kern/79262: [if_dc] Adaptec ANA-6922 not fully supported
Liudas B.
liudasb at centras.lt
Thu May 26 06:20:07 GMT 2005
The following reply was made to PR kern/79262; it has been noted by GNATS.
From: "Liudas B." <liudasb at centras.lt>
To: bug-followup at FreeBSD.org
Cc:
Subject: Re: kern/79262: [if_dc] Adaptec ANA-6922 not fully supported
Date: Thu, 26 May 2005 09:19:50 +0300
Same problems with FreeBSD 5.4
uname -a:
FreeBSD ausrine.b15.vu.lt 5.4-RELEASE FreeBSD 5.4-RELEASE #3: Wed May
25 23:02:11 EEST 2005 adm at ausrine.vu.lt:/usr/src/sys/i386/compile/
AUSRINE i386
dmesg output (kernel_options="-v"):
ioapic0: intpin 7 polarity: high
ioapic0: intpin 8 bus ISA
ioapic0: intpin 8 trigger: edge
ioapic0: intpin 8 polarity: high
ioapic0: intpin 9 bus ISA
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: high
ioapic0: intpin 10 bus ISA
ioapic0: intpin 10 trigger: level
ioapic0: intpin 10 polarity: high
ioapic0: intpin 11 bus ISA
ioapic0: intpin 11 trigger: level
ioapic0: intpin 11 polarity: high
ioapic0: intpin 12 bus ISA
ioapic0: intpin 12 trigger: edge
ioapic0: intpin 12 polarity: high
ioapic0: intpin 13 bus ISA
ioapic0: intpin 13 trigger: edge
ioapic0: intpin 13 polarity: high
ioapic0: intpin 14 bus ISA
ioapic0: intpin 14 trigger: edge
ioapic0: intpin 14 polarity: high
ioapic0: intpin 15 bus ISA
ioapic0: intpin 15 trigger: level
ioapic0: intpin 15 polarity: high
lapic: Routing ExtINT -> LINT0
lapic: LINT0 trigger: edge
lapic: LINT0 polarity: active-high
lapic: Routing NMI -> LINT1
lapic: LINT1 trigger: edge
lapic: LINT1 polarity: active-high
ioapic0 <Version 1.1> irqs 0-31 on motherboard
cpu0 BSP:
ID: 0x01000000 VER: 0x00040011 LDR: 0x02000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
null: <null device, zero device>
io: <I/O>
random: <entropy source, Software, Yarrow>
mem: <memory>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
cpu1 on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there
(id=71a08086)
pcibios: BIOS version 2.10
Found $PIR table, 15 entries at 0xc00fded0
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
slot 7 1 0 A 0x6a 3 4 5 6 7 9 10 11 12 14 15
slot 7 1 0 B 0x6b 3 4 5 6 7 9 10 11 12 14 15
embedded 0 7 D 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 4 A 0x69 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 12 A 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 12 B 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 12 C 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 12 D 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 13 A 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 13 B 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 13 C 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 13 D 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 14 A 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 14 B 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 14 C 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 14 D 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 4 2 8 A 0x64 3 4 5 6 7 9 10 11 12 14 15
slot 4 2 8 B 0x65 3 4 5 6 7 9 10 11 12 14 15
slot 4 2 8 C 0x66 3 4 5 6 7 9 10 11 12 14 15
slot 4 2 8 D 0x67 3 4 5 6 7 9 10 11 12 14 15
slot 5 2 9 A 0x65 3 4 5 6 7 9 10 11 12 14 15
slot 5 2 9 B 0x66 3 4 5 6 7 9 10 11 12 14 15
slot 5 2 9 C 0x67 3 4 5 6 7 9 10 11 12 14 15
slot 5 2 9 D 0x64 3 4 5 6 7 9 10 11 12 14 15
slot 6 2 10 A 0x66 3 4 5 6 7 9 10 11 12 14 15
slot 6 2 10 B 0x67 3 4 5 6 7 9 10 11 12 14 15
slot 6 2 10 C 0x64 3 4 5 6 7 9 10 11 12 14 15
slot 6 2 10 D 0x65 3 4 5 6 7 9 10 11 12 14 15
embedded 2 1 A 0x67 3 4 5 6 7 9 10 11 12 14 15
pcib0: <Intel 82443GX host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 15 Entries> on motherboard
$PIR: Links after initial probe:
Link IRQ Rtd Ref IRQs
0x6a 255 N 1 3 4 5 6 7 9 10 11 12 14 15
0x6b 255 N 1 3 4 5 6 7 9 10 11 12 14 15
0x63 255 N 4 3 4 5 6 7 9 10 11 12 14 15
