kern/56944: 4.8 cannot boot on Intel Server Board SE7501HG2with
SCSI enabled
Eugene Grosbein
eugen at kuzbass.ru
Wed Sep 17 02:30:18 PDT 2003
The following reply was made to PR kern/56944; it has been noted by GNATS.
From: Eugene Grosbein <eugen at kuzbass.ru>
To: bug-followup at FreeBSD.org
Cc:
Subject: Re: kern/56944: 4.8 cannot boot on Intel Server Board SE7501HG2 with
SCSI enabled
Date: Wed, 17 Sep 2003 17:21:56 +0800
Here is diff between dmesg.boot for unsuccessful boot attempt
(SCSI is enabled in the BIOS Setup) and successful one
(SCSI is disabled).
-- bad Wed Sep 17 17:19:18 2003
+++ ok Wed Sep 17 17:18:40 2003
@@ -3,7 +3,7 @@
The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RELEASE #0: Thu Apr 3 10:53:38 GMT 2003
root at freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
-Calibrating clock(s) ... TSC clock: 2657938544 Hz, i8254 clock: 1193114 Hz
+Calibrating clock(s) ... TSC clock: 2657931308 Hz, i8254 clock: 1193110 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
@@ -21,7 +21,7 @@
config> di aha0
config> di adv0
config> q
-avail memory = 1039847424 (1015476K bytes)
+avail memory = 1039826944 (1015456K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fdb20
bios32: Entry = 0xfdb34 (c00fdb34) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xdb55
@@ -35,7 +35,7 @@
Creating DISK md0
md0: Malloc disk
Math emulator present
-pci_open(1): mode 1 addr port (0x0cf8) is 0x80032000
+pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=254c8086)
Using $PIR table, 18 entries at 0xc00f3590
@@ -99,64 +99,24 @@
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 64, base fea60000, size 17
- map[20]: type 1, range 32, base 00003040, size 6
+ map[20]: type 1, range 32, base 00002040, size 6
found-> vendor=0x8086, dev=0x1010, revid=0x01
class=02-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=9
map[10]: type 1, range 64, base fea80000, size 17
- map[20]: type 1, range 32, base 00003000, size 6
+ map[20]: type 1, range 32, base 00002000, size 6
pci4: <PCI bus> on pcib2
-em0: <Intel(R) PRO/1000 Network Connection, Version - 1.4.10> port
0x3040-0x307f mem
0xfea60000-0xfea7ffff irq 9 at device 5.0 on pci4
+em0: <Intel(R) PRO/1000 Network Connection, Version - 1.4.10> port
0x2040-0x207f mem
0xfea60000-0xfea7ffff irq 9 at device 5.0 on pci4
bpf: em0 attached
em0: Speed:N/A Duplex:N/A
-em1: <Intel(R) PRO/1000 Network Connection, Version - 1.4.10> port
0x3000-0x303f mem
0xfea80000-0xfea9ffff irq 9 at device 5.1 on pci4
+em1: <Intel(R) PRO/1000 Network Connection, Version - 1.4.10> port
0x2000-0x203f mem
0xfea80000-0xfea9ffff irq 9 at device 5.1 on pci4
using shared irq9.
bpf: em1 attached
em1: Speed:N/A Duplex:N/A
pci2: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci2
-found-> vendor=0x9005, dev=0x801f, revid=0x03
- class=01-00-00, hdrtype=0x00, mfdev=1
- subordinatebus=0 secondarybus=0
- intpin=a, irq=9
- map[10]: type 1, range 32, base 00002800, size 8
- map[14]: type 1, range 64, base fe9e0000, size 13
- map[1c]: type 1, range 32, base 00002c00, size 8
-found-> vendor=0x9005, dev=0x801f, revid=0x03
- class=01-00-00, hdrtype=0x00, mfdev=1
- subordinatebus=0 secondarybus=0
- intpin=b, irq=9
- map[10]: type 1, range 32, base 00002000, size 8
- map[14]: type 1, range 64, base fe9f0000, size 13
- map[1c]: type 1, range 32, base 00002400, size 8
pci3: <PCI bus> on pcib3
-ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0x2c00-0x2cff,0x2800-0x28ff mem
0xfe9e0000-0xfe9e1fff irq 9 at device 4.0 on pci3
-ahd0: Defaulting to MEMIO on
-ahd0: Reading SEEPROM...done.
-ahd0: STPWLEVEL is on
-ahd0: Manual Primary Termination
-ahd0: Manual Secondary Termination
-ahd0: Primary High byte termination Enabled
-ahd0: Primary Low byte termination Enabled
-ahd0: Secondary High byte termination Disabled
-ahd0: Secondary Low byte termination Disabled
-ahd0: Downloading Sequencer Program... 716 instructions downloaded
-ahd0: Features 0x101, Bugs 0xfffff, Flags 0x43f0
-aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
-ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0x2400-0x24ff,0x2000-0x20ff mem
0xfe9f0000-0xfe9f1fff irq 9 at device 4.1 on pci3
-ahd1: Defaulting to MEMIO on
-ahd1: Reading SEEPROM...done.
