kern/112710: if_re driver detects incorrect b243a405a405 MAC
address on SMC9452TX-1 pci gigabit cards
Keve Nagy
wforms at safe-mail.net
Wed May 16 13:00:11 UTC 2007
>Number: 112710
>Category: kern
>Synopsis: if_re driver detects incorrect b243a405a405 MAC address on SMC9452TX-1 pci gigabit cards
>Confidential: no
>Severity: non-critical
>Priority: low
>Responsible: freebsd-bugs
>State: open
>Quarter:
>Keywords:
>Date-Required:
>Class: sw-bug
>Submitter-Id: current-users
>Arrival-Date: Wed May 16 13:00:10 GMT 2007
>Closed-Date:
>Last-Modified:
>Originator: Keve Nagy
>Release: FreeBSD/i386 6.2-RELEASE-p4
>Organization:
N/A
>Environment:
FreeBSD/i386 6.2-RELEASE-p4 on an IBM Netfinity 5000 (dual PIII/500) with 512MB RAM
>Description:
I just purchased 8 pieces of cheap gigabit ethernet cards to turn an old PIII into an internal router. All NICs are "SMC9452TX-1" type 32-bit PCI 10/100/1000 single RJ45 and carry a chip labelled "RTL8169SC 68102S1 G643 TAIWAN".
Serial number and MAC address printed on back of the PCB (sticker):
ENG70400759 0013f766b8f5
ENG70400758 0013f766b8f1
ENG70400744 0013f766b762
ENG70400708 0013f766b782
ENG70400752 0013f766b8ef
ENG70400751 0013f766b8f3
ENG70400707 0013f766b784
ENG70400753 0013f766b75d
From now on I refer to the top 5 of these as BAD cards while the bottom 3 will be referred to as GOOD cards. See later why! Under FreeBSD 6.2R all the cards are detected by the if_re driver as "re#: <RealTek 8169SB/8110SB Single-chip Gigabit Ethernet>".
Remember! The cards are exactly the same type, they were purchased together at the same shop at the same time, and I found no visible differences between them. Not on the PCB, not on labels, not in messages or version numbers spat out by firmware, driver, etc. Their product serial number also proves that they are from the same manufacturing series.
[Problem]
=========
For the 5 "bad" cards the if_re.ko driver detects an incorrect b2:43:a4:05:a4:05 MAC address while for the 3 "good" cards the expected and above listed correct MAC addresses are displayed. If multiple numbers of the "bad" cards are installed they all report to have the same "fake" b243a405a405 address. No matter in which order, which pci slot the cards are inserted. The 5 "bad" ones always appear to have the fake MAC address (always that same one fake MAC address, for each and all of the bad cards) while the 3 "good" ones always report the correct MAC address. Mixing the good cards with the bad cards cahnges nothing. The good ones are good, the bad ones are bad.
The cards have also been tested in another PC, a Pentium D dual core IBM ThinkCentre. Same results. The "bad" cards consistently report the fake MAC address while the "good" cards report the correct ones. (tested one card at a time, as this ThinkCentre had only one spare PCI slot) Besides reporting the fake MAC address the "bad" cards operated fine. I used one of the "bad" cards in my desktop PC for a 48 hour period without any trouble or error (no other "bad" cards were present on the network during this time, of course).
Having the if_re driver compiled into the kernel, having it loaded from loader.conf OR even from the command line with kldload makes absolutely no difference.
So far, it seems to be a classic manufacturing error with the burnt-in MAC address being messed up.
Here comes the surprise! Running a test on the same machine where the problems were detected, using the same cards but this time running a Debian based Linux disk (uhu-linux 2.0), all the cards behaved perfectly. Not one reported the fake MAC address I experienced under FreeBSD. Each and every single card reported its expected MAC address, regardless of their pci slot location, order, or grouping layout. The "bad" and "good" cards behaved equally well.
So the problem is most probably around how the if_re driver gets the MAC address of these cards under FreeBSD. For some reason, the method produces the correct result for 3 of my cards and returns the same incorrect result for other 5 of them. The results are consistent using the 6.2R boot CD, the 6.2R kernel installed by default and my custom kernel (under 6.2R, -p3 and -p4).
I include the dmesg output from my Netfinity 5000 equipped with the 5 "bad" gigabit cards. Both the FreeBSD 6.2 and the Linux output are included. Please see how re0 .. re4 reports to have the fake MAC address under FreeBSD, and how the exact same hardware configuration reports to have the correct MAC addresses under Linux! Same hardware setup, only the bootdisk was changed from FreeBSD to Linux.
I also include the "ifconfig" output from both FreeBSD and Linux. The incorrect and correct MAC addresses are clearly visible here as well.