0x69 255 N 1 3 4 5 6 7 9 10 11 12 14 15
0x60 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x61 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x62 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x64 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x65 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x66 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x67 255 N 4 3 4 5 6 7 9 10 11 12 14 15
$PIR: Found matching pin for 0.7.INTD at func 2: 11
$PIR: Found matching pin for 0.4.INTA at func 0: 9
$PIR: Found matching pin for 2.9.INTA at func 0: 7
$PIR: Found matching pin for 2.1.INTA at func 0: 10
$PIR: Links after initial IRQ discovery:
Link IRQ Rtd Ref IRQs
0x6a 255 N 1 3 4 5 6 7 9 10 11 12 14 15
0x6b 255 N 1 3 4 5 6 7 9 10 11 12 14 15
0x63 11 Y 4 3 4 5 6 7 9 10 11 12 14 15
0x69 9 Y 1 3 4 5 6 7 9 10 11 12 14 15
0x60 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x61 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x62 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x64 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x65 7 Y 3 3 4 5 6 7 9 10 11 12 14 15
0x66 255 N 3 3 4 5 6 7 9 10 11 12 14 15
0x67 10 Y 4 3 4 5 6 7 9 10 11 12 14 15
$PIR: IRQs used by BIOS: 7 9 10 11
$PIR: Interrupt Weights:
[ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
[ 0 0 0 0 0 0 0 3 0 1 4 4 0 0 0 0 ]
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f8000000, size 26, enabled
found-> vendor=0x8086, dev=0x71a0, revid=0x00
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0146, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x71a1, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x011f, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x48 (2160 ns), mingnt=0x85 (33250 ns), maxlat=0x00 (0
ns)
map[10]: type 1, range 32, base fec00000, size 10, enabled
found-> vendor=0x110a, dev=0x0015, revid=0x02
bus=0, slot=2, func=0
class=08-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0142, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1011, dev=0x0024, revid=0x03
bus=0, slot=3, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x60 (2880 ns), mingnt=0x0f (3750 ns), maxlat=0x03 (750
ns)
map[10]: type 1, range 32, base f4100000, size 12, enabled
map[14]: type 4, range 32, base 00001000, size 3, enabled
map[18]: type 1, range 32, base f4000000, size 20, enabled
$PIR: 0:4 INTA routed to irq 9
found-> vendor=0x110a, dev=0x001d, revid=0x01
bus=0, slot=4, func=0
class=ff-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0147, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00001800, size 4, port disabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0004, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00001400, size 5, enabled
$PIR: 0:7 INTD routed to irq 11
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
map[90]: type 4, range 32, base 0000f0b0, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xfff00000-0xfffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
pci0: <base peripheral> at device 2.0 (no driver attached)
pcib2: <PCIBIOS PCI-PCI bridge> at device 3.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 3
pcib2: I/O decode 0x2000-0x3fff
pcib2: memory decode 0xf4200000-0xf44fffff
pcib2: prefetched decode 0xf4500000-0xf7ffffff
pci2: <PCI bus> on pcib2
pci2: physical bus=2
map[10]: type 3, range 32, base f6000000, size 25, enabled
pcib2: device (null) requested decoded memory range 0xf6000000-
0xf7ffffff
map[14]: type 1, range 32, base f4300000, size 12, enabled
pcib2: device (null) requested decoded memory range 0xf4300000-
0xf4300fff
found-> vendor=0x1013, dev=0x00b8, revid=0x45
bus=2, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 00002000, size 8, enabled
pcib2: device (null) requested decoded I/O range 0x2000-0x20ff
map[14]: type 1, range 32, base f4302000, size 8, enabled
