ff mem
 0xe3500000-0xe351ffff,0xe3524000-0xe3524fff irq 20 at device 25.0 on pci0=

 em0: Using an MSI interrupt
 em0: Ethernet address: 00:19:d1:e8:c7:b3
 uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x50c0-0x50df irq
 16 at device 26.0 on pci0
 uhci0: LegSup =3D 0x2f00
 usbus0 on uhci0
 uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x50a0-0x50bf irq
 21 at device 26.1 on pci0
 uhci1: LegSup =3D 0x2f00
 usbus1 on uhci1
 ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem
 0xe3525c00-0xe3525fff irq 18 at device 26.7 on pci0
 usbus2: EHCI version 1.0
 usbus2 on ehci0
 hdac0: <Intel 82801H HDA Controller> mem 0xe3520000-0xe3523fff irq 22 at
 device 27.0 on pci0
 pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
 pci2: <ACPI PCI bus> on pcib2
 pcib3: <ACPI PCI-PCI bridge> at device 28.1 on pci0
 pci3: <ACPI PCI bus> on pcib3
 atapci0: <Marvell 88SE6101 UDMA133 controller> port
 0x3018-0x301f,0x3024-0x3027,0x3010-0x3017,0x3020-0x3023,0x3000-0x300f
 mem 0xe3400000-0xe34001ff irq 17 at device 0.0 on pci3
 ata2: <ATA channel> at channel 0 on atapci0
 pcib4: <ACPI PCI-PCI bridge> at device 28.2 on pci0
 pci4: <ACPI PCI bus> on pcib4
 pcib5: <ACPI PCI-PCI bridge> at device 28.3 on pci0
 pci5: <ACPI PCI bus> on pcib5
 pcib6: <ACPI PCI-PCI bridge> at device 28.4 on pci0
 pci6: <ACPI PCI bus> on pcib6
 uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x5080-0x509f irq
 23 at device 29.0 on pci0
 uhci2: LegSup =3D 0x2f00
 usbus3 on uhci2
 uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x5060-0x507f irq
 19 at device 29.1 on pci0
 uhci3: LegSup =3D 0x2f00
 usbus4 on uhci3
 uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x5040-0x505f irq
 18 at device 29.2 on pci0
 uhci4: LegSup =3D 0x2f00
 usbus5 on uhci4
 ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem
 0xe3525800-0xe3525bff irq 23 at device 29.7 on pci0
 usbus6: EHCI version 1.0
 usbus6 on ehci1
 pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
 pci7: <ACPI PCI bus> on pcib7
 em1: <Intel(R) PRO/1000 Legacy Network Connection 1.0.6> port
 0x2000-0x203f mem 0xe3320000-0xe333ffff,0xe3300000-0xe331ffff irq 21 at
 device 0.0 on pci7
 em1: Ethernet address: 00:1b:21:51:e1:e0
 pcib8: <PCI-PCI bridge> at device 1.0 on pci7
 pci8: <PCI bus> on pcib8
 ahc0: <Adaptec 3940 Ultra SCSI adapter> port 0x1400-0x14ff mem
 0xe3201000-0xe3201fff irq 22 at device 4.0 on pci8
 aic7880: Ultra Wide Channel A, SCSI Id=3D7, 16/253 SCBs
 ahc1: <Adaptec 3940 Ultra SCSI adapter> port 0x1000-0x10ff mem
 0xe3200000-0xe3200fff irq 21 at device 5.0 on pci8
 aic7880: Ultra Wide Channel B, SCSI Id=3D0, 16/253 SCBs
 fxp0: <Intel 82558 Pro/100 Ethernet> port 0x2040-0x205f mem
 0xe3000000-0xe3000fff,0xe3100000-0xe31fffff irq 18 at device 2.0 on pci7
 miibus0: <MII bus> on fxp0
 inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
 inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
 fxp0: Ethernet address: 00:90:27:17:93:5d
 pci7: <serial bus, FireWire> at device 3.0 (no driver attached)
 isab0: <PCI-ISA bridge> at device 31.0 on pci0
 isa0: <ISA bus> on isab0
 ahci0: <Intel ICH8 AHCI SATA controller> port
 0x5408-0x540f,0x5414-0x5417,0x5400-0x5407,0x5410-0x5413,0x5020-0x503f
 mem 0xe3525000-0xe35257ff irq 19 at device 31.2 on pci0
 ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier not supported
 ahcich0: <AHCI channel> at channel 0 on ahci0