FreeBSD dmesg on my Netfinity with the 5 "bad" cards inserted:
--------------------------------------------------------------
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p3 #1: Wed Apr 25 15:59:41 CEST 2007
root@:/usr/obj/usr/src/sys/Netfinity5k
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium III/Pentium III Xeon/Celeron (498.67-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 536854528 (511 MB)
avail memory = 519991296 (495 MB)
ACPI APIC Table: <IBM SERMOHIC>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 1
cpu1 (AP): APIC ID: 0
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <IBM SERMOHIC> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xfe88-0xfe8b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
re0: <RealTek 8169SB/8110SB Single-chip Gigabit Ethernet> port 0x2000-0x20ff mem 0xfebffc00-0xfebffcff irq 18 at device 1.0 on pci0
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re0: Ethernet address: b2:43:a4:05:a4:05
re0: [FAST]
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0x2200-0x22ff mem 0xfebfe000-0xfebfefff irq 16 at device 6.0 on pci0
ahc0: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0x2300-0x23ff mem 0xfebfd000-0xfebfdfff irq 16 at device 6.1 on pci0
ahc1: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel B, SCSI Id=7, 32/253 SCBs
pci0: <network, ethernet> at device 9.0 (no driver attached)
pci0: <display, VGA> at device 10.0 (no driver attached)
isab0: <PCI-ISA bridge> port 0xfe00-0xfe0f at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <GENERIC ATA controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 18 at device 15.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xff700000-0xff700fff irq 18 at device 15.2 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
re1: <RealTek 8169SB/8110SB Single-chip Gigabit Ethernet> port 0x4b00-0x4bff mem 0xc0fdfc00-0xc0fdfcff irq 19 at device 2.0 on pci1
miibus1: <MII bus> on re1
rgephy1: <RTL8169S/8110S media interface> on miibus1
rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re1: Ethernet address: b2:43:a4:05:a4:05
re1: [FAST]
re2: <RealTek 8169SB/8110SB Single-chip Gigabit Ethernet> port 0x4c00-0x4cff mem 0xc0fdf800-0xc0fdf8ff irq 19 at device 3.0 on pci1
miibus2: <MII bus> on re2
rgephy2: <RTL8169S/8110S media interface> on miibus2
rgephy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re2: Ethernet address: b2:43:a4:05:a4:05
re2: [FAST]
re3: <RealTek 8169SB/8110SB Single-chip Gigabit Ethernet> port 0x4d00-0x4dff mem 0xc0fdf400-0xc0fdf4ff irq 22 at device 4.0 on pci1
miibus3: <MII bus> on re3
rgephy3: <RTL8169S/8110S media interface> on miibus3
rgephy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re3: Ethernet address: b2:43:a4:05:a4:05
re3: [FAST]
re4: <RealTek 8169SB/8110SB Single-chip Gigabit Ethernet> port 0x4e00-0x4eff mem 0xc0fdf000-0xc0fdf0ff irq 22 at device 5.0 on pci1
miibus4: <MII bus> on re4
rgephy4: <RTL8169S/8110S media interface> on miibus4
rgephy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re4: Ethernet address: b2:43:a4:05:a4:05
re4: [FAST]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xccfff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <10 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
sa0 at ahc1 bus 0 target 6 lun 0
sa0: <Seagate STT20000N 7A64> Removable Sequential Access SCSI-2 device
sa0: 5.813MB/s transfers (5.813MHz, offset 15)
pass2 at ahc1 bus 0 target 14 lun 0
pass2: <SDR GEM200 2> Fixed Processor SCSI-2 device
pass2: 3.300MB/s transfers
SMP: AP CPU #1 Launched!
da0 at ahc1 bus 0 target 0 lun 0
da0: <IBM-PSG DNES-309170Y !# SC30> Fixed Direct Access SCSI-3 device
da0: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8678MB (17774160 512 byte sectors: 255H 63S/T 1106C)
Trying to mount root from ufs:/dev/da0s1a
Linux dmesg on my Netfinity with the 5 "bad" cards inserted:
------------------------------------------------------------
[17179569.184000] Linux version 2.6.17.6-10 (uhubuild at build) (gcc version 3.4.6) #1 SMP Mon Aug 21 11:06:08 CEST 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
[17179569.184000] BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000001fffc340 (usable)
[17179569.184000] BIOS-e820: 000000001fffc340 - 0000000020000000 (ACPI data)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 511MB LOWMEM available.
[17179569.184000] found SMP MP-table at 0009e1d0
[17179569.184000] On node 0 totalpages: 131068
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] Normal zone: 126972 pages, LIFO batch:31
[17179569.184000] DMI 2.1 present.
