kern/91408 : [irq] ata(4) failure: SETFEATURES SET TRANSFER
MODE semaphore timeout !! DANGER Will Robinson !!
Eugene Grosbein
eugen at grosbein.pp.ru
Sun Apr 30 08:50:19 UTC 2006
The following reply was made to PR kern/91408; it has been noted by GNATS.
From: Eugene Grosbein <eugen at grosbein.pp.ru>
To: John Baldwin <jhb at freebsd.org>
Cc: bug-followup at freebsd.org, lightsquid at logvinov.com
Subject: Re: kern/91408 : [irq] ata(4) failure: SETFEATURES SET TRANSFER MODE semaphore timeout !! DANGER Will Robinson !!
Date: Sun, 30 Apr 2006 16:44:32 +0800
On Sat, Apr 29, 2006 at 10:54:09PM -0400, John Baldwin wrote:
> > With 6.1-RC of today I have the same sympthoms as with 5.4-RELEASE
> > (http://www.freebsd.org/cgi/query-pr.cgi?pr=kern/80815):
> >
> > 1) machine suffers from ATA timeouts if ACPI is fully enabled;
> > 2) debug.acpi.disable="pci_link" in /boot/loader.conf eliminates the
> > problem.
> >
> > So, Soren seems to be right: this is interrupt routing problem
> > and not ATA problem.
> >
> > The question is: should I consider the workaround mentioned above as
> > solution? What will I miss if I keep debug.acpi.disable="pci_link" forever?
>
> I think it's dangerous
What kind of trouble I am "asking for" while using debug.acpi.disable="pci_link"?
> and that you should just disable ACPI altogether if you wish to do that.
I think I do not wish that :-)
This machive has four OS now: FreeBSD 4.11-RELEASE (uses APM to turn power off),
Windows 98SE and Windows XP SP2 (use ACPI, no problems with it).
Would I be allowed to turn power off with 6.1 without ACPI enabled?
Would it be possible not only for 'shutdown -p', but for ACPI power button too?
> Can you provide verbose dmesg's for the
> case with pci_link disabled and the case where it is not disabled?
Here comes dmesg.acpi (ACPI is fully enabled):
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RC #13: Sun Apr 30 15:39:40 KRAST 2006
root at grosbein.pp.ru:/mnt/usr/local/obj6/usr/src/sys/DADV
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
WARNING: MPSAFE network stack disabled, expect reduced performance.
MEMGUARD DEBUGGING ALLOCATOR INITIALIZED:
MEMGUARD map base: 0xc36c9000
MEMGUARD map limit: 0xc495b000
MEMGUARD map size: 19472384 (Bytes)
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0925000.
Preloaded elf module "/boot/modules/acpi.ko" at 0xc092516c.
Calibrating clock(s) ... i8254 clock: 1193165 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 902050480 Hz
CPU: Intel Celeron (902.05-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 603914240 (575 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x0000000023597fff, 580333568 bytes (141683 pages)
avail memory = 581664768 (554 MB)
bios32: Found BIOS32 Service Directory header at 0xc00faef0
bios32: Entry = 0xfb370 (c00fb370) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb3a0
pnpbios: Found PnP BIOS data at 0xc00fbfc0
pnpbios: Entry = f0000:bfe8 Rev = 1.0
Other BIOS signatures found:
nfslock: pseudo-device
mem: <memory>
Pentium Pro MTRR support enabled
io: <I/O>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <AWARD AWRDACPI> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
Found $PIR table, 8 entries at 0xc00fdef0
PCI-Only Interrupts: 9 10 11
Location Bus Device Pin Link IRQs
slot 1 0 15 A 0x60 3 4 5 7 9 10 11 12 14 15
slot 1 0 15 B 0x61 3 4 5 7 9 10 11 12 14 15
slot 1 0 15 C 0x62 3 4 5 7 9 10 11 12 14 15
slot 1 0 15 D 0x63 3 4 5 7 9 10 11 12 14 15
slot 2 0 16 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 2 0 16 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 2 0 16 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 2 0 16 D 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 A 0x62 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 B 0x63 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 C 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 D 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 0 19 A 0x63 3 4 5 7 9 10 11 12 14 15
slot 4 0 19 B 0x60 3 4 5 7 9 10 11 12 14 15
slot 4 0 19 C 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 0 19 D 0x62 3 4 5 7 9 10 11 12 14 15
slot 5 0 20 A 0x60 3 4 5 7 9 10 11 12 14 15
slot 5 0 20 B 0x61 3 4 5 7 9 10 11 12 14 15
slot 5 0 20 C 0x62 3 4 5 7 9 10 11 12 14 15
