Odroidc1+ stuck booting
Daniel Braniss
danny at cs.huji.ac.il
Sun Apr 10 08:59:32 UTC 2016
Hi
> On 9 Apr 2016, at 22:52, Weiß, Dr. Jürgen <weiss at uni-mainz.de> wrote:
>
> Hi,
>
> I have a C1+ and just booted a FreeBSD current kernel not older than
> a week without problems.
>
> fatload mmc 0:1 0x21000000 kernel.bin
> go 0x21000000
>
my kernel loads at a different address!
btw, what kernconf are you using? I had to comment out the random
stuff, since it was giving compiler errors.
> Maybe you could try a different sd card, as it seems to get stuck at
> a time when it is probing the sd cards.
it’s booting from it, and i have tried several cards, BTW, it
also gives the same error when booting from the net.
my guts make me think it’s in the *dtb stuff. which is loaded into
the kernel and not read of the sd card.
thanks,
danny
>
> Regards
>
> Juergen
>
>
>
>> -----Original Message-----
>> From: owner-freebsd-arm at freebsd.org [mailto:owner-freebsd-arm at freebsd.org] On Behalf Of
>> Erik Moe
>> Sent: Tuesday, April 05, 2016 10:53 PM
>> To: Daniel Braniss
>> Cc: freebsd-arm
>> Subject: Re: Odroidc1+ stuck booting
>>
>> That’s correct I have a C1, not a C1+.
>>
>> Erik
>>
>>> On Apr 4, 2016, at 6:02 AM, Daniel Braniss <danny at cs.huji.ac.il> wrote:
>>>
>>> I assume you have a C1 not a C1+, because I’m doing the same,
>>> and no luck. I know that the board is ok because It boots and runs Daisuke-san’s image.
>>> danny
>>>
>>>> On 31 Mar 2016, at 15:29, Erik Moe <e.moe at rcn.com> wrote:
>>>>
>>>> Everything I’m doing I “borrowed” from here:
>> https://wiki.freebsd.org/FreeBSD/arm/Odroid-C1
>>>>
>>>> I’m using the stock ODROIDC1 kernel config in head which builds the FTD statically into
>> the kernel from src/sys/boot/fdt/dts/arm/odroidc1.dts. I liberated u-boot from
>> ArchLinuxARM-odroid-c1-latest.tar.gz. My boot.ini is simply this:
>>>>
>>>> ODROIDC-UBOOT-CONFIG
>>>>
>>>> setenv bootcmd "fatload mmc 0 0x100000 kernel.bin; go 0x100000"
>>>> run bootcmd
>>>>
>>>> Erik
>>>>
>>>>> On Mar 31, 2016, at 1:36 AM, Daniel Braniss <danny at cs.huji.ac.il> wrote:
>>>>>
>>>>> oh, and if you feel generous your ODROIDC1.conf …
>>>>> thanks,
>>>>> danny
>>>>>
>>>>>> On 31 Mar 2016, at 09:31, Daniel Braniss <danny at cs.huji.ac.il> wrote:
>>>>>>
>>>>>> hi Erik,
>>>>>> can you send me your
>>>>>> uboot
>>>>>> boot.ini
>>>>>> *.dtb
>>>>>> I’m pretty sure the issue is somewhere there then.
>>>>>> thanks,
>>>>>> danny
>>>>>>
>>>>>>> On 31 Mar 2016, at 09:11, Erik Moe <e.moe at rcn.com> wrote:
>>>>>>>
>>>>>>> I built a new image for my odriod-c1 for ssd from the latest sources and had no
>> issues and didn’t need to tweet anything. I don’t have and odriod-c1+, but my
>> understanding is there isn’t much difference between the two. I am using the serial
>> console.
>>>>>>>
>>>>>>> QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PASS:1;
>>>>>>> -----------------------------------------------------------------------
>>>>>>> * Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec 8 2014) *
>>>>>>> -----------------------------------------------------------------------
>>>>>>> CPU : AMLogic S805
>>>>>>> MEM : 1024MB (DDR3 at 792MHz)
>>>>>>> BID : HKC13C0001
>>>>>>> S/N : HKC1CC037EBE4620
>>>>>>> 0x0000009f
>>>>>>> check SD_boot_type:0x1 card_type:0x1
>>>>>>> Loading U-boot...success.