[17179569.184000] ACPI: RSDP (v000 IBM ) @ 0x000fdec0
[17179569.184000] ACPI: RSDT (v001 IBM SERMOHIC 0x00001001 IBM 0x00000000) @ 0x1fffff80
[17179569.184000] ACPI: FADT (v001 IBM SERMOHIC 0x00001001 IBM 0x00000000) @ 0x1fffff00
[17179569.184000] ACPI: MADT (v001 IBM SERMOHIC 0x00001001 IBM 0x00000000) @ 0x1ffffe80
[17179569.184000] ACPI: DSDT (v001 IBM SERMOHIC 0x00001000 MSFT 0x0100000b) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0xfe88
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
[17179569.184000] Processor #1 6:7 APIC version 17
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 6:7 APIC version 17
[17179569.184000] ACPI: IOAPIC (id[0x0e] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 14, version 17, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] ACPI: NMI_SRC (dfl dfl global_irq 20)
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/sda1 lang=hu
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[17179569.184000] Detected 498.808 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179571.564000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179571.568000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179571.640000] Memory: 510300k/524272k available (3154k kernel code, 13360k reserved, 1276k data, 292k init, 0k highmem)
[17179571.720000] Calibrating delay using timer specific routine.. 999.74 BogoMIPS (lpj=1999496)
[17179571.724000] kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved
[17179571.724000] Security Framework v1.0.0 initialized
[17179571.724000] Mount-cache hash table entries: 512
[17179571.724000] CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
[17179571.724000] CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
[17179571.724000] CPU: L1 I cache: 16K, L1 D cache: 16K
[17179571.724000] CPU: L2 cache: 512K
[17179571.724000] CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
[17179571.724000] Intel machine check architecture supported.
[17179571.724000] Intel machine check reporting enabled on CPU#0.
[17179571.724000] Checking 'hlt' instruction... OK.
[17179571.740000] SMP alternatives: switching to UP code
[17179571.740000] checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
[17179571.776000] Freeing initrd memory: 3444k freed
[17179571.788000] CPU0: Intel Pentium III (Katmai) stepping 03
[17179571.788000] SMP alternatives: switching to SMP code
[17179571.788000] Booting processor 1/0 eip 3000
[17179571.800000] Initializing CPU#1
[17179571.880000] Calibrating delay using timer specific routine.. 997.44 BogoMIPS (lpj=1994892)
[17179571.880000] CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
[17179571.880000] CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
[17179571.880000] CPU: L1 I cache: 16K, L1 D cache: 16K
[17179571.880000] CPU: L2 cache: 512K
[17179571.880000] CPU serial number disabled.
[17179571.880000] CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
[17179571.880000] Intel machine check architecture supported.
[17179571.880000] Intel machine check reporting enabled on CPU#1.
[17179571.880000] CPU1: Intel Pentium III (Katmai) stepping 03
[17179571.880000] Total of 2 processors activated (1997.19 BogoMIPS).
[17179571.880000] ENABLING IO-APIC IRQs
[17179571.880000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179572.024000] checking TSC synchronization across 2 CPUs: passed.
[17179572.028000] Brought up 2 CPUs
[17179572.208000] migration_cost=8000
[17179572.208000] Time: 15:27:26 Date: 03/27/107
[17179572.208000] NET: Registered protocol family 16
[17179572.208000] EISA bus registered
[17179572.208000] ACPI: bus type pci registered
[17179572.208000] PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
[17179572.208000] Setting up standard PCI resources
[17179572.216000] mtrr: your CPUs had inconsistent fixed MTRR settings
[17179572.216000] mtrr: probably your BIOS does not setup all CPUs.
[17179572.216000] mtrr: corrected configuration.
[17179572.216000] ACPI: Subsystem revision 20060127
[17179572.228000] ACPI: Interpreter enabled
[17179572.228000] ACPI: Using IOAPIC for interrupt routing
[17179572.228000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179572.228000] PCI: Probing PCI hardware (bus 00)
[17179572.236000] Boot video device is 0000:00:0a.0
[17179572.236000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1
[17179572.236000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179572.264000] ACPI: PCI Interrupt Link [LKSA] (IRQs 16) *15
[17179572.268000] ACPI: PCI Interrupt Link [LKSB] (IRQs 16) *10
[17179572.268000] ACPI: PCI Interrupt Link [LKVI] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[17179572.268000] ACPI: PCI Interrupt Link [LKNE] (IRQs 17) *11
[17179572.272000] ACPI: PCI Interrupt Link [LKUB] (IRQs 18) *10
[17179572.272000] ACPI: PCI Interrupt Link [LK1A] (IRQs 18) *11
[17179572.272000] ACPI: PCI Interrupt Link [LK1B] (IRQs 18) *0, disabled.
[17179572.276000] ACPI: PCI Interrupt Link [LK1C] (IRQs 18) *0, disabled.
[17179572.276000] ACPI: PCI Interrupt Link [LK1D] (IRQs 18) *0, disabled.