pcib2: device (null) requested decoded memory range 0xf4302000-
0xf43020ff
map[18]: type 1, range 32, base f4301000, size 12, enabled
pcib2: device (null) requested decoded memory range 0xf4301000-
0xf4301fff
$PIR: 2:1 INTA routed to irq 10
found-> vendor=0x1000, dev=0x000c, revid=0x01
bus=2, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0xf7 (7410 ns), mingnt=0x1e (7500 ns), maxlat=0x40
(16000 ns)
intpin=a, irq=10
map[10]: type 3, range 32, base f4500000, size 12, enabled
pcib2: device (null) requested decoded memory range 0xf4500000-
0xf4500fff
map[14]: type 4, range 32, base 00002400, size 5, enabled
pcib2: device (null) requested decoded I/O range 0x2400-0x241f
map[18]: type 1, range 32, base f4200000, size 20, enabled
pcib2: device (null) requested decoded memory range 0xf4200000-
0xf42fffff
$PIR: 2:9 INTA routed to irq 7
found-> vendor=0x8086, dev=0x1229, revid=0x05
bus=2, slot=9, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x38
(14000 ns)
intpin=a, irq=7
powerspec 1 supports D0 D1 D2 D3 current D0
found-> vendor=0x1011, dev=0x0024, revid=0x03
bus=2, slot=10, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0
ns)
pci2: <display, VGA> at device 0.0 (no driver attached)
sym0: <895> port 0x2000-0x20ff mem 0xf4301000-0xf4301fff,0xf4302000-
0xf43020ff irq 10 at device 1.0 on pci2
sym0: Reserved 0x100 bytes for rid 0x14 type 3 at 0xf4302000
sym0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xf4301000
sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/a0/01/00/24
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/80/01/08/24
sym0: SCAN FOR LUNS disabled for targets 0 1 2.
sym0: Delay (GEN=11): 233 msec, 38147 KHz
sym0: Delay (GEN=11): 266 msec, 33414 KHz
sym0: Delay (GEN=11): 265 msec, 33540 KHz
sym0: [GIANT-LOCKED]
sym0: enabling clock multiplier
sym0: Downloading SCSI SCRIPTS.
fxp0: <Intel 82558 Pro/100 Ethernet> port 0x2400-0x241f mem
0xf4200000-0xf42fffff,0xf4500000-0xf4500fff irq 7 at device 9.0 on
pci2
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf4500000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 0e11 b0d7 0005
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:50:8b:01:ad:97
fxp0: [MPSAFE]
pcib3: <PCI-PCI bridge> at device 10.0 on pci2
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0x3000-0x3fff
pcib3: memory decode 0xf4400000-0xf44fffff
pcib3: prefetched decode 0xfff00000-0xfffff
pci3: <PCI bus> on pcib3
pci3: physical bus=3
map[10]: type 4, range 32, base 00003000, size 7, enabled
pcib3: device (null) requested decoded I/O range 0x3000-0x307f
pcib2: device (null) requested decoded I/O range 0x3000-0x307f
map[14]: type 1, range 32, base f4400000, size 10, enabled
pcib3: device (null) requested decoded memory range 0xf4400000-
0xf44003ff
pcib2: device (null) requested decoded memory range 0xf4400000-
0xf44003ff
$PIR: Found IRQ 9 for link 0x66 from 7 9 10 11
ioapic0: Changing polarity for pin 9 to low
$PIR: 2:10 INTA routed to irq 9
pcib3: slot 4 INTA is routed to irq 9
found-> vendor=0x1011, dev=0x0019, revid=0x41
bus=3, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0xa5 (4950 ns), mingnt=0x14 (5000 ns), maxlat=0x28
(10000 ns)
intpin=a, irq=9
map[10]: type 4, range 32, base 00003400, size 7, enabled
pcib3: device (null) requested decoded I/O range 0x3400-0x347f
pcib2: device (null) requested decoded I/O range 0x3400-0x347f
map[14]: type 1, range 32, base f4400400, size 10, enabled
pcib3: device (null) requested decoded memory range 0xf4400400-
0xf44007ff
pcib2: device (null) requested decoded memory range 0xf4400400-
0xf44007ff
$PIR: 2:10 INTA routed to irq 9
pcib3: slot 8 INTA is routed to irq 9
found-> vendor=0x1011, dev=0x0019, revid=0x41
bus=3, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0xa5 (4950 ns), mingnt=0x14 (5000 ns), maxlat=0x28
(10000 ns)
intpin=a, irq=9
dc0: <Intel 21143 10/100BaseTX> port 0x3000-0x307f mem 0xf4400000-
