FreeBSD 7.0 isoonly CD boot fails

[Kai Lockwood]

Hello,

Trying to install 7.0 from a bootonly CD on to a Integrity rx2600 .
System crashes partway through the booting proces. Output below:

fs0:\> efi\boot\bootia64.efi
Consoles: EFI console
Image base: 0x00000040fef70000

FreeBSD/ia64 EFI boot, Revision 1.2
(root at pluto1.freebsd.org, Sun Feb 24 21:12:16 UTC 2008)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0xb46ac0+0x3f308 syms=[0x8+0x7a820+0x8+0x6b072]
/
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel] in 8 seconds...

Type '?' for a list of commands, 'help' for more detailed help.
OK set hw.ata.atapi_dma=0
OK set hw.ata.ata_dma=0
OK set hw.ata.wc=0
OK boot
Entering /boot/kernel/kernel at 0xe000000004070000...
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
      The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Mon Feb 25 07:27:59 UTC 2008
  root at pluto1.freebsd.org:/usr/obj/usr/src/sys/GENERIC
CPU: Madison (1300.00-Mhz Itanium 2)
 Origin = "GenuineIntel"  Revision = 5
 Features = 0x1<LB>
real memory  = 4273651712 (4075 MB)
avail memory = 4067926016 (3879 MB)
FPSWA Revision = 0x10012, Entry = 0xe0000040ffe60050
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0: SAPIC Id=0, SAPIC Eid=0 (BSP)
cpu1: SAPIC Id=1, SAPIC Eid=0
acpi0: <HP> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> iomem 0xff5c1004-0xff5c1007 on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
ohci0: <NEC uPD 9210 USB controller> mem 0x80023000-0x80023fff irq 16 at device0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0
usb0: <NEC uPD 9210 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <NEC uPD 9210 USB controller> mem 0x80022000-0x80022fff irq 17 at device0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0
usb1: <NEC uPD 9210 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ehci0: <NEC uPD 720100 USB 2.0 controller> mem 0x80021000-0x800210ff irq 18 at 0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 0.95
usb2: companion controllers, 3 ports each: usb0 usb1
usb2: <NEC uPD 720100 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 5 ports with 5 removable, self powered
atapci0: <SiI CMD 649 UDMA100 controller> port 0xd58-0xd5f,0xd64-0xd67,0xd50-0x0
atapci0: [ITHREAD]
atapci0: HW has secondary channel disabled
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
fxp0: <Intel 82550 Pro/100 Ethernet> port 0xd00-0xd3f mem 0x80020000-0x80020fff0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:30:6e:4c:cb:96
fxp0: [ITHREAD]
pcib1: <ACPI Host-PCI bridge> on acpi0
pci32: <ACPI PCI bus> on pcib1
mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x2100-0x21ff mem 0x90840000-0x9084ff2
mpt0: [ITHREAD]
mpt0: MPI Version=1.2.12.0
mpt1: <LSILogic 1030 Ultra4 Adapter> port 0x2000-0x20ff mem 0x90820000-0x9082ff2
mpt1: [ITHREAD]
mpt1: MPI Version=1.2.12.0
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x105> mem 0x92
miibus1: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-o
bge0: Ethernet address: 00:30:6e:4c:ca:15
bge0: [ITHREAD]
pcib2: <ACPI Host-PCI bridge> on acpi0
pci64: <ACPI PCI bus> on pcib2
pcib3: <ACPI Host-PCI bridge> on acpi0
pci96: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 1.0 on pci96
pci97: <ACPI PCI bus> on pcib4
ciss0: <HP Smart Array 6400> port 0x6000-0x60ff mem 0xb0080000-0xb0081fff,0xb007
ciss0: [ITHREAD]
pcib5: <ACPI Host-PCI bridge> on acpi0
pci128: <ACPI PCI bus> on pcib5
pcib6: <ACPI Host-PCI bridge> on acpi0
pci192: <ACPI PCI bus> on pcib6
pcib7: <ACPI Host-PCI bridge> on acpi0
pci224: <ACPI PCI bus> on pcib7
uart0: <16550 or compatible> mem 0xf4051000-0xf405100f irq 82 at device 1.0 on 4
uart0: [FILTER]
puc0: <HP Diva Serial [GSP] Multiport UART - Everest SP2> mem 0xf4050000-0xf4054
puc0: [FILTER]
uart1: <Non-standard ns8250 class UART with FIFOs> on puc0
uart1: [FILTER]
vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xf0000000-0xf3ffffff,4
uart2: <16550 or compatible> iomem 0xff5e0000-0xff5e0007 irq 34 on acpi0
uart2: [FILTER]
uart2: console (9600,n,8,1)
uart3: <16550 or compatible> iomem 0xff5e2000-0xff5e2007 irq 35 on acpi0
uart3: [FILTER]
uart3: debug port (9600,n,8,1)
Timecounters tick every 1.000 msec
Waiting 5 seconds for SCSI devices to settle
md0: Preloaded image </boot/mfsroot> 8388608 bytes at 0xe000000004c6b670
acd0: DVDROM <DV-28E-B/2.2B> at ata2-master PIO4
init died (signal 0, exit 1)
panic: Going nowhere without my init!
cpuid = 1
KDB: enter: panic
[thread pid 1 tid 100001 ]
Stopped at      kdb_enter+0x81: [F1]    nop.f 0x0
db> bt
Tracing pid 1 tid 100001 td 0xe000000010641b00
kdb_enter(0xe0000000049e6110, 0xe000000004536d20, 0x793, 0xa00000005df13398) at
kdb_enter+0x81
panic(0xe0000000049e2da0, 0x0, 0x1, 0xc000000000000205, 0x20000000004cc8f8) at p
anic+0x2e0
exit1(0xe000000010641b00, 0x100) at exit1+0x120
sys_exit(0xe000000010641b00, 0xa00000005df134e8, 0xe0000000049889b0, 0x48e, 0x0)
at sys_exit+0x30
syscall(0xa00000005df13400, 0xe000000010641b00, 0xe00000001063ba70, 0xe000000004
af52c8, 0x1, 0xa00000005df134e8, 0xe000000004984390, 0x8) at syscall+0x450
epc_syscall_return() at epc_syscall_return
db>