[17179572.276000] ACPI: PCI Root Bridge [PCI1] (0000:01)
[17179572.276000] PCI: Probing PCI hardware (bus 01)
[17179572.284000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
[17179572.300000] ACPI: PCI Interrupt Link [LK2A] (IRQs 19) *15
[17179572.304000] ACPI: PCI Interrupt Link [LK2B] (IRQs 19) *0, disabled.
[17179572.304000] ACPI: PCI Interrupt Link [LK2C] (IRQs 19) *0, disabled.
[17179572.304000] ACPI: PCI Interrupt Link [LK2D] (IRQs 19) *0, disabled.
[17179572.304000] ACPI: PCI Interrupt Link [LK3A] (IRQs 19) *9
[17179572.308000] ACPI: PCI Interrupt Link [LK3B] (IRQs 19) *0, disabled.
[17179572.308000] ACPI: PCI Interrupt Link [LK3C] (IRQs 19) *0, disabled.
[17179572.308000] ACPI: PCI Interrupt Link [LK3D] (IRQs 19) *0, disabled.
[17179572.312000] ACPI: PCI Interrupt Link [LK4A] (IRQs 22) *10
[17179572.312000] ACPI: PCI Interrupt Link [LK4B] (IRQs 22) *0, disabled.
[17179572.312000] ACPI: PCI Interrupt Link [LK4C] (IRQs 22) *0, disabled.
[17179572.316000] ACPI: PCI Interrupt Link [LK4D] (IRQs 22) *0, disabled.
[17179572.316000] ACPI: PCI Interrupt Link [LK5A] (IRQs 22) *11
[17179572.316000] ACPI: PCI Interrupt Link [LK5B] (IRQs 22) *0, disabled.
[17179572.320000] ACPI: PCI Interrupt Link [LK5C] (IRQs 22) *0, disabled.
[17179572.320000] ACPI: PCI Interrupt Link [LK5D] (IRQs 22) *0, disabled.
[17179572.320000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179572.320000] pnp: PnP ACPI init
[17179572.336000] pnp: PnP ACPI: found 17 devices
[17179572.336000] PnPBIOS: Disabled by ACPI PNP
[17179572.336000] PCI: Using ACPI for IRQ routing
[17179572.336000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[17179572.336000] TC classifier action (bugs to netdev at vger.kernel.org cc hadi at cyberus.ca)
[17179572.340000] pnp: 00:0c: ioport range 0xf50-0xf58 has been reserved
[17179572.340000] pnp: 00:0c: ioport range 0xfd00-0xfd3f has been reserved
[17179572.340000] pnp: 00:0c: ioport range 0xfe80-0xfebf could not be reserved
[17179572.340000] pnp: 00:0c: ioport range 0xfec0-0xfedf has been reserved
[17179572.340000] NET: Registered protocol family 2
[17179572.376000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[17179572.376000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[17179572.376000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[17179572.376000] TCP: Hash tables configured (established 16384 bind 8192)
[17179572.376000] TCP reno registered
[17179572.376000] Machine check exception polling timer started.
[17179572.376000] cpufreq: No nForce2 chipset.
[17179572.376000] IA-32 Microcode Update Driver: v1.14 <tigran at veritas.com>
[17179572.376000] IBM machine detected. Enabling interrupts during APM calls.
[17179572.376000] apm: BIOS not found.
[17179572.380000] Total HugeTLB memory allocated, 0
[17179572.380000] VFS: Disk quotas dquot_6.5.1
[17179572.380000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179572.380000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[17179572.380000] NTFS driver 2.1.27 [Flags: R/W].
[17179572.380000] EFS: 1.0a - http://aeschi.ch.eu.org/efs/
[17179572.380000] JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
[17179572.380000] JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2003 Red Hat, Inc.
[17179572.380000] QNX4 filesystem 0.2.3 registered.
[17179572.380000] JFS: nTxBlock = 4015, nTxLock = 32122
[17179572.388000] SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
[17179572.388000] SGI XFS Quota Management subsystem
[17179572.388000] BeFS version: 0.9.3
[17179572.388000] Initializing Cryptographic API
[17179572.388000] io scheduler noop registered
[17179572.388000] io scheduler anticipatory registered (default)
[17179572.388000] io scheduler deadline registered
[17179572.392000] io scheduler cfq registered
[17179572.392000] ACPI: Power Button (FF) [PWRF]
[17179572.392000] Using specific hotkey driver
[17179572.400000] ibm_acpi: ec object not found
[17179572.400000] isapnp: Scanning for PnP cards...
[17179572.756000] isapnp: No Plug & Play device found
[17179572.760000] Real Time Clock Driver v1.12ac
[17179572.760000] Non-volatile memory driver v1.2
[17179572.760000] Linux agpgart interface v0.101 (c) Dave Jones
[17179572.760000] agpgart: unable to determine aperture size.
[17179572.760000] agpgart: agp_backend_initialize() failed.