>>>>>>>
>>>>>>>
>>>>>>> U-boot(odroidc@) (Jun 12 2015 - 17:31:14)
>>>>>>>
>>>>>>> DRAM: 1 GiB
>>>>>>> relocation Offset is: 2ff1c000
>>>>>>> MMC: SDCARD: 0, eMMC: 1
>>>>>>> IR init is done!
>>>>>>> vpu clk_level = 3
>>>>>>> set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
>>>>>>> mode = 6 vic = 4
>>>>>>> set HDMI vic: 4
>>>>>>> mode is: 6
>>>>>>> viu chan = 1
>>>>>>> config HPLL
>>>>>>> config HPLL done
>>>>>>> reconfig packet setting done
>>>>>>> MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks read: OK
>>>>>>> There is no valid bmp file at the given address
>>>>>>> ============================================================
>>>>>>> Vendor: Man 035344 Snr 29cfee4e Rev: 8.0 Prod: SL08G
>>>>>>> Type: Removable Hard Disk
>>>>>>> Capacity: 7580.0 MB = 7.4 GB (15523840 x 512)
>>>>>>> ------------------------------------------------------------
>>>>>>> Partition Start Sector Num Sectors Type
>>>>>>> 1 1134 131040 6
>>>>>>> 2 132174 15391666 a5
>>>>>>> ============================================================
>>>>>>> Net: Meson_Ethernet
>>>>>>> init suspend firmware done. (ret:0)
>>>>>>> Hit Enter key to stop autoboot -- : 0
>>>>>>> exit abortboot: 0
>>>>>>> reading boot.ini
>>>>>>>
>>>>>>> 98 bytes read
>>>>>>> Loading boot.ini from mmc0:1 (vfat)
>>>>>>> Executing the script...
>>>>>>> setenv bootcmd "fatload mmc 0 0x100000 kernel.bin; go 0x100000"
>>>>>>> run bootcmd
>>>>>>> reading kernel.bin
>>>>>>>
>>>>>>> 6055396 bytes read
>>>>>>> ## Starting application at 0x00100000 ...
>>>>>>> ARM Debug Architecture v7
>>>>>>> 2 watchpoints and 3 breakpoints supported
>>>>>>> KDB: debugger backends: ddb
>>>>>>> KDB: current backend: ddb
>>>>>>> Copyright (c) 1992-2016 The FreeBSD Project.
>>>>>>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>>>>>>> The Regents of the University of California. All rights reserved.
>>>>>>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>>>>>>> FreeBSD 11.0-CURRENT #4 43026a8(master)-dirty: Thu Mar 31 04:14:32 CDT 2016
>>>>>>> root at dora:/usr/home/emoe/Projects/ARM/odroid-
>> c1/obj/arm.armv6hf/usr/home/emoe/Projects/ARM/src/sys/ODROIDC1 arm
>>>>>>> FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on LLVM 3.8.0)
>>>>>>> WARNING: WITNESS option enabled, expect reduced performance.
>>>>>>> VT: init without driver.
>>>>>>> Preloaded elf kernel "kernel" at 0xc07c5d6c.