slot 5 0 20 D 0x63 3 4 5 7 9 10 11 12 14 15
slot 6 0 14 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 6 0 14 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 6 0 14 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 6 0 14 D 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 7 A 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 7 B 0x61 3 4 5 7 9 10 11 12 14 15
embedded 0 7 C 0x62 3 4 5 7 9 10 11 12 14 15
embedded 0 7 D 0x63 3 4 5 7 9 10 11 12 14 15
embedded 0 1 A 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 1 B 0x61 3 4 5 7 9 10 11 12 14 15
embedded 0 1 C 0x62 3 4 5 7 9 10 11 12 14 15
embedded 0 1 D 0x63 3 4 5 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 10 11 12 14 15
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 10 11 12 14 15
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 3 4 5 6 7 10 11 12 14 15
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 3 4 5 6 7 10 11 12 14 15
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 10 11 12 14 15
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 10 11 12 14 15
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 3 4 5 6 7 10 11 12 14 15
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 3 4 5 6 7 10 11 12 14 15
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 12 14 15
ACPI timer: 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x4010
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x4041,0x5000-0x500f on acpi0
ACPI: Found matching pin for 0.16.INTA at func 0: 9
ACPI: Found matching pin for 0.18.INTA at func 0: 10
ACPI: Found matching pin for 0.19.INTA at func 0: 9
ACPI: Found matching pin for 0.19.INTB at func 1: 11
ACPI: Found matching pin for 0.19.INTC at func 2: 9
ACPI: Found matching pin for 0.7.INTD at func 2: 9
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base e8000000, size 26, enabled
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x88 (34000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000f000, size 4, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=9
map[20]: type 4, range 32, base 0000a000, size 5, enabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.PCI0.ISA_.LNKD:0)
pcib0: slot 7 INTD routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[90]: type 4, range 32, base 00005000, size 4, enabled
found-> vendor=0x8086, dev=0x1229, revid=0x02
bus=0, slot=16, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=9
map[10]: type 3, range 32, base f0104000, size 12, enabled
map[14]: type 4, range 32, base 0000a400, size 5, enabled
map[18]: type 1, range 32, base f0000000, size 20, enabled
pcib0: matched entry for 0.16.INTA (src \\_SB_.PCI0.ISA_.LNKB:0)
pcib0: slot 16 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB
found-> vendor=0x105a, dev=0x4d68, revid=0x02
bus=0, slot=18, func=0
class=01-80-85, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0430, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=10
powerspec 1 supports D0 D1 D3 current D0
map[10]: type 4, range 32, base 0000a800, size 3, enabled
map[14]: type 4, range 32, base 0000ac00, size 2, enabled
map[18]: type 4, range 32, base 0000b000, size 3, enabled
map[1c]: type 4, range 32, base 0000b400, size 2, enabled
map[20]: type 4, range 32, base 0000b800, size 4, enabled
map[24]: type 1, range 32, base f0100000, size 14, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.PCI0.ISA_.LNKC:0)
pcib0: slot 18 INTA routed to irq 10 via \\_SB_.PCI0.ISA_.LNKC
found-> vendor=0x1106, dev=0x3038, revid=0x61
bus=0, slot=19, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000bc00, size 5, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0)
pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD
found-> vendor=0x1106, dev=0x3038, revid=0x61
bus=0, slot=19, func=1
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000c000, size 5, enabled
pcib0: matched entry for 0.19.INTB (src \\_SB_.PCI0.ISA_.LNKA:0)
pcib0: slot 19 INTB routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA
found-> vendor=0x1106, dev=0x3104, revid=0x63
bus=0, slot=19, func=2
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base f0105000, size 8, enabled
pcib0: matched entry for 0.19.INTC (src \\_SB_.PCI0.ISA_.LNKB:0)
pcib0: slot 19 INTC routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB
found-> vendor=0x1106, dev=0x3044, revid=0x46
bus=0, slot=19, func=3
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x20 (8000 ns)
intpin=a, irq=9
powerspec 2 supports D0 D2 D3 current D0
map[10]: type 1, range 32, base f0106000, size 11, enabled
map[14]: type 4, range 32, base 0000c400, size 7, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0)
pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe8000000
agp0: allocating GATT for aperture of size 64M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x9000-0x9fff
pcib1: memory decode 0xec000000-0xedffffff
pcib1: prefetched decode 0xd8000000-0xe7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x5961, revid=0x01
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base d8000000, size 27, enabled
pcib1: (null) requested memory range 0xd8000000-0xdfffffff: good
map[14]: type 4, range 32, base 00009000, size 8, enabled
pcib1: (null) requested I/O range 0x9000-0x90ff: in range
map[18]: type 1, range 32, base ed000000, size 16, enabled
pcib1: (null) requested memory range 0xed000000-0xed00ffff: good
pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.ISA_.LNKA:0)
pcib0: slot 1 INTA routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA
pcib1: slot 0 INTA is routed to irq 11
found-> vendor=0x1002, dev=0x5941, revid=0x01
bus=1, slot=0, func=1
class=03-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base e0000000, size 27, enabled
pcib1: (null) requested memory range 0xe0000000-0xe7ffffff: good
map[14]: type 1, range 32, base ed010000, size 16, enabled
pcib1: (null) requested memory range 0xed010000-0xed01ffff: good
drm0: <ATI Radeon RV280 9200 SE> port 0x9000-0x90ff mem 0xd8000000-0xdfffffff,0xed000000-0xed00ffff irq 11 at device 0.0 on pci1
info: [drm] AGP at 0xe8000000 64MB
info: [drm] Initialized radeon 1.19.0 20050911
pci1: <display> at device 0.1 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=00 ostat1=00
ata0: stat0=0x00 err=0x00 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=00 stat1=00 devices=0x0
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x04 lsb=0x00 msb=0x02
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xa000-0xa01f irq 9 at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xa000
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
fxp0: <Intel 82557 Pro/100 Ethernet> port 0xa400-0xa41f mem 0xf0104000-0xf0104fff,0xf0000000-0xf00fffff irq 9 at device 16.0 on pci0
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf0104000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 8086 0001 0002
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:a0:c9:89:95:1f
fxp0: [GIANT-LOCKED]
atapci1: <Promise PDC20268 UDMA100 controller> port 0xa800-0xa807,0xac00-0xac03,0xb000-0xb007,0xb400-0xb403,0xb800-0xb80f mem 0xf0100000-0xf0103fff irq 10 at device 18.0 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xb800
atapci1: [MPSAFE]
ata2: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xa800
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xac00
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xb000
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xb400
ata3: reset tp1 mask=03 ostat0=50 ostat1=00
ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata3: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata3: [MPSAFE]
uhci1: <VIA 83C572 USB controller> port 0xbc00-0xbc1f irq 9 at device 19.0 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbc00
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 11 at device 19.1 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xc000
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xf0105000-0xf01050ff irq 9 at device 19.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xf0105000
ehci0: [GIANT-LOCKED]
ehci0: Dropped interrupts workaround enabled
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb1 usb2
usb3: <VIA VT6202 USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 4 ports with 4 removable, self powered
fwohci0: <VIA Fire II (VT6306)> port 0xc400-0xc47f mem 0xf0106000-0xf01067ff irq 9 at device 19.3 on pci0
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xf0106000
fwohci0: [GIANT-LOCKED]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:06:66:00:00:0d:c9
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:06:00:0d:c9