[17179572.760000] agpgart-serverworks: probe of 0000:00:00.0 failed with error -22
[17179572.760000] RAMDISK driver initialized: 8 RAM disks of 32768K size 1024 blocksize
[17179572.760000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179572.760000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179572.764000] Probing IDE interface ide0...
[17179573.004000] hda: CD-ROM CDU701-F, ATAPI CD/DVD-ROM drive
[17179573.100000] Probing IDE interface ide1...
[17179573.180000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179573.180000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[17179573.180000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179573.180000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179573.180000] mice: PS/2 mouse device common for all mice
[17179573.180000] input: PC Speaker as /class/input/input0
[17179573.228000] input: AT Translated Set 2 keyboard as /class/input/input1
[17179573.228000] wistron_btns: System unknown
[17179573.228000] device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel at redhat.com
[17179573.232000] EISA: Probing bus 0 at eisa.0
[17179573.232000] NET: Registered protocol family 1
[17179573.232000] Starting balanced_irq
[17179573.232000] Using IPI No-Shortcut mode
[17179573.232000] Suspend2 Core.
[17179573.232000] Suspend2 Compression Driver loading.
[17179573.232000] Suspend2 Encryption Driver loading.
[17179573.232000] Suspend2 Swap Writer loading.
[17179573.232000] Suspend2 FileWriter loading.
[17179573.232000] ACPI wakeup devices:
[17179573.232000]
[17179573.232000] ACPI: (supports S0 S4 S5)
[17179573.232000] Magic number: 3:533:488
[17179573.232000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[17179573.232000] RAMDISK: squashfs filesystem found at block 0
[17179573.232000] RAMDISK: Loading 3441KiB [1 disk] into ram disk... done.
[17179573.292000] VFS: Mounted root (squashfs filesystem) readonly.
[17179573.556000] SCSI subsystem initialized
[17179573.596000] ACPI: PCI Interrupt Link [LKSA] enabled at IRQ 16
[17179573.596000] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LKSA] -> GSI 16 (level, low) -> IRQ 177
[17179588.616000] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[17179588.616000] <Adaptec aic7895 Ultra SCSI adapter>
[17179588.616000] aic7895C: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs
[17179588.616000]
[17179592.556000] ACPI: PCI Interrupt Link [LKSB] enabled at IRQ 16
[17179592.556000] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [LKSB] -> GSI 16 (level, low) -> IRQ 177
[17179607.580000] scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[17179607.580000] <Adaptec aic7895 Ultra SCSI adapter>
[17179607.580000] aic7895C: Ultra Wide Channel B, SCSI Id=7, 32/253 SCBs
[17179607.580000]
[17179607.844000] Vendor: COMPAQ Model: DCHS04Y Rev: 5858
[17179607.844000] Type: Direct-Access ANSI SCSI revision: 02
[17179607.844000] scsi1:A:1:0: Tagged Queuing enabled. Depth 253
[17179607.844000] target1:0:1: Beginning Domain Validation
[17179607.848000] target1:0:1: wide asynchronous
[17179607.852000] target1:0:1: FAST-10 WIDE SCSI 11.6 MB/s ST (172 ns, offset 8)
[17179607.852000] target1:0:1: Domain Validation skipping write tests
[17179607.852000] target1:0:1: Ending Domain Validation
[17179608.908000] Vendor: Seagate Model: STT20000N Rev: 7A64
[17179608.908000] Type: Sequential-Access ANSI SCSI revision: 02
[17179608.908000] target1:0:6: Beginning Domain Validation
[17179608.920000] target1:0:6: FAST-10 SCSI 5.8 MB/s ST (172 ns, offset 15)
[17179608.928000] target1:0:6: Domain Validation skipping write tests
[17179608.928000] target1:0:6: Ending Domain Validation
[17179610.508000] Vendor: SDR Model: GEM200 Rev: 2
[17179610.508000] Type: Processor ANSI SCSI revision: 02
[17179610.508000] target1:0:14: Beginning Domain Validation
[17179610.508000] target1:0:14: Ending Domain Validation
[17179610.812000] piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device
[17179610.812000] piix4_smbus 0000:00:0f.0: Unusual config register value
[17179610.812000] piix4_smbus 0000:00:0f.0: Try using fix_hstcfg=1 if you experience problems
[17179610.812000] piix4_smbus 0000:00:0f.0: Host SMBus controller not enabled!