>>>>>>> CPU: Cortex A5 rev 1 (Cortex-A core)
>>>>>>> Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext
>>>>>>> WB enabled LABT branch prediction disabled
>>>>>>> LoUU:2 LoC:2 LoUIS:2
>>>>>>> Cache level 1:
>>>>>>> 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc
>>>>>>> 32KB/32B 2-way instruction cache Read-Alloc
>>>>>>> real memory = 1073737728 (1023 MB)
>>>>>>> avail memory = 1038233600 (990 MB)
>>>>>>> Physical memory chunk(s):
>>>>>>> 0x00001000 - 0x3fffffff, 1023 MB ( 262143 pages)
>>>>>>> Excluded memory regions:
>>>>>>> 0x00100000 - 0x00853fff, 7 MB ( 1876 pages) NoAlloc
>>>>>>> Static device mappings:
>>>>>>> 0xc1100000 - 0xc12fffff mapped at VA 0xffd00000
>>>>>>> 0xc4200000 - 0xc42fffff mapped at VA 0xffc00000
>>>>>>> 0xc4300000 - 0xc43fffff mapped at VA 0xffb00000
>>>>>>> 0xc8000000 - 0xc80fffff mapped at VA 0xffa00000
>>>>>>> 0xc8100000 - 0xc81fffff mapped at VA 0xff900000
>>>>>>> 0xc9000000 - 0xc97fffff mapped at VA 0xff100000
>>>>>>> 0xd9000000 - 0xd90fffff mapped at VA 0xff000000
>>>>>>> 0xda000000 - 0xda0fffff mapped at VA 0xfef00000
>>>>>>> Amlogic aml8726-m8b SoC
>>>>>>> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>>>>>>> ULE: setup cpu 0
>>>>>>> ULE: setup cpu 1
>>>>>>> ULE: setup cpu 2
>>>>>>> ULE: setup cpu 3
>>>>>>> random: entropy device external interface
>>>>>>> null: <full device, null device, zero device>
>>>>>>> openfirm: <Open Firmware control device>
>>>>>>> mem: <memory>
>>>>>>> nfslock: pseudo-device
>>>>>>> crypto: <crypto core>
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from nexus0
>>>>>>> ofwbus0: <Open Firmware Device Tree>
>>>>>>> simplebus0: <Flattened device tree simple bus> on ofwbus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from simplebus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from ofwbus0
>>>>>>> clkmsr0: <Amlogic aml8726 clkmsr> mem 0xc1108758-0xc1108767 on simplebus0
>>>>>>> clkmsr0: bus clock 159 MHz
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from clkmsr0
>>>>>>> l2cache0: <PL310 L2 cache controller> mem 0xc4200000-0xc4200fff irq 0 on ofwbus0
>>>>>>> l2cache0: Part number: 0x3, release: 0x9
>>>>>>> l2cache0: L2 Cache enabled: 512KB/32B 8 ways
>>>>>>> l2cache0: Early BRESP response: disabled
>>>>>>> l2cache0: Instruction prefetch: disabled
>>>>>>> l2cache0: Data prefetch: enabled
>>>>>>> l2cache0: Non-secure interrupt control: disabled
>>>>>>> l2cache0: Non-secure lockdown: disabled
>>>>>>> l2cache0: Share override: disabled
>>>>>>> l2cache0: Double linefill: disabled
>>>>>>> l2cache0: Instruction prefetch: disabled
>>>>>>> l2cache0: Data prefetch: enabled
>>>>>>> l2cache0: Double linefill on WRAP request: disabled
>>>>>>> l2cache0: Prefetch drop: disabled
>>>>>>> l2cache0: Incr double Linefill: disabled
>>>>>>> l2cache0: Not same ID on exclusive sequence: disabled
>>>>>>> l2cache0: Prefetch offset: 0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from l2cache0
>>>>>>> scu0: <ARM Snoop Control Unit> mem 0xc4300000-0xc4300fff on simplebus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from scu0
>>>>>>> cpuconfig0: <Amlogic CPU Config> mem 0xd901ff80-0xd901ff8f on simplebus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from cpuconfig0
>>>>>>> ccm0: <Amlogic aml8726 ccm> mem 0xc1104140-0xc1104153 on simplebus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from ccm0
>>>>>>> pinctrl0: <Amlogic aml8726 pinctrl> mem 0xc11080b0-0xc11080d7,0xc11080e8-
>> 0xc11080ff,0xc1108120-0xc1108137,0xc8100014-0xc8100017,0xc810002c-0xc810002f,0xc810002c-
>> 0xc810002f on simplebus0
>>>>>>> Processing 3 pin-config node(s) in pinctrl-0 for pinctrl at c11080b0
>>>>>>> Processing 1 pin-config node(s) in pinctrl-0 for mmc at c1108c20
>>>>>>> Processing 1 pin-config node(s) in pinctrl-0 for sdxc at c1108e00