 ahcich1: <AHCI channel> at channel 1 on ahci0
 ahcich4: <AHCI channel> at channel 4 on ahci0
 ahcich5: <AHCI channel> at channel 5 on ahci0
 pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
 ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
 ppc0: FIFO with 16/16/8 bytes threshold
 ppbus0: <Parallel port bus> on ppc0
 plip0: <PLIP network interface> on ppbus0
 lpt0: <Printer> on ppbus0
 lpt0: Interrupt-driven port
 ppi0: <Parallel I/O> on ppbus0
 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
 atkbd0: <AT Keyboard> irq 1 on atkbdc0
 kbd0 at atkbd0
 atkbd0: [GIANT-LOCKED]
 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
 ichwd0 on isa0
 pmtimer0 on isa0
 orm0: <ISA Option ROMs> at iomem 0xcf800-0xd07ff,0xd0800-0xd0fff pnpid
 ORM0000 on isa0
 sc0: <System console> at flags 0x100 on isa0
 sc0: VGA <16 virtual consoles, flags=3D0x300>
 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0=

 ata0: <ATA channel> at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
 ata1: <ATA channel> at port 0x170-0x177,0x376 irq 15 on isa0
 coretemp0: <CPU On-Die Thermal Sensors> on cpu0
 est0: <Enhanced SpeedStep Frequency Control> on cpu0
 p4tcc0: <CPU Frequency Thermal Control> on cpu0
 coretemp1: <CPU On-Die Thermal Sensors> on cpu1
 est1: <Enhanced SpeedStep Frequency Control> on cpu1
 p4tcc1: <CPU Frequency Thermal Control> on cpu1
 Timecounters tick every 1.000 msec
 vboxdrv: fAsync=3D0 offMin=3D0x1e0 offMax=3D0x46a
 IPsec: Initialized Security Association Processing.
 ipfw2 (+ipv6) initialized, divert enabled, nat enabled, default to deny,
 logging disabled
 DUMMYNET 0 with IPv6 initialized (100409)
 load_dn_sched dn_sched FIFO loaded
 load_dn_sched dn_sched PRIO loaded
 load_dn_sched dn_sched QFQ loaded
 load_dn_sched dn_sched RR loaded
 load_dn_sched dn_sched WF2Q+ loaded
 hdacc0: <Sigmatel STAC9227X HDA CODEC> at cad 2 on hdac0
 hdaa0: <Sigmatel STAC9227X Audio Function Group> at nid 1 on hdacc0
 pcm0: <Sigmatel STAC9227X (Analog 5.1+HP/2.0)> at nid 13,15,14,10 and 11
 on hdaa0
 usbus0: 12Mbps Full Speed USB v1.0
 usbus1: 12Mbps Full Speed USB v1.0
 usbus2: 480Mbps High Speed USB v2.0
 usbus3: 12Mbps Full Speed USB v1.0
 usbus4: 12Mbps Full Speed USB v1.0
 usbus5: 12Mbps Full Speed USB v1.0
 usbus6: 480Mbps High Speed USB v2.0
 ugen0.1: <Intel> at usbus0
 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
 ugen1.1: <Intel> at usbus1
 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
 ugen2.1: <Intel> at usbus2
 uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
 ugen3.1: <Intel> at usbus3
 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
 ugen4.1: <Intel> at usbus4
 uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
 ugen5.1: <Intel> at usbus5
 uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
 ugen6.1: <Intel> at usbus6
 uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
 uhub0: 2 ports with 2 removable, self powered
 uhub1: 2 ports with 2 removable, self powered
 uhub3: 2 ports with 2 removable, self powered
 uhub4: 2 ports with 2 removable, self powered
 uhub5: 2 ports with 2 removable, self powered
 uhub2: 4 ports with 4 removable, self powered
 uhub6: 6 ports with 6 removable, self powered
 ugen2.2: <Hewlett-Packard> at usbus2
 ulpt0: <Printer> on usbus2
 ulpt0: using bi-directional mode
 ugen3.2: <vendor 0x0001> at usbus3