[17179610.868000] usbcore: registered new driver usbfs
[17179610.868000] usbcore: registered new driver hub
[17179610.876000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179610.880000] ACPI: PCI Interrupt Link [LKUB] enabled at IRQ 18
[17179610.880000] ACPI: PCI Interrupt 0000:00:0f.2[A] -> Link [LKUB] -> GSI 18 (level, low) -> IRQ 185
[17179610.880000] ohci_hcd 0000:00:0f.2: OHCI Host Controller
[17179610.880000] ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
[17179610.880000] ohci_hcd 0000:00:0f.2: irq 185, io mem 0xff700000
[17179610.936000] usb usb1: configuration #1 chosen from 1 choice
[17179610.936000] hub 1-0:1.0: USB hub found
[17179610.936000] hub 1-0:1.0: 2 ports detected
[17179611.068000] target1:0:1: FAST-10 WIDE SCSI 11.6 MB/s ST (172 ns, offset 8)
[17179611.144000] SCSI device sda: 8386000 512-byte hdwr sectors (4294 MB)
[17179611.208000] sda: Write Protect is off
[17179611.208000] sda: Mode Sense: c3 00 10 08
[17179611.212000] SCSI device sda: drive cache: write through w/ FUA
[17179611.276000] SCSI device sda: 8386000 512-byte hdwr sectors (4294 MB)
[17179611.340000] sda: Write Protect is off
[17179611.340000] sda: Mode Sense: c3 00 10 08
[17179611.344000] SCSI device sda: drive cache: write through w/ FUA
[17179611.344000] sda: sda1 sda2
[17179611.364000] sd 1:0:1:0: Attached scsi disk sda
[17179611.448000] libata version 1.20 loaded.
[17179611.716000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179611.716000] md: bitmap version 4.39
[17179611.740000] md: linear personality registered for level -1
[17179611.760000] md: multipath personality registered for level -4
[17179611.780000] md: raid0 personality registered for level 0
[17179611.808000] md: raid1 personality registered for level 1
[17179611.828000] raid5: automatically using best checksumming function: pIII_sse
[17179611.848000] pIII_sse : 992.000 MB/sec
[17179611.848000] raid5: using function: pIII_sse (992.000 MB/sec)
[17179611.856000] md: raid5 personality registered for level 5
[17179611.856000] md: raid4 personality registered for level 4
[17179611.956000] raid6: int32x1 118 MB/s
[17179612.024000] raid6: int32x2 106 MB/s
[17179612.092000] raid6: int32x4 107 MB/s
[17179612.160000] raid6: int32x8 116 MB/s
[17179612.228000] raid6: mmxx1 284 MB/s
[17179612.296000] raid6: mmxx2 347 MB/s
[17179612.364000] raid6: sse1x1 254 MB/s
[17179612.432000] raid6: sse1x2 308 MB/s
[17179612.432000] raid6: using algorithm sse1x2 (308 MB/s)
[17179612.432000] md: raid6 personality registered for level 6
[17179612.748000] Suspend2 2.2.6: You need to use a resume2= command line parameter to tell Suspend2 where to look for an image.
[17179612.748000] Suspend2 2.2.6: Resume2 parameter is empty. Suspending will be disabled.
[17179612.748000] Suspend2 2.2.6: Missing or invalid storage location (resume2= parameter). Please correct and rerun lilo (or equivalent) before suspending.
[17179612.804000] kjournald starting. Commit interval 5 seconds
[17179612.804000] EXT3-fs: mounted filesystem with ordered data mode.
[17179612.804000] VFS: Mounted root (ext3 filesystem) readonly.
[17179612.804000] Trying to move old root to /initrd ... /initrd does not exist. Ignored.
[17179612.808000] Unmounting old root
[17179612.812000] Trying to free ramdisk memory ... okay
[17179612.816000] Freeing unused kernel memory: 292k freed
[17179615.824000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179615.928000] st: Version 20050830, fixed bufsize 32768, s/g segs 256
[17179615.928000] st 1:0:6:0: Attached scsi tape st0
[17179615.928000] st0: try direct i/o: yes (alignment 512 B)
[17179616.004000] sd 1:0:1:0: Attached scsi generic sg0 type 0
[17179616.008000] st 1:0:6:0: Attached scsi generic sg1 type 1
[17179616.008000] 1:0:14:0: Attached scsi generic sg2 type 3
[17179616.084000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179616.100000] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[17179616.100000] ACPI: PCI Interrupt Link [LK1A] enabled at IRQ 18
[17179616.100000] ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LK1A] -> GSI 18 (level, low) -> IRQ 185
[17179616.100000] eth0: Identified chip type is 'RTL8169s/8110s'.
[17179616.100000] eth0: RTL8169 at 0xe0aeac00, 00:13:f7:66:b7:62, IRQ 185
[17179616.100000] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[17179616.104000] ACPI: PCI Interrupt Link [LK2A] enabled at IRQ 19
[17179616.104000] ACPI: PCI Interrupt 0000:01:02.0[A] -> Link [LK2A] -> GSI 19 (level, low) -> IRQ 193
[17179616.104000] eth1: Identified chip type is 'RTL8169s/8110s'.