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from pinctrl0
>>>>>>> gic0: <ARM Generic Interrupt Controller> mem 0xc4301000-0xc4301fff,0xc4300100-
>> 0xc43001ff on ofwbus0
>>>>>>> ofwbus0: no default resources for rid = 0, type = 1
>>>>>>> gic0: pn 0x390, arch 0x1, rev 0x1, implementer 0x43b irqs 256
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gic0
>>>>>>> wdt0: <Amlogic aml8726 WDT> mem 0xc1109900-0xc1109907 irq 2 on simplebus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from wdt0
>>>>>>> timer0: <Amlogic aml8726 timer> mem 0xc1109940-0xc1109957 irq 1 on ofwbus0
>>>>>>> Event timer "aml8726 timer A" frequency 1000000 Hz quality 1000
>>>>>>> Timecounter "aml8726 timer E" frequency 1000000 Hz quality 1000
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from timer0
>>>>>>> uart0: <Amlogic aml8726 UART> mem 0xc81004c0-0xc81004d7 irq 3 on simplebus0
>>>>>>> uart0: RTS iflow, CTS oflow
>>>>>>> uart0: console (115200,n,8,1)
>>>>>>> uart0: fast interrupt
>>>>>>> uart0: PPS capture mode: DCDinvalid
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from uart0
>>>>>>> uart1: <Amlogic aml8726 UART> mem 0xc11084c0-0xc11084d7 irq 4 on simplebus0
>>>>>>> uart1: RTS iflow, CTS oflow
>>>>>>> uart1: fast interrupt
>>>>>>> uart1: PPS capture mode: DCDinvalid
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from uart1
>>>>>>> uart2: <Amlogic aml8726 UART> mem 0xc11084dc-0xc11084f3 irq 5 on simplebus0
>>>>>>> uart2: RTS iflow, CTS oflow
>>>>>>> uart2: fast interrupt
>>>>>>> uart2: PPS capture mode: DCDinvalid
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from uart2
>>>>>>> uart3: <Amlogic aml8726 UART> mem 0xc1108700-0xc1108717 irq 6 on simplebus0
>>>>>>> uart3: RTS iflow, CTS oflow
>>>>>>> uart3: fast interrupt
>>>>>>> uart3: PPS capture mode: DCDinvalid
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from uart3
>>>>>>> simplebus0: <i2c at c8100500> mem 0xc8100500-0xc810051f irq 7 disabled compat
>> amlogic,meson6-i2c (no driver attached)
>>>>>>> aml8726_iic0: <Amlogic aml8726 I2C> mem 0xc1108500-0xc110851f irq 8 on simplebus0
>>>>>>> iicbb0: <I2C bit-banging driver> on aml8726_iic0
>>>>>>> iicbus0: <Philips I2C bus> on iicbb0 master-only
>>>>>>> iic0: <I2C generic I/O> on iicbus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from iic0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from iicbus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from iicbb0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_iic0
>>>>>>> aml8726_iic1: <Amlogic aml8726 I2C> mem 0xc11087c0-0xc11087df irq 9 on simplebus0
>>>>>>> iicbb1: <I2C bit-banging driver> on aml8726_iic1
>>>>>>> iicbus1: <Philips I2C bus> on iicbb1 master-only
>>>>>>> iic1: <I2C generic I/O> on iicbus1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from iic1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from iicbus1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from iicbb1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_iic1
>>>>>>> simplebus0: <ir-receiver at c8100480> mem 0xc8100480-0xc810049f irq 10 disabled compat
>> amlogic,meson6-ir (no driver attached)
>>>>>>> simplebus0: <spi at c1108c80> mem 0xc1108c80-0xc1108cff disabled compat amlogic,meson6-
>> spifc (no driver attached)
>>>>>>> simplebus0: <ethernet at c9410000> mem 0xc9410000-0xc941ffff,0xc1108108-0xc110810b irq
>> 11 disabled compat amlogic,meson6-dwmac (no driver attached)
>>>>>>> rtc0: <Amlogic aml8726 RTC> mem 0xc8100740-0xc8100753 irq 12 on simplebus0
>>>>>>> rtc0: crystal oscillator check failed
>>>>>>> device_attach: rtc0 attach returned 6
>>>>>>> gpio0: <Amlogic aml8726 GPIO> mem 0xc8100024-0xc8100027,0xc8100024-
>> 0xc8100027,0xc8100028-0xc810002b on simplebus0
>>>>>>> gpiobus0: <OFW GPIO bus> on gpio0
