any progress with OrangePi Plus / AllWinner H3 ?

[Emmanuel Vadot]

 There seems to be a problem with HIGH speed device but not every time

 On orangepi I successfully used :
 - An Optical mouse (LOW speed device)
 - An FDTI usb adapter (FULL speed device)
 - An usb 3.0 thumb drive (HIGH speed device)

ugen1.2: <Logitech> at usbus1
ums0: <Logitech Optical USB Mouse, class 0/0, rev 2.00/3.40, addr 2> on
usbus1 ums0: 3 buttons and [XYZ] coordinates ID=0
root at allwinner:~ # usbconfig 
ugen0.1: <EHCI root HUB Allwinner> at usbus0, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (0mA)
ugen1.1: <OHCI root HUB Generic> at usbus1, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=SAVE (0mA)
ugen1.2: <Optical USB Mouse Logitech> at usbus1, cfg=0 md=HOST spd=LOW
(1.5Mbps) pwr=ON (100mA)

ugen1.2: <FTDI> at usbus1
uftdi0: <TTL232R-3V3> on usbus1
root at allwinner:~ # usbconfig
ugen0.1: <EHCI root HUB Allwinner> at usbus0, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (0mA)
ugen1.1: <OHCI root HUB Generic> at usbus1, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=SAVE (0mA)
ugen1.2: <TTL232R-3V3FTDI> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps)
pwr=ON (90mA)

ugen0.2: <Corsair> at usbus0
umass0: <Corsair Voyager Mini 3.0, class 0/0, rev 2.10/1.10, addr 2> on
usbus0 umass0:  SCSI over Bulk-Only; quirks = 0x8100
umass0:0:0: Attached to scbus0
da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
da0: <Corsair Voyager Mini 3.0 PMAP> Removable Direct Access SPC-4 SCSI
device da0: Serial Number 07083C762390FF02
da0: 40.000MB/s transfers
da0: 59082MB (120999936 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
GEOM: da0: the secondary GPT header is not in the last LBA.
GEOM: diskid/DISK-07083C762390FF02: the secondary GPT header is not in
the last LBA.

root at allwinner:~ # usbconfig 
ugen0.1: <EHCI root HUB Allwinner> at usbus0, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (0mA)
ugen1.1: <OHCI root HUB Generic> at usbus1, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=SAVE (0mA)
ugen0.2: <Voyager Mini 3.0 Corsair> at usbus0, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=ON (300mA)

But as soon as I unplug my usb thumb drive I have a hard time to attach
a HIGH speed device after, I need to wait ~1 min before plugin a new
device so that it works again.

I also have the problem on my laptop (running ALPHA3) so it's not
arm/allwinner related.

On Sat, 18 Jun 2016 11:00:41 +0200
Emmanuel Vadot <manu at bidouilliste.com> wrote:

> On Sat, 18 Jun 2016 10:23:38 +0200
> Emmanuel Vadot <manu at bidouilliste.com> wrote:
> 
> > > Also, USB spams console with
> > > 
> > > gic0: Spurious interrupt detected: last irq: 107 on CPU0
> > > usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR,
> > > ignored) usbd_setup_device_desc: getting device descriptor at addr 2
> > > failed, USB_ERR_IOERROR usbd_req_re_enumerate: addr=2, set address
> > > failed! (USB_ERR_IOERROR, ignored) usbd_setup_device_desc: getting
> > > device descriptor at addr 2 failed, USB_ERR_IOERROR
> > > usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR,
> > > ignored) usbd_setup_device_desc: getting device descriptor at addr 2
> > > failed, USB_ERR_IOERROR
> > > 
> > > (sorry mailer mangled this, but I do not expect anyone to analyze this
> > > as there *are* working sources available for this... yours)
> > > 
> > > From your tests, which devices are not working yet? Do you have any
> > > plans what to work on next?
> > 
> >  I'll test USB again, it used to work at least.
> 
>  I do see the same stuff, it doesn't happened everytime thought.
>  I'll try to find the problem.
> 
> -- 
> Emmanuel Vadot
> _______________________________________________
> freebsd-arm at freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe at freebsd.org"


-- 
Emmanuel Vadot