[17179616.104000] eth1: RTL8169 at 0xe0b42c00, 00:13:f7:66:b7:82, IRQ 193
[17179616.104000] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[17179616.104000] ACPI: PCI Interrupt Link [LK3A] enabled at IRQ 19
[17179616.104000] ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LK3A] -> GSI 19 (level, low) -> IRQ 193
[17179616.104000] eth2: Identified chip type is 'RTL8169s/8110s'.
[17179616.104000] eth2: RTL8169 at 0xe0bbe800, 00:13:f7:66:b8:f1, IRQ 193
[17179616.104000] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[17179616.108000] ACPI: PCI Interrupt Link [LK4A] enabled at IRQ 22
[17179616.108000] ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LK4A] -> GSI 22 (level, low) -> IRQ 201
[17179616.108000] eth3: Identified chip type is 'RTL8169s/8110s'.
[17179616.108000] eth3: RTL8169 at 0xe0bde400, 00:13:f7:66:b8:ef, IRQ 201
[17179616.108000] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[17179616.108000] ACPI: PCI Interrupt Link [LK5A] enabled at IRQ 22
[17179616.108000] ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LK5A] -> GSI 22 (level, low) -> IRQ 201
[17179616.108000] eth4: Identified chip type is 'RTL8169s/8110s'.
[17179616.108000] eth4: RTL8169 at 0xe0be0000, 00:13:f7:66:b8:f5, IRQ 201
[17179616.208000] hda: ATAPI 32X CD-ROM drive, 128kB Cache
[17179616.208000] Uniform CD-ROM driver Revision: 3.20
[17179616.340000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179616.384000] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179616.384000] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179616.884000] lp: driver loaded but no devices found
[17179617.088000] ppdev: user-space parallel port driver
[17179617.120000] parport: PnPBIOS parport detected.
[17179617.120000] parport0: PC-style at 0x378, irq 7 [PCSPP]
[17179617.208000] lp0: using parport0 (interrupt-driven).
[17179617.208000] pcnet32.c:v1.32 18.Mar.2006 tsbogend at alpha.franken.de
[17179617.208000] ACPI: PCI Interrupt Link [LKNE] enabled at IRQ 17
[17179617.208000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LKNE] -> GSI 17 (level, low) -> IRQ 209
[17179617.208000] pcnet32: PCnet/FAST+ 79C972 at 0x2180, 00 06 29 50 d9 9e
[17179617.208000] tx_start_pt(0x0c00):~220 bytes, BCR18(9a61):BurstWrEn BurstRdEn NoUFlow
[17179617.208000] SRAMSIZE=0x1700, SRAM_BND=0x0800, assigned IRQ 209.
[17179617.208000] pcnet32: Found PHY 2000:5c10 at address 1.
[17179617.212000] eth5: registered as PCnet/FAST+ 79C972
[17179617.212000] pcnet32: 1 cards_found.
[17179618.080000] Floppy drive(s): fd0 is 1.44M
[17179618.096000] FDC 0 is a National Semiconductor PC87306
[17179618.164000] Capability LSM initialized
[17179618.212000] fuse init (API version 7.6)
[17179618.284000] loop: loaded (max 8 devices)
[17179618.404000] Adding 289160k swap on /dev/sda2. Priority:-1 extents:1 across:289160k
[17179618.648000] EXT3 FS on sda1, internal journal
[17179629.088000] r8169: eth0: link down
[17179629.248000] eth5: link up, 100Mbps, full-duplex
[17179629.332000] r8169: eth1: link down
[17179629.424000] r8169: eth2: link down
[17179629.508000] r8169: eth3: link down
[17179629.596000] r8169: eth4: link down
[17179631.612000] NET: Registered protocol family 17
[17179634.292000] NET: Registered protocol family 10
[17179634.292000] lo: Disabled Privacy Extensions
[17179634.292000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[17179634.292000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[17179634.292000] ADDRCONF(NETDEV_UP): eth2: link is not ready
[17179634.292000] ADDRCONF(NETDEV_UP): eth3: link is not ready
[17179634.292000] ADDRCONF(NETDEV_UP): eth4: link is not ready
[17179634.296000] IPv6 over IPv4 tunneling driver
[17179644.928000] eth5: no IPv6 routers present
FreeBSD ifconfig:
-----------------
re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
ether b2:43:a4:05:a4:05
media: Ethernet autoselect (100baseTX)
status: no carrier
re1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
ether b2:43:a4:05:a4:05
media: Ethernet autoselect (100baseTX)
status: no carrier
re2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
ether b2:43:a4:05:a4:05
media: Ethernet autoselect (100baseTX)
status: no carrier
re3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
ether b2:43:a4:05:a4:05
media: Ethernet autoselect (100baseTX)
status: no carrier
re4: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
ether b2:43:a4:05:a4:05
media: Ethernet autoselect (100baseTX)
status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
