CUPDS reboot the whole system

Todor Dragnev todor.dragnev at
Wed May 18 14:54:59 GMT 2005

On вт, 2005-05-17 at 15:30 -0700, Kris Kennaway wrote:
> On Wed, May 18, 2005 at 01:59:09PM +0300, Todor Dragnev wrote:
> > Hello,
> > 
> > Before a couple of days ago I started /usr/local/sbin/cupsd manualy from
> > console. When I press CTRL+C to interrupt a program, the system change
> > runlevel and going to reboot. This was on FreeBSD V5.3, today I
> > installed fresh new 5.4 but the problem is the same.
> > 
> > cups-base-
> Please transcribe exactly what is displayed after you press ^C.

> Kris

Nothing :(

Message shown in display is 
"The operating system is halted press any key to reboot"

Attached file contain console session before unexpected halt.

Todor Dragnev <todor.dragnev at>
-------------- next part --------------
iLux# killall cupsd
iLux# killall cupsd
No matching processes were found
iLux# /usr/local/sbin/cupsd 
iLux# dmesg
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE #0: Sun May  8 10:21:06 UTC 2005
    root at
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Celeron (801.83-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
real memory  = 402587648 (383 MB)
avail memory = 384253952 (366 MB)
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <VIA694 AWRDACPI> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU (3 Cx states)> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd0000000-0xd3ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596B UDMA66 controller> port 0xd000-0xd00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 10 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, HOST-PCI> at device 7.3 (no driver attached)
ed0: <NE2000 PCI Ethernet (ProLAN)> port 0xd800-0xd81f irq 5 at device 15.0 on pci0
ed0: Ethernet address: 48:54:e8:2b:97:b9
ed0: if_start running deferred for Giant
ed0: type NE2000 (16 bit) 
rl0: <RealTek 8139 10/100BaseTX> port 0xdc00-0xdcff mem 0xd9103000-0xd91030ff irq 5 at device 17.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 4c:00:10:a3:07:ce
rl1: <RealTek 8139 10/100BaseTX> port 0xe000-0xe0ff mem 0xd9100000-0xd91000ff irq 9 at device 18.0 on pci0
miibus1: <MII bus> on rl1
rlphy1: <RealTek internal media interface> on miibus1
rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl1: Ethernet address: 00:02:44:92:17:0a
uhci1: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 10 at device 19.0 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xe800-0xe81f irq 11 at device 19.1 on pci0
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 19.2 (no driver attached)
csa0: <CS4280/CS4614/CS4622/CS4624/CS4630> mem 0xd9000000-0xd90fffff,0xd9102000-0xd9102fff irq 11 at device 20.0 on pci0
csa: card is Unknown/invalid SSID (CS4614)
pcm0: <CS461x PCM Audio> on csa0
pcm0: <Cirrus Logic CS4294/98 AC97 Codec>
fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
orm0: <ISA Option ROMs> at iomem 0xcc000-0xcffff,0xc0000-0xca7ff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
umass0: USB2.0 External Mass Storage Device, rev 2.00/0.01, addr 2
umass0: Get Max Lun not supported (STALLED)
Timecounter "TSC" frequency 801825144 Hz quality 800
Timecounters tick every 10.000 msec
ad0: 16446MB <ST317221A/3.03> [33416/16/63] at ata0-master UDMA66
ad1: 152627MB <ST3160023A/8.01> [310101/16/63] at ata0-slave UDMA66
cd0 at umass-sim0 bus 0 target 0 lun 0
cd0: <LITE-ON DVDRW SOHW-1653S CS0M> Removable CD-ROM SCSI-0 device 
cd0: 1.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Mounting root from ufs:/dev/ad0s1a
IP Filter: v3.4.35 initialized.  Default = pass all, Logging = enabled
ipfw2 initialized, divert disabled, rule-based forwarding disabled, default to deny, logging disabled
Accounting enabled
arplookup failed: host is not on local network
ed0: promiscuous mode enabled
rl1: promiscuous mode enabled
arplookup failed: host is not on local network
arplookup failed: host is not on local network
iLux# Connection to fooolhost.fake closed by remote host.

More information about the freebsd-bugs mailing list