fwe0: bpf attached
fwe0: Ethernet address: 02:11:06:00:0d:c9
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x201 0x211 0x201 0x201
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: irq maps: 0x201 0x209 0x201 0x201
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0047
psm0: found NetMouse/NetScroll Optical
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model NetMouse/NetScroll Optical, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
YMH0021: start dependent (0)
YMH0021: adding io range 0x220-0x22f, size=0x10, align=0x10
YMH0021: adding io range 0x530-0x537, size=0x8, align=0x8
YMH0021: adding io range 0x388-0x38f, size=0x8, align=0x8
YMH0021: adding io range 0x330-0x331, size=0x2, align=0x2
YMH0021: adding io range 0x370-0x371, size=0x2, align=0x2
YMH0021: adding irq mask 0x20
YMH0021: adding dma mask 0x1
YMH0021: adding dma mask 0x2
YMH0021: start dependent (1)
YMH0021: adding io range 0x240-0x24f, size=0x10, align=0x10
YMH0021: adding io range 0xe80-0xe87, size=0x8, align=0x8
YMH0021: adding io range 0x388-0x38f, size=0x8, align=0x8
YMH0021: adding io range 0x300-0x301, size=0x2, align=0x2
YMH0021: adding io range 0x100-0xfff, size=0x2, align=0x2
YMH0021: adding irq mask 0xea0
YMH0021: adding dma mask 0xb
YMH0021: adding dma mask 0xb
YMH0021: start dependent (2)
YMH0021: adding io range 0x220-0x28f, size=0x10, align=0x10
YMH0021: adding io range 0x530-0xf4f, size=0x8, align=0x8
YMH0021: adding io range 0x388-0x3ff, size=0x8, align=0x8
YMH0021: adding io range 0x300-0x335, size=0x2, align=0x2
YMH0021: adding io range 0x100-0xfff, size=0x2, align=0x2
YMH0021: adding irq mask 0xea8
YMH0021: adding dma mask 0xb
YMH0021: adding dma mask 0xb
YMH0021: end dependent
YMH0022: start dependent (0)
YMH0022: adding io range 0x201-0x201, size=0x1, align=0x1
YMH0022: start dependent (2)
YMH0022: adding io range 0x201-0x211, size=0x1, align=0x10
YMH0022: end dependent
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd27ff on isa0
fb: new array size 4
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
pcm0: <Yamaha OPL-SAx> at port 0x220-0x22f,0x530-0x537,0x388-0x38f,0x330-0x331,0x370-0x371 irq 5 drq 0,1 on isa0
Yamaha: ver 0x21 DMA config 0x83
pcm0: [GIANT-LOCKED]
pcm0: sndbuf_setmap ff4000, 1000; 0xdbc11000 -> ff4000
pcm0: sndbuf_setmap ff3000, 1000; 0xdbc12000 -> ff3000
unknown: <OPL3-SA3 Sound Board> failed to probe at port 0x201 on isa0
uscanner0: Hewlett-Packard HP ScanJet 2200C, rev 1.10/1.00, addr 2
ugen0: American Power Conversion Back-UPS 500 FW: 6.5.I USB FW: c1, rev 1.10/1.00, addr 3
Device configuration finished.
linprocfs registered
procfs registered
Timecounter "TSC" frequency 902050480 Hz quality 800
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
IPsec: Initialized Security Association Processing.
DUMMYNET with IPv6 initialized (040826)
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding enabled, default to deny, logging disabled
lo0: bpf attached
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on PIIX4 chip
acd0: setting UDMA33 on PIIX4 chip
acd0: <NEC DVD RW ND-3500AG/2.18> DVDR drive at ata1 as master
acd0: read 8268KB/s (8268KB/s) write 8268KB/s (8268KB/s), 2048KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes: CDR, CDRW, DVDR, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-R 120mm data disc
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad4: setting PIO4 on PDC20268 chip
ad4: setting UDMA100 on PDC20268 chip
ad4: 76319MB <WDC WD800JB-00FMA0 13.03G13> at ata2-master UDMA100
ad4: 156301488 sectors [155061C/16H/63S] 16 sectors/interrupt 1 depth queue
ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad6: setting PIO4 on PDC20268 chip
ad6: setting UDMA100 on PDC20268 chip
ad6: 39266MB <IC35L040AVER07 0 ER4OA45A> at ata3-master UDMA100
ad6: 80418240 sectors [79780C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
GEOM: new disk ad6
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
(probe3:sbp0:0:3:0): error 22
(probe3:sbp0:0:3:0): Unretryable Error
(probe4:sbp0:0:4:0): error 22
(probe4:sbp0:0:4:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
Trying to mount root from ufs:/dev/ad6s2a
start_init: trying /sbin/init
gif0: bpf attached
tun0: bpf attached
ata2: reiniting channel ..