 uhid0: <vendor 0x0001 product 0x0000, class 0/0, rev 1.00/1.00, addr 2>
 on usbus3
 ugen2.3: <Sunplus Technology Inc.> at usbus2
 umass0: <Bulk Only Interface> on usbus2
 umass0:  SCSI over Bulk-Only; quirks =3D 0x4101
 umass0:9:0:-1: Attached to scbus9
 sa0 at ahc1 bus 0 scbus2 target 6 lun 0
 sa0: <SEAGATE DAT    9SP40-000 910B> Removable Sequential Access SCSI-3
 device
 sa0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
 ada0 at ata2 bus 0 scbus0 target 0 lun 0
 ada0: da0 at umass-sim0 bus 0 scbus9 target 0 lun 0
 <ST3160815A 3.AAD> ATA-7 device
 ada0: 100.000MB/s transfers (UDMA5, PIO 8192bytes)
 ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
 ada0: Previously was known as ad4
 cd0 at ata2 bus 0 scbus0 target 1 lun 0
 cd0: <Optiarc DVD RW AD-7170A 1.85> Removable CD-ROM SCSI-0 device
 cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes)
 cd0: cd present [292819 x 2048 byte records]
 da0: <Hitachi HTS721010G9SA00 > Fixed Direct Access SCSI-2 device
 da0: 40.000MB/s transfers
 da0: 95396MB (195371568 512 byte sectors: 255H 63S/T 12161C)
 da0: quirks=3D0x2<NO_6_BYTE>
 ada1 at ahcich0 bus 0 scbus3 target 0 lun 0
 ada1: <ST500DM002-1BD142 KC44> ATA-8 SATA 3.x device
 ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
 ada1: Command Queueing enabled
 ada1: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C)
 ada1: quirks=3D0x1<4K>
 ada1: Previously was known as ad6
 SMP: AP CPU #1 Launched!
 Timecounter "TSC" frequency 1998041860 Hz quality 1000
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 Trying to mount root from ufs:/dev/ad4s1a [rw,noatime]...
 WARNING: /tmp was not properly dismounted
 WARNING: /usr was not properly dismounted
 WARNING: /usr: mount pending error: blocks 580 files 28
 WARNING: /var was not properly dismounted
 WARNING: /home was not properly dismounted
 tun0: link state changed to UP
 tun1: link state changed to UP
 WARNING: attempt to domain_add(netgraph) after domainfinalize()

 Fatal trap 12: page fault while in kernel mode
 cpuid =3D 1; apic id =3D 01
 fault virtual address	=3D 0x10
 fault code		=3D supervisor read, page not present
 instruction pointer	=3D 0x20:0xc05343be
 stack pointer	        =3D 0x28:0xf0767798
 frame pointer	        =3D 0x28:0xf0767798
 code segment		=3D base 0x0, limit 0xfffff, type 0x1b
 			=3D DPL 0, pres 1, def32 1, gran 1
 processor eflags	=3D interrupt enabled, resume, IOPL =3D 0
 current process		=3D 2315 (named)
 trap number		=3D 12
 panic: page fault
 cpuid =3D 1
 KDB: stack backtrace:
 #0 0xc0b27b58 at kdb_backtrace+0x4b
 #1 0xc0af0b19 at panic+0x16f
 #2 0xc0f8cb22 at trap_fatal+0x324
 #3 0xc0f8cc07 at trap_pfault+0xd9
 #4 0xc0f8df69 at trap+0x571
 #5 0xc0f77c4c at calltrap+0x6
 #6 0xc053f9ab at pf_test_rule+0x1be5
 #7 0xc054212a at pf_test+0x84d
 #8 0xc0547fa8 at pf_check_out+0x5c
 #9 0xc0bb8e64 at pfil_run_hooks+0x74
 #10 0xc0c1ca7a at ip_output+0x85d
 #11 0xc0c9ded3 at udp_send+0x93c
 #12 0xc0b5bb19 at sosend_dgram+0x467
 #13 0xc0b57137 at sosend+0x3f
 #14 0xc0b5e7a3 at kern_sendit+0x1ca
 #15 0xc0b5e9c1 at sendit+0xad
 #16 0xc0b5ea4f at sys_sendmsg+0x6b
 #17 0xc0f8d3dc at syscall+0x446
 Uptime: 7m38s
 Automatic reboot in 15 seconds - press a key on the console to abort
 Rebooting...
 cpu_reset: Restarting BSP
 cpu_reset_proxy: Stopped CPU 1
 Copyright (c) 1992-2013 The FreeBSD Project.
 Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 	The Regents of the University of California. All rights reserved.
 FreeBSD is a registered trademark of The FreeBSD Foundation.
 FreeBSD 9.2-PRERELEASE #26: Wed Sep 18 11:37:44 NZST 2013
     root at bmach.nederware.nl:/usr/obj/usr/src/sys/BMACH i386
 gcc version 4.2.1 20070831 patched [FreeBSD]
 link_elf: symbol ata_controlcmd undefined
 KLD file atapicam.ko - could not finalize loading
 CPU: Intel(R) Core(TM)2 CPU          4400  @ 2.00GHz (1998.04-MHz
 686-class CPU)
   Origin =3D "GenuineIntel"  Id =3D 0x6f2  Family =3D 0x6  Model =3D 0xf
 Stepping =3D 2

 Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PG=
 E,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
   Features2=3D0xe39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM>=

   AMD Features=3D0x20100000<NX,LM>
   AMD Features2=3D0x1<LAHF>
   TSC: P-state invariant, performance statistics
 real memory  =3D 4294967296 (4096 MB)
 avail memory =3D 3399114752 (3241 MB)
 Event timer "LAPIC" quality 400
 ACPI APIC Table: <INTEL  DP965LT >
 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 FreeBSD/SMP: 1 package(s) x 2 core(s)
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
 ioapic0: Changing APIC ID to 2
 ioapic0 <Version 2.0> irqs 0-23 on motherboard
 kbd1 at kbdmux0
 cryptosoft0: <software crypto> on motherboard
 acpi0: <INTEL DP965LT> on motherboard
 acpi0: Power Button (fixed)
 cpu0: <ACPI CPU> on acpi0
 cpu1: <ACPI CPU> on acpi0
 atrtc0: <AT realtime clock> port 0x70-0x71,0x74-0x77 irq 8 on acpi0
 Event timer "RTC" frequency 32768 Hz quality 0
 attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
 Timecounter "i8254" frequency 1193182 Hz quality 0
 Event timer "i8254" frequency 1193182 Hz quality 100
 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed03fff on acpi0
 Timecounter "HPET" frequency 14318180 Hz quality 950
 Event timer "HPET" frequency 14318180 Hz quality 450
 Event timer "HPET1" frequency 14318180 Hz quality 440
 Event timer "HPET2" frequency 14318180 Hz quality 440
 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
 acpi_button0: <Sleep Button> on acpi0
 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
 pci0: <ACPI PCI bus> on pcib0
 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
 pci1: <ACPI PCI bus> on pcib1
 vgapci0: <VGA-compatible display> port 0x4000-0x407f mem
 0xe2000000-0xe2ffffff,0xd0000000-0xdfffffff,0xe0000000-0xe1ffffff irq 16
 at device 0.0 on pci1
 pci0: <simple comms> at device 3.0 (no driver attached)
 em0: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x50e0-0x50ff mem
 0xe3500000-0xe351ffff,0xe3524000-0xe3524fff irq 20 at device 25.0 on pci0=

 em0: Using an MSI interrupt
 em0: Ethernet address: 00:19:d1:e8:c7:b3
 uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x50c0-0x50df irq
 16 at device 26.0 on pci0
 uhci0: LegSup =3D 0x2f00
 usbus0 on uhci0
 uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x50a0-0x50bf irq
 21 at device 26.1 on pci0
 uhci1: LegSup =3D 0x2f00
 usbus1 on uhci1
 ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem
 0xe3525c00-0xe3525fff irq 18 at device 26.7 on pci0
 usbus2: EHCI version 1.0
 usbus2 on ehci0
 hdac0: <Intel 82801H HDA Controller> mem 0xe3520000-0xe3523fff irq 22 at
 device 27.0 on pci0
 pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
 pci2: <ACPI PCI bus> on pcib2
 pcib3: <ACPI PCI-PCI bridge> at device 28.1 on pci0
 pci3: <ACPI PCI bus> on pcib3
 atapci0: <Marvell 88SE6101 UDMA133 controller> port
 0x3018-0x301f,0x3024-0x3027,0x3010-0x3017,0x3020-0x3023,0x3000-0x300f
 mem 0xe3400000-0xe34001ff irq 17 at device 0.0 on pci3
 ata2: <ATA channel> at channel 0 on atapci0
 pcib4: <ACPI PCI-PCI bridge> at device 28.2 on pci0