0xf44003ff irq 9 at device 4.0 on pci3
dc0: Reserved 0x80 bytes for rid 0x10 type 4 at 0x3000
miibus1: <MII bus> on dc0
nsphy0: <DP83840 10/100 media interface> on miibus1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: bpf attached
dc0: Ethernet address: 00:00:d1:1d:d7:47
dc0: if_start running deferred for Giant
dc0: [GIANT-LOCKED]
dc1: <Intel 21143 10/100BaseTX> port 0x3400-0x347f mem 0xf4400400-
0xf44007ff irq 9 at device 8.0 on pci3
dc1: Reserved 0x80 bytes for rid 0x10 type 4 at 0x3400
miibus2: <MII bus> on dc1
dcphy0: <Intel 21143 NWAY media interface> on miibus2
dcphy0: 10baseT, 10baseT-FDX, auto
dc1: bpf attached
dc1: Ethernet address: ff:ff:ff:ff:ff:ff
dc1: if_start running deferred for Giant
dc1: [GIANT-LOCKED]
pci0: <unknown> at device 4.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <mass storage, ATA> at device 7.1 (no driver attached)
pci0: <serial bus, USB> at device 7.2 (no driver attached)
piix0: <PIIX Timecounter> port 0xf0b0-0xf0bf at device 7.3 on pci0
Timecounter "PIIX" frequency 3579545 Hz quality 0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
pnpbios: 17 devices, largest 170 bytes
PNP0c02: adding fixed memory32 range 0xfee00000-0xfee00fff,
size=0x1000
pnpbios: handle 0 device ID PNP0c02 (020cd041)
PNP0c02: adding io range 0x80-0x80, size=0x1, align=0x1
PNP0c02: adding io range 0xea-0xeb, size=0x2, align=0x1
PNP0c02: adding fixed memory32 range 0xfffe0000-0xffffffff,
size=0x20000
pnpbios: handle 1 device ID PNP0c02 (020cd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
PNP0c01: adding fixed memory32 range 0x100000-0x17ffffff,
size=0x17f00000
pnpbios: handle 2 device ID PNP0c01 (010cd041)
PNP0200: adding io range 0-0xf, size=0x10, align=0x1
PNP0200: adding io range 0x81-0x8f, size=0xf, align=0x1
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
pnpbios: handle 3 device ID PNP0200 (0002d041)
PNP0100: adding io range 0x40-0x43, size=0x4, align=0x1
PNP0100: adding irq mask 0x1
pnpbios: handle 5 device ID PNP0100 (0001d041)
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0x1
PNP0b00: adding irq mask 0x100
pnpbios: handle 6 device ID PNP0b00 (000bd041)
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
PNP0303: adding irq mask 0x2
pnpbios: handle 7 device ID PNP0303 (0303d041)
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
PNP0c04: adding irq mask 0x2000
pnpbios: handle 8 device ID PNP0c04 (040cd041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 9 device ID PNP0800 (0008d041)
pnpbios: handle 10 device ID PNP0c02 (020cd041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0x1
pnpbios: handle 11 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
PNP0c02: adding io range 0xf0c0-0xf0ff, size=0x40, align=0x1
PNP0c02: adding io range 0xf0b0-0xf0bf, size=0x10, align=0x1
PNP0c02: adding io range 0x10-0x18, size=0x9, align=0x1
PNP0c02: adding io range 0x1f-0x1f, size=0x1, align=0x1
PNP0c02: adding io range 0x24-0x25, size=0x2, align=0x1
PNP0c02: adding io range 0x28-0x29, size=0x2, align=0x1
PNP0c02: adding io range 0x2c-0x2d, size=0x2, align=0x1
PNP0c02: adding io range 0x30-0x31, size=0x2, align=0x1
PNP0c02: adding io range 0x34-0x35, size=0x2, align=0x1
PNP0c02: adding io range 0x38-0x39, size=0x2, align=0x1
PNP0c02: adding io range 0x3c-0x3d, size=0x2, align=0x1
PNP0c02: adding io range 0x50-0x52, size=0x3, align=0x1
PNP0c02: adding io range 0x72-0x77, size=0x6, align=0x1
PNP0c02: adding io range 0x90-0x9f, size=0x10, align=0x1
PNP0c02: adding io range 0xa4-0xa5, size=0x2, align=0x1
PNP0c02: adding io range 0xa8-0xa9, size=0x2, align=0x1
PNP0c02: adding io range 0xac-0xad, size=0x2, align=0x1
PNP0c02: adding io range 0xb0-0xbd, size=0xe, align=0x1
pnpbios: handle 12 device ID PNP0c02 (020cd041)
pnpbios: handle 14 device ID PNP0c02 (020cd041)
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x8
PNP0501: adding irq mask 0x10