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly
ad4: setting PIO4 on PDC20268 chip
ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly
ad4: setting UDMA100 on PDC20268 chip
ad4: WARNING - SETFEATURES ENABLE RCACHE taskqueue timeout - completing request directly
ad4: WARNING - SETFEATURES ENABLE WCACHE taskqueue timeout - completing request directly
ad4: WARNING - SET_MULTI taskqueue timeout - completing request directly
ata2: reinit done ..
ad4: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=100861733
ata3: reiniting channel ..
ata3: reset tp1 mask=03 ostat0=50 ostat1=00
ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata3: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ad6: setting PIO4 on PDC20268 chip
ad6: setting UDMA100 on PDC20268 chip
ata3: reinit done ..
ad6: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=62118768
fxp0: promiscuous mode enabled
link_elf: symbol cd9660_wchar2char undefined
link_elf: symbol lminor undefined
psm: ENABLE_DEV return code:00fa
psm: SEND_AUX_DEV_STATUS return code:00fa
psm: status 20 02 64
psm: SET_SAMPLING_RATE (100) 00fa
psm: SET_RESOLUTION (3) 00fa
psm: SET_SCALING11 return code:00fa
psm: SEND_AUX_DEV_STATUS return code:00fa
psm: status 20 03 64
fxp0: promiscuous mode disabled
Now there is unified diff with dmesg.pcilink (pci_link is disabled):
--- dmesg.acpi Sun Apr 30 16:42:09 2006
+++ dmesg.pcilink Sun Apr 30 16:42:09 2006
@@ -11,10 +11,10 @@
MEMGUARD map size: 19472384 (Bytes)
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0925000.
Preloaded elf module "/boot/modules/acpi.ko" at 0xc092516c.
-Calibrating clock(s) ... i8254 clock: 1193165 Hz
+Calibrating clock(s) ... i8254 clock: 1193166 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
-Calibrating TSC clock ... TSC clock: 902050480 Hz
+Calibrating TSC clock ... TSC clock: 902050201 Hz
CPU: Intel Celeron (902.05-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
@@ -83,42 +83,6 @@
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
-pci_link0: Links after initial probe:
-Index IRQ Rtd Ref IRQs
- 0 11 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link0: Links after initial validation:
-Index IRQ Rtd Ref IRQs
- 0 11 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link0: Links after disable:
-Index IRQ Rtd Ref IRQs
- 0 255 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link1: Links after initial probe:
-Index IRQ Rtd Ref IRQs
- 0 9 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link1: Links after initial validation:
-Index IRQ Rtd Ref IRQs
- 0 9 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link1: Links after disable:
-Index IRQ Rtd Ref IRQs
- 0 255 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link2: Links after initial probe:
-Index IRQ Rtd Ref IRQs
- 0 10 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link2: Links after initial validation:
-Index IRQ Rtd Ref IRQs
- 0 10 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link2: Links after disable:
-Index IRQ Rtd Ref IRQs
- 0 255 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link3: Links after initial probe:
-Index IRQ Rtd Ref IRQs
- 0 9 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link3: Links after initial validation:
-Index IRQ Rtd Ref IRQs
- 0 9 N 0 3 4 5 6 7 10 11 12 14 15
-pci_link3: Links after disable:
-Index IRQ Rtd Ref IRQs
- 0 255 N 0 3 4 5 6 7 10 11 12 14 15
ACPI timer: 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
@@ -127,12 +91,30 @@
acpi_throttle0: P_CNT from P_BLK 0x4010
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x4041,0x5000-0x500f on acpi0
-ACPI: Found matching pin for 0.16.INTA at func 0: 9
-ACPI: Found matching pin for 0.18.INTA at func 0: 10
-ACPI: Found matching pin for 0.19.INTA at func 0: 9
-ACPI: Found matching pin for 0.19.INTB at func 1: 11
-ACPI: Found matching pin for 0.19.INTC at func 2: 9
-ACPI: Found matching pin for 0.7.INTD at func 2: 9
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC
+pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x7190, revid=0x03
@@ -165,7 +147,6 @@
intpin=d, irq=9
map[20]: type 4, range 32, base 0000a000, size 5, enabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.PCI0.ISA_.LNKD:0)
-pcib0: slot 7 INTD routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
@@ -182,7 +163,6 @@
map[14]: type 4, range 32, base 0000a400, size 5, enabled
map[18]: type 1, range 32, base f0000000, size 20, enabled
pcib0: matched entry for 0.16.INTA (src \\_SB_.PCI0.ISA_.LNKB:0)
-pcib0: slot 16 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB
found-> vendor=0x105a, dev=0x4d68, revid=0x02