>>>>>>> gpioled0: <GPIO led> at pin 13 on gpiobus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpioled0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpiobus0
>>>>>>> gpioc0: <GPIO controller> on gpio0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpioc0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpio0
>>>>>>> gpio1: <Amlogic aml8726 GPIO> mem 0xc1108054-0xc1108057,0xc1108058-
>> 0xc110805b,0xc110805c-0xc110805f on simplebus0
>>>>>>> gpiobus1: <OFW GPIO bus> on gpio1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpiobus1
>>>>>>> gpioc1: <GPIO controller> on gpio1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpioc1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpio1
>>>>>>> gpio2: <Amlogic aml8726 GPIO> mem 0xc110806c-0xc110806f,0xc1108070-
>> 0xc1108073,0xc1108074-0xc1108077 on simplebus0
>>>>>>> gpiobus2: <OFW GPIO bus> on gpio2
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpiobus2
>>>>>>> gpioc2: <GPIO controller> on gpio2
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpioc2
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from gpio2
>>>>>>> aml8726_mmc0: <Amlogic aml8726 MMC> mem 0xc1108c20-0xc1108c3f irq 13 on simplebus0
>>>>>>> mmc0: <MMC/SD bus> on aml8726_mmc0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from mmc0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_mmc0
>>>>>>> aml8726_sdxc0: <Amlogic aml8726-m8 SDXC> mem 0xc1108e00-0xc1108e3b irq 14 on
>> simplebus0
>>>>>>> mmc1: <MMC/SD bus> on aml8726_sdxc0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from mmc1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_sdxc0
>>>>>>> simplebus0: <rng at c1108100> mem 0xc1108100-0xc1108107 compat amlogic,aml8726-rng (no
>> driver attached)
>>>>>>> usbphy0: <Amlogic aml8726-m8 USB PHY> mem 0xc1108800-0xc110881f on simplebus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from usbphy0
>>>>>>> usbphy1: <Amlogic aml8726-m8 USB PHY> mem 0xc1108820-0xc110883f on simplebus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from usbphy1
>>>>>>> dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0xc9040000-0xc907ffff irq 15 on
>> simplebus0
>>>>>>> usbus0 on dwcotg0
>>>>>>> dwcotg0: usbpf: Attached
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from usbus0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from dwcotg0
>>>>>>> dwcotg1: <DWC OTG 2.0 integrated USB controller> mem 0xc90c0000-0xc90fffff irq 16 on
>> simplebus0
>>>>>>> usbus1 on dwcotg1
>>>>>>> dwcotg1: usbpf: Attached
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from usbus1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from dwcotg1
>>>>>>> dwc0: <Amlogic Meson Gigabit Ethernet Controller> mem 0xc9410000-0xc9411fff irq 11
>> on simplebus0
>>>>>>> miibus0: <MII bus> on dwc0
>>>>>>> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0
>>>>>>> rgephy0: OUI 0x00e04c, model 0x0011, rev. 6
>>>>>>> rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX,
>> 1000baseT-FDX-master, auto
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from rgephy0
>>>>>>> rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
>>>>>>> rgephy1: OUI 0x00e04c, model 0x0011, rev. 6
>>>>>>> rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX,
>> 1000baseT-FDX-master, auto
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from rgephy1
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from miibus0
>>>>>>> dwc0: bpf attached
>>>>>>> dwc0: Ethernet address: 62:73:64:5d:6a:ec
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from dwc0
>>>>>>> fb0: <Amlogic aml8726 FB> mem 0xc8006048-0xc8006053,0xc1106800-
>> 0xc1106bff,0xc1107400-0xc11077ff irq 17,18,19,20 on simplebus0
>>>>>>> fbd0 on fb0
>>>>>>> VT: initialize with new VT driver "fb".