 pci4: <ACPI PCI bus> on pcib4
 pcib5: <ACPI PCI-PCI bridge> at device 28.3 on pci0
 pci5: <ACPI PCI bus> on pcib5
 pcib6: <ACPI PCI-PCI bridge> at device 28.4 on pci0
 pci6: <ACPI PCI bus> on pcib6
 uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x5080-0x509f irq
 23 at device 29.0 on pci0
 uhci2: LegSup =3D 0x2f00
 usbus3 on uhci2
 uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x5060-0x507f irq
 19 at device 29.1 on pci0
 uhci3: LegSup =3D 0x2f00
 usbus4 on uhci3
 uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x5040-0x505f irq
 18 at device 29.2 on pci0
 uhci4: LegSup =3D 0x2f00
 usbus5 on uhci4
 ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem
 0xe3525800-0xe3525bff irq 23 at device 29.7 on pci0
 usbus6: EHCI version 1.0
 usbus6 on ehci1
 pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
 pci7: <ACPI PCI bus> on pcib7
 em1: <Intel(R) PRO/1000 Legacy Network Connection 1.0.6> port
 0x2000-0x203f mem 0xe3320000-0xe333ffff,0xe3300000-0xe331ffff irq 21 at
 device 0.0 on pci7
 em1: Ethernet address: 00:1b:21:51:e1:e0
 pcib8: <PCI-PCI bridge> at device 1.0 on pci7
 pci8: <PCI bus> on pcib8
 ahc0: <Adaptec 3940 Ultra SCSI adapter> port 0x1400-0x14ff mem
 0xe3201000-0xe3201fff irq 22 at device 4.0 on pci8
 aic7880: Ultra Wide Channel A, SCSI Id=3D7, 16/253 SCBs
 ahc1: <Adaptec 3940 Ultra SCSI adapter> port 0x1000-0x10ff mem
 0xe3200000-0xe3200fff irq 21 at device 5.0 on pci8
 aic7880: Ultra Wide Channel B, SCSI Id=3D0, 16/253 SCBs
 fxp0: <Intel 82558 Pro/100 Ethernet> port 0x2040-0x205f mem
 0xe3000000-0xe3000fff,0xe3100000-0xe31fffff irq 18 at device 2.0 on pci7
 miibus0: <MII bus> on fxp0
 inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
 inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
 fxp0: Ethernet address: 00:90:27:17:93:5d
 pci7: <serial bus, FireWire> at device 3.0 (no driver attached)
 isab0: <PCI-ISA bridge> at device 31.0 on pci0
 isa0: <ISA bus> on isab0
 ahci0: <Intel ICH8 AHCI SATA controller> port
 0x5408-0x540f,0x5414-0x5417,0x5400-0x5407,0x5410-0x5413,0x5020-0x503f
 mem 0xe3525000-0xe35257ff irq 19 at device 31.2 on pci0
 ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier not supported
 ahcich0: <AHCI channel> at channel 0 on ahci0
 ahcich1: <AHCI channel> at channel 1 on ahci0
 ahcich4: <AHCI channel> at channel 4 on ahci0
 ahcich5: <AHCI channel> at channel 5 on ahci0
 pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
 ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
 ppc0: FIFO with 16/16/8 bytes threshold
 ppbus0: <Parallel port bus> on ppc0
 plip0: <PLIP network interface> on ppbus0
 lpt0: <Printer> on ppbus0
 lpt0: Interrupt-driven port
 ppi0: <Parallel I/O> on ppbus0
 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
 atkbd0: <AT Keyboard> irq 1 on atkbdc0
 kbd0 at atkbd0
 atkbd0: [GIANT-LOCKED]
 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
 ichwd0 on isa0
 pmtimer0 on isa0
 orm0: <ISA Option ROMs> at iomem 0xcf800-0xd07ff,0xd0800-0xd0fff pnpid
 ORM0000 on isa0
 sc0: <System console> at flags 0x100 on isa0
 sc0: VGA <16 virtual consoles, flags=3D0x300>
 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0=

 ata0: <ATA channel> at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
 ata1: <ATA channel> at port 0x170-0x177,0x376 irq 15 on isa0
 coretemp0: <CPU On-Die Thermal Sensors> on cpu0
 est0: <Enhanced SpeedStep Frequency Control> on cpu0
 p4tcc0: <CPU Frequency Thermal Control> on cpu0
 coretemp1: <CPU On-Die Thermal Sensors> on cpu1
 est1: <Enhanced SpeedStep Frequency Control> on cpu1
 p4tcc1: <CPU Frequency Thermal Control> on cpu1
 Timecounters tick every 1.000 msec
 vboxdrv: fAsync=3D0 offMin=3D0x1e0 offMax=3D0x438
 IPsec: Initialized Security Association Processing.