pflog0: flags=0<> mtu 33208
pcn0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:06:29:50:d9:9e
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
Linux ifconfig:
---------------
eth0 Link encap:Ethernet HWaddr 00:13:F7:66:B7:62
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:185 Base address:0xac00
eth1 Link encap:Ethernet HWaddr 00:13:F7:66:B7:82
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:193 Base address:0x2c00
eth2 Link encap:Ethernet HWaddr 00:13:F7:66:B8:F1
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:193 Base address:0xe800
eth3 Link encap:Ethernet HWaddr 00:13:F7:66:B8:EF
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:201 Base address:0xe400
eth4 Link encap:Ethernet HWaddr 00:13:F7:66:B8:F5
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:201
eth5 Link encap:Ethernet HWaddr 00:06:29:50:D9:9E
inet addr:192.0.2.236 Bcast:192.0.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:90 errors:0 dropped:0 overruns:0 frame:0
TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6249 (6.1 Kb) TX bytes:3672 (3.5 Kb)
Interrupt:209 Base address:0x2180
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:20 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2080 (2.0 Kb) TX bytes:2080 (2.0 Kb)
FreeBSD "pciconf -lv":
----------------------
hostb0 at pci0:0:0: class=0x060000 card=0x00000000 chip=0x00071166 rev=0x04 hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'NB6635 (CNB20-LE/HE) CPU to PCI Bridge'
class = bridge
subclass = HOST-PCI
hostb1 at pci0:0:1: class=0x060000 card=0x00000000 chip=0x00051166 rev=0x02 hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'NB6536 (CNB20-LE) PCI to PCI Bridge, bus/dev/func 0/0/1'
class = bridge
subclass = HOST-PCI
re0 at pci0:1:0: class=0x020000 card=0xee221113 chip=0x816910ec rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RTL8169 Gigabit Ethernet Adapter'
class = network
subclass = ethernet
ahc0 at pci0:6:0: class=0x010000 card=0x78959004 chip=0x78959004 rev=0x04 hdr=0x00
vendor = 'Adaptec Inc'
device = 'AIC-7895 Ultra-Wide SCSI Ctrlr on AHA-2940 AHA-394x'
class = mass storage
subclass = SCSI
ahc1 at pci0:6:1: class=0x010000 card=0x78959004 chip=0x78959004 rev=0x04 hdr=0x00
vendor = 'Adaptec Inc'
device = 'AIC-7895 Ultra-Wide SCSI Ctrlr on AHA-2940 AHA-394x'
class = mass storage
subclass = SCSI
pcn0 at pci0:9:0: class=0x020000 card=0x20001014 chip=0x20001022 rev=0x36 hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = 'Am79C970/1/2/3/5/6 PCnet LANCE PCI Ethernet Controller'
class = network
subclass = ethernet
none0 at pci0:10:0: class=0x030000 card=0x00dc1014 chip=0x89015333 rev=0x16 hdr=0x00
vendor = 'S3 Graphics Co., Ltd.'
device = 'S3 SonicVibes (86c617) Audio Accelerator PCI Trio 64V2 DX/GX'
class = display
subclass = VGA
isab0 at pci0:15:0: class=0x060100 card=0x02001166 chip=0x02001166 rev=0x4d hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'OSB4 PCI to ISA Bridge'
class = bridge
subclass = PCI-ISA
atapci0 at pci0:15:1: class=0x0101ea card=0x02101166 chip=0x02101166 rev=0x4a hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
class = mass storage
subclass = ATA
ohci0 at pci0:15:2: class=0x0c0310 card=0x02201166 chip=0x02201166 rev=0x04 hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'OSB4 OpenHCI Compliant USB Controller'
class = serial bus
subclass = USB
re1 at pci1:2:0: class=0x020000 card=0xee221113 chip=0x816910ec rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RTL8169 Gigabit Ethernet Adapter'
class = network
subclass = ethernet
re2 at pci1:3:0: class=0x020000 card=0xee221113 chip=0x816910ec rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RTL8169 Gigabit Ethernet Adapter'
class = network
subclass = ethernet
re3 at pci1:4:0: class=0x020000 card=0xee221113 chip=0x816910ec rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RTL8169 Gigabit Ethernet Adapter'
class = network
subclass = ethernet
re4 at pci1:5:0: class=0x020000 card=0xee221113 chip=0x816910ec rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RTL8169 Gigabit Ethernet Adapter'
class = network
subclass = ethernet
>How-To-Repeat:
Uncertain.
As I stated earlier, 3 of the cards work perfectly fine while 5 of them produces the MAC address problem. This way I cannot be sure that another card of the same series will show the defect or not.
Upon request, I might be able to provide some of the cards for further testing.
>Fix:
>Release-Note:
>Audit-Trail:
>Unformatted:
More information about the freebsd-bugs
mailing list