pnpbios: handle 16 device ID PNP0501 (0105d041)
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0x8
PNP0501: adding irq mask 0x8
pnpbios: handle 17 device ID PNP0501 (0105d041)
PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0x8
PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0x1
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
pnpbios: handle 18 device ID PNP0700 (0007d041)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xcb800-0xcbfff,0xc8000-0xcb7ff,
0xc0000-0xc7fff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
ata0 failed to probe at port 0x1f0 irq 14 on isa0
ata1 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ic_type 90 part_id 80
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on
isa0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0xa001 0xa011 0xa001 0xa001
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0xa001 0xa009 0xa001 0xa001
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 05 50 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0c02> at port 0x4d0-0x4d1 on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 396820206 Hz quality -100
Timecounters tick every 10.000 msec
IP Filter: v3.4.35 initialized. Default = pass all, Logging = enabled
lo0: bpf attached
Waiting 2 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
sym0: enabling clock multiplier
sym0: Downloading SCSI SCRIPTS.
Interrupt storm detected on "irq9: dc0 dc1"; throttling interrupt
source
(probe0:sym0:0:0:0): Retrying Command
(probe1:sym0:0:1:0): Retrying Command
(probe2:sym0:0:2:0): Retrying Command
(probe5:sym0:0:5:0): error 22
(probe5:sym0:0:5:0): Unretryable Error
(probe7:sym0:0:8:0): phase change 6-7 6 at 0020df8c resid=4.
(probe1:sym0:0:1:1): error 22
(probe1:sym0:0:1:1): Unretryable Error
(probe1:sym0:0:1:2): error 22
(probe1:sym0:0:1:2): Unretryable Error
(probe1:sym0:0:1:3): error 22
(probe1:sym0:0:1:3): Unretryable Error
(probe1:sym0:0:1:4): error 22
(probe1:sym0:0:1:4): Unretryable Error
(probe1:sym0:0:1:5): error 22
(probe1:sym0:0:1:5): Unretryable Error
(probe1:sym0:0:1:6): error 22
(probe1:sym0:0:1:6): Unretryable Error
(probe1:sym0:0:1:7): error 22
(probe1:sym0:0:1:7): Unretryable Error
(probe0:sym0:0:0:1): error 22
(probe0:sym0:0:0:1): Unretryable Error
(probe0:sym0:0:0:2): error 22
(probe0:sym0:0:0:2): Unretryable Error
(probe0:sym0:0:0:3): error 22
(probe0:sym0:0:0:3): Unretryable Error
(probe0:sym0:0:0:4): error 22
(probe0:sym0:0:0:4): Unretryable Error
(probe0:sym0:0:0:5): error 22
(probe0:sym0:0:0:5): Unretryable Error
(probe0:sym0:0:0:6): error 22
(probe0:sym0:0:0:6): Unretryable Error
(probe0:sym0:0:0:7): error 22
(probe0:sym0:0:0:7): Unretryable Error
(probe0:sym0:0:2:1): error 22
(probe0:sym0:0:2:1): Unretryable Error
(probe0:sym0:0:2:2): error 22
(probe0:sym0:0:2:2): Unretryable Error
(probe0:sym0:0:2:3): error 22
(probe0:sym0:0:2:3): Unretryable Error
(probe0:sym0:0:2:4): error 22
(probe0:sym0:0:2:4): Unretryable Error
(probe0:sym0:0:2:5): error 22
(probe0:sym0:0:2:5): Unretryable Error
(probe0:sym0:0:2:6): error 22
(probe0:sym0:0:2:6): Unretryable Error
(probe0:sym0:0:2:7): error 22
(probe0:sym0:0:2:7): Unretryable Error
ses0 at sym0 bus 0 target 8 lun 0
ses0: <SIEMENS STM/L S1 4.1b> Fixed Processor SCSI-2 device
ses0: Serial Number 1
ses0: 3.300MB/s transfers
ses0: SAF-TE Compliant Device
pass0 at sym0 bus 0 target 0 lun 0
pass0: <HP 18.2GB A 80-B005 B005> Fixed Direct Access SCSI-2 device
pass0: Serial Number 3AK0A5ZJ000010071Z8W
pass0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged
Queueing Enabled
pass1 at sym0 bus 0 target 1 lun 0
pass1: <FUJITSU MAG3091LC 5210> Fixed Direct Access SCSI-2 device
pass1: Serial Number 00002277
pass1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged
Queueing Enabled
pass2 at sym0 bus 0 target 2 lun 0
pass2: <FUJITSU MAG3091LC 5210> Fixed Direct Access SCSI-2 device