 ipfw2 (+ipv6) initialized, divert enabled, nat enabled, default to deny,
 logging disabled
 DUMMYNET 0 with IPv6 initialized (100409)
 load_dn_sched dn_sched FIFO loaded
 load_dn_sched dn_sched PRIO loaded
 load_dn_sched dn_sched QFQ loaded
 load_dn_sched dn_sched RR loaded
 load_dn_sched dn_sched WF2Q+ loaded
 hdacc0: <Sigmatel STAC9227X HDA CODEC> at cad 2 on hdac0
 hdaa0: <Sigmatel STAC9227X Audio Function Group> at nid 1 on hdacc0
 pcm0: <Sigmatel STAC9227X (Analog 5.1+HP/2.0)> at nid 13,15,14,10 and 11
 on hdaa0
 usbus0: 12Mbps Full Speed USB v1.0
 usbus1: 12Mbps Full Speed USB v1.0
 usbus2: 480Mbps High Speed USB v2.0
 usbus3: 12Mbps Full Speed USB v1.0
 usbus4: 12Mbps Full Speed USB v1.0
 usbus5: 12Mbps Full Speed USB v1.0
 usbus6: 480Mbps High Speed USB v2.0
 ugen0.1: <Intel> at usbus0
 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
 ugen1.1: <Intel> at usbus1
 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
 ugen2.1: <Intel> at usbus2
 uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
 ugen3.1: <Intel> at usbus3
 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
 ugen4.1: <Intel> at usbus4
 uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
 ugen5.1: <Intel> at usbus5
 uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
 ugen6.1: <Intel> at usbus6
 uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
 uhub0: 2 ports with 2 removable, self powered
 uhub1: 2 ports with 2 removable, self powered
 uhub3: 2 ports with 2 removable, self powered
 uhub4: 2 ports with 2 removable, self powered
 uhub5: 2 ports with 2 removable, self powered
 uhub2: 4 ports with 4 removable, self powered
 uhub6: 6 ports with 6 removable, self powered
 ugen2.2: <Hewlett-Packard> at usbus2
 ulpt0: <Printer> on usbus2
 ulpt0: using bi-directional mode
 ugen3.2: <vendor 0x0001> at usbus3
 uhid0: <vendor 0x0001 product 0x0000, class 0/0, rev 1.00/1.00, addr 2>
 on usbus3
 ugen2.3: <Sunplus Technology Inc.> at usbus2
 umass0: <Bulk Only Interface> on usbus2
 umass0:  SCSI over Bulk-Only; quirks =3D 0x4101
 umass0:9:0:-1: Attached to scbus9
 sa0 at ahc1 bus 0 scbus2 target 6 lun 0
 sa0: <SEAGATE DAT    9SP40-000 910B> Removable Sequential Access SCSI-3
 device
 sa0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
 ada0 at ata2 bus 0 scbus0 target 0 lun 0
 ada0: <ST3160815A 3.AAD> ATA-7 device
 ada0: 100.000MB/s transfers (UDMA5, PIO 8192bytes)
 ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
 ada0: Previously was known as ad4
 cd0 at ata2 bus 0 scbus0 target 1 lun 0
 cd0: <Optiarc DVD RW AD-7170A 1.85> Removable CD-ROM SCSI-0 device
 cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes)
 cd0: cd present [292819 x 2048 byte records]
 da0 at umass-sim0 bus 0 scbus9 target 0 lun 0
 da0: <Hitachi HTS721010G9SA00 > Fixed Direct Access SCSI-2 device
 da0: 40.000MB/s transfers
 da0: 95396MB (195371568 512 byte sectors: 255H 63S/T 12161C)
 da0: quirks=3D0x2<NO_6_BYTE>
 ada1 at ahcich0 bus 0 scbus3 target 0 lun 0
 ada1: <ST500DM002-1BD142 KC44> ATA-8 SATA 3.x device
 ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
 ada1: Command Queueing enabled
 ada1: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C)
 ada1: quirks=3D0x1<4K>
 ada1: Previously was known as ad6
 SMP: AP CPU #1 Launched!
