Kirkwood problem

Sat Feb 9 05:48:05 UTC 2019

Hi

----- Original Message -----
> From: Mori Hiroki <yamori813 at yahoo.co.jp>
> To: Ronald Klop <ronald-lists at klop.ws>
> Cc: "freebsd-arm at freebsd.org" <freebsd-arm at freebsd.org>
> Date: 2019/2/8, Fri 20:23
> Subject: Re: Kirkwood problem
> 
> Hi
> 
> Thanks for your reply.
> 
> My dmesg is this.
> 
> https://dmesgd.nycbug.org/index.cgi?do=view&id=4763 
> 
> I use ZRouter build system and use USB memory.
> 
> RT1310(armv5t 300MHZ) mruby fib(32) is 145 sec. 
> 
> 88E6281(armv5t 1.2GHz) mruby fib(32) is 232 sec.

I installed debian and check mruby fib(32).

It's only 9 sec.

FreeBSD is 25 times slow...

> 
> This is very strange.
> 
> 
> I try to debug mge. I found DMA failed. NO send and
> receive packet. But I don't know reason.
> 
> 
> Hiroki Mori
> 
> 
> ----- Original Message -----
>> From: Ronald Klop <ronald-lists at klop.ws>
>> To: Mori Hiroki <yamori813 at yahoo.co.jp> 
>> Cc: "freebsd-arm at freebsd.org" <freebsd-arm at freebsd.org>
>> Date: 2019/2/6, Wed 23:38
>> Subject: Re: Kirkwood problem
>> 
>> 
>>   
>> Van: Mori Hiroki <yamori813 at yahoo.co.jp>
>> Datum: woensdag, 6 februari 2019 10:21
>> Aan: "freebsd-arm at freebsd.org" <freebsd-arm at freebsd.org>
>> Onderwerp: Kirkwood problem
>> Hi
>>> 
>>> I try to OpenRD like device on 13-CURRENT.
>>> 
>>> This is Marvell Kirkwood.
>>> 
>>> This is armv5t but have 512M byte ram and 1.2G
>>> clock.
>>> 
>>> I have two problem.
>>> 
>>> This device have 88F6281 and 88E1116R phy on mac.
>>> 
>>> But not work mge.
>>> 
>>> Second is very slow mruby fib(32) benchmark.
>>> 
>>> I think this target u-boot not optimize memory
>>> controller.
>>> 
>>> If you have advice, please let me know.
>>> 
>>> 
>>> Thanks
>>> 
>>> Hiroki Mori
>>>  
>> This sounds like my Sheevaplug.
>> See https://wiki.freebsd.org/FreeBSD/arm/Kirkwood 
>> 
>> Mine runs 11.2 currently and I successfully booted 12.0 on it. I don't 
> know about current, but I haven't seen removal of support for this device 
> yet.
>> See dmesg below.
>> Network mge works for me. It is slow. But also very old. I don't think a 
> lot can be done about the speed. (But I'm not the developer of this port.)
>> 
>> Do you get it to boot properly? Is there an error about the mge network 
> adapter not working?
>> Any significant output in /var/log/messages?
>> 
>> Regards,
>> Ronald.
>> 
>> Copyright (c) 1992-2018 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>>         The Regents of the University of California. All rights reserved.
>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>> FreeBSD 11.2-RELEASE-p4 #4 r339336M: Sat Oct 13 23:31:51 CEST 2018
>>     builder at rpi3:/data/src/obj-11.2/arm.arm/data/src/11.2/sys/SHEEVAPLUG arm
>> FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 
> 6.0.0)
>> CPU: Feroceon 88FR131 rev 1 (**unknown 4** core)
>>   Little-endian DC enabled IC disabled WA disabled DC streaming enabled
>>   BTB disabled L2 enabled L2 prefetch enabled
>>   WB enabled LABT branch prediction disabled
>>   16KB/32B 4-way instruction cache
>>   16KB/32B 4-way write-back-locking-C data cache
>> real memory  = 536866816 (511 MB)
>> avail memory = 518819840 (494 MB)
>> SOC: Marvell 88F6281 rev A0, TClock 200MHz
>>   Instruction cache prefetch enabled, data cache prefetch enabled
>>   256KB 4-way set-associative write-through unified L2 cache
>> random: entropy device external interface
>> ofwbus0: <Open Firmware Device Tree>