pass2: Serial Number 00001305
pass2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged
Queueing Enabled
pass3 at sym0 bus 0 target 5 lun 0
pass3: <NEC CD-ROM DRIVE:465 1.13> Removable CD-ROM SCSI-2 device
pass3: 20.000MB/s transfers (20.000MHz, offset 16)
pass4 at sym0 bus 0 target 8 lun 0
pass4: <SIEMENS STM/L S1 4.1b> Fixed Processor SCSI-2 device
pass4: Serial Number 1
pass4: 3.300MB/s transfers
GEOM: new disk cd0
GEOM: new disk da0
GEOM: new disk da1
GEOM: new disk da2
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x00000000 VER: 0x00040011 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 2 (ISA IRQ 0) to cluster 0
ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0
ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
ioapic0: routing intpin 10 (ISA IRQ 10) to cluster 0
ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
(cd0:sym0:0:5:0): Retrying Command
da2 at sym0 bus 0 target 2 lun 0
da2: <FUJITSU MAG3091LC 5210> Fixed Direct Access SCSI-2 device
da2: Serial Number 00001305
da2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged
Queueing Enabled
da2: 8704MB (17827698 512 byte sectors: 255H 63S/T 1109C)
da1 at sym0 bus 0 target 1 lun 0
da1: <FUJITSU MAG3091LC 5210> Fixed Direct Access SCSI-2 device
da1: Serial Number 00002277
da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged
Queueing Enabled
da1: 8704MB (17827698 512 byte sectors: 255H 63S/T 1109C)
da0 at sym0 bus 0 target 0 lun 0
da0: <HP 18.2GB A 80-B005 B005> Fixed Direct Access SCSI-2 device
da0: Serial Number 3AK0A5ZJ000010071Z8W
da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged
Queueing Enabled
da0: 17366MB (35566480 512 byte sectors: 255H 63S/T 2213C)
(cd0:sym0:0:5:0): error 6
(cd0:sym0:0:5:0): Unretryable Error
cd0 at sym0 bus 0 target 5 lun 0
cd0: <NEC CD-ROM DRIVE:465 1.13> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY, Medium not
present
(cd0:sym0:0:5:0): error 6
(cd0:sym0:0:5:0): Unretryable Error
(cd0:sym0:0:5:0): error 6
(cd0:sym0:0:5:0): Unretryable Error
(cd0:sym0:0:5:0): error 6
(cd0:sym0:0:5:0): Unretryable Error
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:35551782
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 32256 length 18202512384 end 18202544639
GEOM: Configure da1c, start 0 length 9127781376 end 9127781375
GEOM: Configure da1d, start 32256 length 9127749120 end 9127781375
GEOM: Configure da2c, start 0 length 9127781376 end 9127781375
GEOM: Configure da2d, start 32256 length 9127749120 end 9127781375
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
GEOM: Configure da0s1a, start 0 length 123731968 end 123731967
GEOM: Configure da0s1b, start 123731968 length 1073741824 end
1197473791
GEOM: Configure da0s1c, start 0 length 18202512384 end 18202512383
GEOM: Configure da0s1d, start 1197473792 length 1073741824 end
2271215615
GEOM: Configure da0s1e, start 2271215616 length 2147483648 end
4418699263
GEOM: Configure da0s1f, start 4418699264 length 13783813120 end
18202512383
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:0e typ:162 s(CHS):256/82/1 e(CHS):458/238/17 s:-609674986 l:-
612337923
[1] f:20 typ:230 s(CHS):922/28/36 e(CHS):673/52/56 s:-1119163435 l:
234863854
[2] f:3a typ:203 s(CHS):351/90/10 e(CHS):519/233/51 s:-938304081 l:-
752965650
[3] f:73 typ:121 s(CHS):961/226/25 e(CHS):219/32/18 s:-278924650 l:-
898031409
Mounting root from ufs:/dev/da0s1a
start_init: trying /sbin/init
[0] f:0e typ:162 s(CHS):256/82/1 e(CHS):458/238/17 s:-609674986 l:-
612337923
[1] f:20 typ:230 s(CHS):922/28/36 e(CHS):673/52/56 s:-1119163435 l:
234863854
[2] f:3a typ:203 s(CHS):351/90/10 e(CHS):519/233/51 s:-938304081 l:-
752965650
[3] f:73 typ:121 s(CHS):961/226/25 e(CHS):219/32/18 s:-278924650 l:-
898031409
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 63
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 62
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 61