bus=0, slot=18, func=0
class=01-80-85, hdrtype=0x00, mfdev=0
@@ -197,7 +177,6 @@
map[20]: type 4, range 32, base 0000b800, size 4, enabled
map[24]: type 1, range 32, base f0100000, size 14, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.PCI0.ISA_.LNKC:0)
-pcib0: slot 18 INTA routed to irq 10 via \\_SB_.PCI0.ISA_.LNKC
found-> vendor=0x1106, dev=0x3038, revid=0x61
bus=0, slot=19, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
@@ -207,7 +186,6 @@
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000bc00, size 5, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0)
-pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD
found-> vendor=0x1106, dev=0x3038, revid=0x61
bus=0, slot=19, func=1
class=0c-03-00, hdrtype=0x00, mfdev=1
@@ -217,7 +195,6 @@
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000c000, size 5, enabled
pcib0: matched entry for 0.19.INTB (src \\_SB_.PCI0.ISA_.LNKA:0)
-pcib0: slot 19 INTB routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA
found-> vendor=0x1106, dev=0x3104, revid=0x63
bus=0, slot=19, func=2
class=0c-03-20, hdrtype=0x00, mfdev=1
@@ -227,7 +204,6 @@
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base f0105000, size 8, enabled
pcib0: matched entry for 0.19.INTC (src \\_SB_.PCI0.ISA_.LNKB:0)
-pcib0: slot 19 INTC routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB
found-> vendor=0x1106, dev=0x3044, revid=0x46
bus=0, slot=19, func=3
class=0c-00-10, hdrtype=0x00, mfdev=0
@@ -238,7 +214,6 @@
map[10]: type 1, range 32, base f0106000, size 11, enabled
map[14]: type 4, range 32, base 0000c400, size 7, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0)
-pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe8000000
agp0: allocating GATT for aperture of size 64M
@@ -264,8 +239,6 @@
map[18]: type 1, range 32, base ed000000, size 16, enabled
pcib1: (null) requested memory range 0xed000000-0xed00ffff: good
pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.ISA_.LNKA:0)
-pcib0: slot 1 INTA routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA
-pcib1: slot 0 INTA is routed to irq 11
found-> vendor=0x1002, dev=0x5941, revid=0x01
bus=1, slot=0, func=1
class=03-80-00, hdrtype=0x00, mfdev=0
@@ -494,7 +467,7 @@
Device configuration finished.
linprocfs registered
procfs registered
-Timecounter "TSC" frequency 902050480 Hz quality 800
+Timecounter "TSC" frequency 902050201 Hz quality 800
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
IPsec: Initialized Security Association Processing.
@@ -523,47 +496,24 @@
ad6: 80418240 sectors [79780C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
GEOM: new disk ad6
-(probe0:sbp0:0:0:0): error 22
-(probe0:sbp0:0:0:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
-(probe3:sbp0:0:3:0): error 22
-(probe3:sbp0:0:3:0): Unretryable Error
-(probe4:sbp0:0:4:0): error 22
-(probe4:sbp0:0:4:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
+(probe0:sbp0:0:0:0): error 22
+(probe0:sbp0:0:0:0): Unretryable Error
+(probe3:sbp0:0:3:0): error 22
+(probe3:sbp0:0:3:0): Unretryable Error
+(probe4:sbp0:0:4:0): error 22
+(probe4:sbp0:0:4:0): Unretryable Error
Trying to mount root from ufs:/dev/ad6s2a
start_init: trying /sbin/init
gif0: bpf attached
tun0: bpf attached
-ata2: reiniting channel ..
-ata2: reset tp1 mask=03 ostat0=50 ostat1=00
-ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
-ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
-ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
-ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly
-ad4: setting PIO4 on PDC20268 chip
-ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly
-ad4: setting UDMA100 on PDC20268 chip
-ad4: WARNING - SETFEATURES ENABLE RCACHE taskqueue timeout - completing request directly
-ad4: WARNING - SETFEATURES ENABLE WCACHE taskqueue timeout - completing request directly
-ad4: WARNING - SET_MULTI taskqueue timeout - completing request directly
-ata2: reinit done ..
-ad4: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=100861733
-ata3: reiniting channel ..
-ata3: reset tp1 mask=03 ostat0=50 ostat1=00
-ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
-ata3: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
-ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
-ad6: setting PIO4 on PDC20268 chip
-ad6: setting UDMA100 on PDC20268 chip
-ata3: reinit done ..
-ad6: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=62118768
fxp0: promiscuous mode enabled
link_elf: symbol cd9660_wchar2char undefined
link_elf: symbol lminor undefined
Eugene Grosbein
More information about the freebsd-bugs
mailing list