-ahd1: STPWLEVEL is on
-ahd1: Manual Primary Termination
-ahd1: Manual Secondary Termination
-ahd1: Primary High byte termination Enabled
-ahd1: Primary Low byte termination Enabled
-ahd1: Secondary High byte termination Disabled
-ahd1: Secondary Low byte termination Disabled
-ahd1: Downloading Sequencer Program... 716 instructions downloaded
-ahd1: Features 0x101, Bugs 0xfffff, Flags 0x43f0
-aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
pci0: <unknown card> (vendor=0x8086, dev=0x2546) at 3.1
pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
found-> vendor=0x1002, dev=0x4752, revid=0x27
@@ -188,3 +148,112 @@
ata1: devices=08
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 0
+ex_isa_identify()
+ata-: ata0 exists, using next available unit number
+ata-: ata1 exists, using next available unit number
+Trying Read_Port at 203
+Trying Read_Port at 243
+Trying Read_Port at 283
+Trying Read_Port at 2c3
+Trying Read_Port at 303
+Trying Read_Port at 343
+Trying Read_Port at 383
+Trying Read_Port at 3c3
+isa_probe_children: disabling PnP devices
+isa_probe_children: probing non-PnP devices
+orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff,0xe4000-0xe7fff
on isa0
+fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
+fdc0: FIFO enabled, 8 bytes threshold
+fd0: <1440-KB 3.5" drive> on fdc0 drive 0
+ata2 failed to probe at port 0x1f0 irq 14 on isa0
+ata3 failed to probe at port 0x170 irq 15 on isa0
+adv0: not probed (disabled)
+bt0: not probed (disabled)
+aha0: not probed (disabled)
+aic0: not probed (disabled)
+atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
+atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
+atkbd: the current kbd controller command byte 0065
+atkbd: keyboard ID 0x41ab (2)
+kbd0 at atkbd0
+kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
+vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
+fb0: vga0, vga, type:VGA (5), flags:0x7007f
+fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
+fb0: init mode:24, bios mode:3, current mode:24
+fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
+VGA parameters upon power-up
+50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
+bf 1f 00 4f 0d 0e 00 00 05 f0 9c 8e 8f 28 1f 96
+b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
+3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
+VGA parameters in BIOS for mode 24
+50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
+bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
+b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
+3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
+EGA/VGA parameters to be used for mode 24
+50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
+bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
+b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
+3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
+sc0: <System console> at flags 0x100 on isa0
+sc0: VGA <16 virtual consoles, flags=0x300>
+sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
+pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
+pcic1: not probed (disabled)
+sio0: irq maps: 0x3 0x13 0x3 0x3
+sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
+sio0: type 16550A
+sio1: irq maps: 0x3 0xb 0x3 0x3
+sio1 at port 0x2f8-0x2ff irq 3 on isa0
+sio1: type 16550A
+sio2: not probed (disabled)
+sio3: not probed (disabled)
+ppc0: parallel port found at 0x378
+ppc0: using extended I/O port range
+ppc0: ECP SPP SPP
+ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
+ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
+ppc0: FIFO with 16/16/8 bytes threshold
+plip0: <PLIP network interface> on ppbus0
+bpf: lp0 attached
+lpt0: <Printer> on ppbus0
+lpt0: Interrupt-driven port
+ppi0: <Parallel I/O> on ppbus0
+ed0: not probed (disabled)
+fe0: not probed (disabled)
+ie0: not probed (disabled)
+lnc0: not probed (disabled)
+cs0: not probed (disabled)
+sn0: not probed (disabled)
+isa_probe_children: probing PnP devices
+BIOS Geometries:
+ 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
+ 0 accounted for
+Device configuration finished.
+bpf: faith0 attached
+bpf: lo0 attached
+bpf: ppp0 attached
+new masks: bio 68c040, tty 63009a, net 67029a
+bpf: sl0 attached
+ad0: success setting UDMA5 on Intel chip
+Creating DISK ad0
+ar: FreeBSD check1 failed
+ad0: <Maxtor 6Y120P0/YAR41BW0> ATA-7 disk at ata0-master
+ad0: 117246MB (240121728 sectors), 238216 C, 16 H, 63 S, 512 B
+ad0: 16 secs/int, 1 depth queue, UDMA100
+ad0: piomode=4 dmamode=2 udmamode=6 cblid=1
+ata1-slave: piomode=4 dmamode=2 udmamode=2 dmaflag=1
+ata1-slave: success setting PIO4 on generic chip
+acd0: <SONY CD-RW CRX225E/QYB1> CD-RW drive at ata1 as slave
+acd0: read 22516KB/s (53284KB/s) write 172KB/s (8958KB/s), 2048KB buffer,
PIO4
+acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
+acd0: Writes: CD-R, CD-RW, test write, burnproof
+acd0: Audio: play, 255 volume levels
+acd0: Mechanism: ejectable tray, unlocked
+acd0: Medium: no/blank disc
+Mounting root from ufs:/dev/ad0s2a
+ad0s1: type 0x12, start 63, end = 80324, size 80262 : OK
+ad0s2: type 0xa5, start 80325, end = 240107489, size 240027165 : OK
+start_init: trying /sbin/init
Eugene Grosbein
More information about the freebsd-bugs
mailing list