>> simplebus0: <Flattened device tree simple bus> on ofwbus0
>> cpulist0: <Open Firmware CPU Group> on ofwbus0
>> cpu0: <Open Firmware CPU> on cpulist0
>> localbus0: <Marvell device bus> on ofwbus0
>> nand0: <Marvell NAND controller> mem 0xf9300000-0xf93fffff on 
> localbus0
>> nandbus0: <NAND bus> on nand0
>> lnand0: <Samsung NAND 512MiB 3,3V 8-bit> on nandbus0
>> lnand0: Found BBT table for chip
>> ic0: <Marvell Integrated Interrupt Controller> mem 0x20200-0x2023b on 
> simplebus0
>> timer0: <Marvell CPU Timer> mem 0x20300-0x2032f irq 1 on simplebus0
>> Event timer "CPUTimer0" frequency 200000000 Hz quality 1000
>> Timecounter "CPUTimer1" frequency 200000000 Hz quality 1000
>> gpio0: <Marvell Integrated GPIO Controller> mem 0x10100-0x1011f irq 
> 35,36,37,38,39,40,41 on simplebus0
>> rtc0: <Marvell Integrated RTC> mem 0x10300-0x10307 on simplebus0
>> rtc0: registered as a time-of-day clock, resolution 1.000000s
>> mge0: <Marvell Gigabit Ethernet controller> mem 0x72000-0x73fff irq 
> 12,13,14,11,46 on simplebus0
>> mge0: PHY0 attached, phy_sc points to mge0
>> mge0: Ethernet address: 00:50:43:01:6f:12
>> miibus0: <MII bus> on mge0
>> e1000phy0: <Marvell 88E1116R Gigabit PHY> PHY 0 on miibus0
>> e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
> 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
>> uart0: <16550 or compatible> mem 0x12000-0x1201f irq 33 on simplebus0
>> uart0: console (1066,n,8,1)
>> uart1: <16550 or compatible> mem 0x12100-0x1211f irq 34 on simplebus0
>> cesa0: <Marvell Cryptographic Engine and Security Accelerator> mem 
> 0x30000-0x30fff,0x3d000-0x3dfff irq 22 on simplebus0
>> ehci0: <Marvell Integrated USB 2.0 controller> mem 0x50000-0x50fff irq 
> 48,19 on simplebus0
>> usbus0: EHCI version 1.0
>> usbus0 on ehci0
>> cryptosoft0: <software crypto>
>> Timecounters tick every 1.000 msec
>> usbus0: 480Mbps High Speed USB v2.0
>> ugen0.1: <Marvell EHCI root HUB> at usbus0
>> uhub0: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on 
> usbus0
>> bootpc_init: wired to interface 'mge0'
>> Sending DHCP Discover packet from interface mge0 (00:50:43:01:6f:12)
>> Received DHCP Offer packet on mge0 from 0.0.0.0 (accepted)
>> uhub0: 1 port with 1 removable, self powered
>> mge0: link state changed to UP
>> ugen0.2: <vendor 0x0930 USB Flash Memory> at usbus0
>> umass0 on uhub0
>> umass0: <vendor 0x0930 USB Flash Memory, class 0/0, rev 2.00/1.10, addr 
> 2> on usbus0
>> da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
>> da0: < USB Flash Memory PMAP> Removable Direct Access SCSI device
>> da0: Serial Number 001D92AD6ADAB910B3230034
>> da0: 40.000MB/s transfers
>> da0: 15320MB (31375360 512 byte sectors)
>> da0: quirks=0x2<NO_6_BYTE>
>> Sending DHCP Request packet from interface mge0 (00:50:43:01:6f:12)
>> Received DHCP Ack packet on mge0 from 0.0.0.0 (accepted)
>> mge0 at 192.168.1.105 server 0.0.0.0
>> subnet mask 255.255.255.0 router 192.168.1.254
>> Adjusted interface mge0
>> Trying to mount root from ufs:/dev/da0s1a []...
>> WARNING: / was not properly dismounted
>> WARNING: / was not properly dismounted
>> random: unblocking device.
>> ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to deny, 
> logging disabled
>> 
>> 
>>  
>> 
>> 
> 
> _______________________________________________
> freebsd-arm at freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm 
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe at freebsd.org"
> 