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 60
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 59
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 58
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 57
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 56
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 55
(da0:sym0:0:0:0): Retrying Command
(da0:sym0:0:0:0): QUEUE FULL
(da0:sym0:0:0:0): Queue Full
(da0:sym0:0:0:0): tagged openings now 54
(da0:sym0:0:0:0): Retrying Command
Kernel configuration file:
machine i386
cpu I686_CPU
ident AUSRINE
# IPfilter packet filter
options IPFILTER
options IPFILTER_LOG
# ALTQ
options ALTQ # enable ALTQ
options ALTQ_CBQ # build the ``Class Based
Queuing'' discipline.
#options ALTQ_RED # build the ``Random Early
Drop'' extension.
#options ALTQ_RIO # build ``Random Early Drop''
for input and output.
options ALTQ_HFSC # build the ``Hierarchical
Packet Scheduler'' discipline.
options ALTQ_CDNR # build the traffic
conditioner. This option is meaningless at
# the moment as the conditioner is
not used by any of the
# available disciplines or
consumer.
options ALTQ_PRIQ # build the ``Priority
Queuing'' discipline.
options ALTQ_NOPCC # required for SMP builds.
#options ALTQ_DEBUG # enable additional debugging
facilities.
makeoptions COPTFLAGS="-O2 -pipe -funroll-loops -ffast-math"
options SCHED_4BSD # 4BSD scheduler
options INET # InterNETworking
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates
support
options UFS_DIRHASH # Improve performance on big
directories
options MD_ROOT # MD is a potential root
device
options MSDOSFS # MSDOS Filesystem
options CD9660 # ISO 9660 Filesystem
options PROCFS # Process filesystem (requires
PSEUDOFS)
options PSEUDOFS # Pseudo-filesystem framework
options GEOM_GPT # GUID Partition Tables.
options COMPAT_43 # Compatible with BSD 4.3
[KEEP THIS!]
options COMPAT_FREEBSD4 # Compatible with FreeBSD4
options SCSI_DELAY=2000 # Delay (in ms) before probing
SCSI
options KTRACE # ktrace(1) support
options SYSVSHM # SYSV-style shared memory
options SYSVMSG # SYSV-style message queues
options SYSVSEM # SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time
extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in
debug
# output. Adds ~128k to
driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in
debug
# output. Adds ~215k to
driver.
options ADAPTIVE_GIANT # Giant mutex is adaptive.
# Enables building of a Symmetric MultiProcessor kernel:
options SMP
options NO_MIXED_MODE # Disable use of mixed mode
device apic # I/O APIC
# Bus support. Do not remove isa, even if you have no isa slots
device isa
device pci
# Floppy drives
device fdc
# SCSI Controllers
device sym # NCR/Symbios Logic (newer chipsets +
those of `ncr')
# SCSI peripherals
device scbus # SCSI bus (required for SCSI)
device ch # SCSI media changers
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI
access)
device ses # SCSI Environmental Services (and
SAF-TE)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device vga # VGA video card driver
# syscons is the default console driver, resembling an SCO console
device sc
# Floating point support - do not disable.
device npx
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppbus # Parallel port bus (required)
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these
NICs!
device miibus # MII bus support
device fxp
device dc # DEC/Intel 21143 and various
workalikes
# Pseudo devices.
device loop # Network loopback
device mem # Memory and kernel memory devices
device io # I/O device
device random # Entropy device
device ether # Ethernet support
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
# Note that 'bpf' is required for DHCP.
device bpf # Berkeley packet filter
# USB support
device usb # USB Bus (required)
More information about the freebsd-bugs
mailing list