 Timecounter "TSC" frequency 1998042600 Hz quality 1000
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 (cd0:ata2:0:1:0): READ(10). CDB: 28 00 00 04 77 d2 00 00 01 00
 (cd0:ata2:0:1:0): CAM status: SCSI Status Error
 (cd0:ata2:0:1:0): SCSI status: Check Condition
 (cd0:ata2:0:1:0): SCSI sense: ILLEGAL REQUEST asc:64,0 (Illegal mode for
 this track)
 (cd0:ata2:0:1:0): Info: 0x477d2
 (cd0:ata2:0:1:0): Error 6, Unretryable error
 (cd0:ata2:0:1:0): cddone: got error 0x6 back
 Trying to mount root from ufs:/dev/ad4s1a [rw,noatime]...
 WARNING: / was not properly dismounted
 WARNING: /tmp was not properly dismounted
 WARNING: /usr was not properly dismounted
 WARNING: /usr: mount pending error: blocks 0 files 4
 WARNING: /var was not properly dismounted
 WARNING: /var: mount pending error: blocks 4 files 1
 WARNING: /home was not properly dismounted

 --9qfsKgCMUbdjOVQRWvcgIrPbUjrRqdolN
 Content-Type: application/pgp-signature; name="signature.asc"
 Content-Description: OpenPGP digital signature
 Content-Disposition: attachment; filename="signature.asc"

 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/

 iQIcBAEBCAAGBQJSOXTYAAoJEKOfeD48G3g5H/4P/22oT7+FWNE6OxcP/ID44ain
 uYdPVupPq1fax2QZ7A09zpPE0yaU0ycjrPFSqE4g8ktc2PXtf8G/V27OpnhOmool
 yG7kVZ9cMOV8Q4jxVb305cJeuU5jJGFGeQMCnoExXLVPKHn/SjjOD0X20mUZu3Pk
 lE8Tm+J1uWfnx7z10fT9G55vQ+6SAE5tklh0wJh9WH1xCs1UABtPhk2wz9n2HJmf
 Kw+VWcfBDAso7b8R6tCGGmFb9JLCxBiv6xWZ/it65qz8SwrmQSLFgC7kHIP4ZJJ1
 TW5XQ9Mt3GW2eiKWLdUf1jezC6+MadYUHyw+cPZHaEJCdwXQckTz43wfRbXjYs9Y
 suUwwtvW9vIsgDnxGbWgfYX5vBR1OoP7bUYlK7qLMjEzny6XR4JWUW5EjhiDEjye
 SrEkRNQd3wxEHyeJdOkf3Q+s5CRe8C+nE5R/XY52GNeJFUm0j7vxr4zVGpvJ6I0g
 p2o2YWXMvDvubZJ0VciSvFw7wF+6FREygFOZw1hXMZJv2+hUCvzCebcceEZiAfMe
 CpKS+odFToCTVgOAfeFBMDJ51VTVq0NpTiRSe2aBbfSUP/K233QhR17cEw0oHzTe
 RZrrO3RHm4/ObhMdwEDZIMH4a0j+koBX+Krr9ElujPwxt6qxQD/Q2+YH+3RdM8Wh
 7Ou+HJtSsLtLkl/YAG6V
 =eNEY
 -----END PGP SIGNATURE-----

 --9qfsKgCMUbdjOVQRWvcgIrPbUjrRqdolN--