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from fbd0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from fb0
>>>>>>> cpulist0: <Open Firmware CPU Group> on ofwbus0
>>>>>>> cpu0: <Open Firmware CPU> on cpulist0
>>>>>>> cpu0: missing 'clock-frequency' property
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from cpu0
>>>>>>> cpu1: <Open Firmware CPU> on cpulist0
>>>>>>> cpu1: missing 'clock-frequency' property
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from cpu1
>>>>>>> cpu2: <Open Firmware CPU> on cpulist0
>>>>>>> cpu2: missing 'clock-frequency' property
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from cpu2
>>>>>>> cpu3: <Open Firmware CPU> on cpulist0
>>>>>>> cpu3: missing 'clock-frequency' property
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from cpu3
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from cpulist0
>>>>>>> ofwbus0: <clk at 0> compat fixed-clock (no driver attached)
>>>>>>> ofwbus0: <leds> compat gpio-leds (no driver attached)
>>>>>>> cryptosoft0: <software crypto>
>>>>>>> crypto: assign cryptosoft0 driver id 0, flags 100663296
>>>>>>> crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
>>>>>>> crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from cryptosoft0
>>>>>>> procfs registered
>>>>>>> Timecounters tick every 10.000 msec
>>>>>>> tcp_init: net.inet.tcp.tcbhashsize auto tuned to 8192
>>>>>>> usbus0: 480Mbps High Speed USB v2.0
>>>>>>> IPsec: Initialized Security Association Processing.
>>>>>>> lo0: bpf attached
>>>>>>> mmc0: Probing bus
>>>>>>> usbus1: 480Mbps High Speed USB v2.0
>>>>>>> mmc0: SD 2.0 interface conditions: OK
>>>>>>> mmc0: SD probe: OK (OCR: 0x40ff8000)
>>>>>>> mmc0: Current OCR: 0x00ff8000
>>>>>>> ugen1.1: <DWCOTG> at usbus1
>>>>>>> uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
>>>>>>> ugen0.1: <DWCOTG> at usbus0
>>>>>>> uhub1: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
>>>>>>> mmc0: Probing cards
>>>>>>> mmc0: New card detected (CID 035344534c3038478029cfee4e00f900)
>>>>>>> mmc0: New card detected (CSD 400e00325b5900003b377f800a404000)
>>>>>>> mmc0: Card at relative address 0xaaaa added:
>>>>>>> mmc0: card: SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD
>>>>>>> mmc0: bus: 4bit, 50MHz, high speed timing
>>>>>>> mmc0: memory: 15523840 blocks, erase sector 8192 blocks
>>>>>>> mmc0: setting transfer rate to 39.750MHz (high speed timing)
>>>>>>> mmcsd0: 8GB <SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD> at mmc0 39.7MHz/4bit/8-
>> block
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from mmcsd0
>>>>>>> mmc1: Probing bus
>>>>>>> GEOM: new disk mmcsd0
>>>>>>> mmc0: setting bus width to 4 bits
>>>>>>> GEOM_PART: partition 1 on (mmcsd0, MBR) is not aligned on 4194304 bytes
>>>>>>> GEOM_PART: partition 2 on (mmcsd0, MBR) is not aligned on 4194304 bytes
>>>>>>> mmc1: SD probe: failed
>>>>>>> mmc1: MMC probe: failed
>>>>>>> mmc1: Current OCR: 0x00000000
>>>>>>> mmc1: No compatible cards found on bus
>>>>>>> Release APs
>>>>>>> WARNING: WITNESS option enabled, expect reduced performance.
>>>>>>> Trying to mount root from ufs:mmcsd0s2 []...
>>>>>>> GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 bytes
>>>>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned on 4194304
>> bytes
>>>>>>> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned on 4194304
>> bytes
>>>>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not aligned on 4194304
>> bytes
>>>>>>> warning: no time-of-day clock registered, system time will not be set accurately
>>>>>>> start_init: trying /sbin/init
>>>>>>> uhub0: 1 port with 1 removable, self powered
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from uhub0
>>>>>>> uhub1: 1 port with 1 removable, self powered
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from uhub1
>>>>>>> ugen1.2: <vendor 0x05e3> at usbus1
>>>>>>> uhub2: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/32.98, addr 2> on usbus1
>>>>>>> uhub2: MTT enabled
>>>>>>> Growing root partition to fill device
>>>>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned on 4194304
>> bytes
>>>>>>> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned on 4194304
>> bytes
>>>>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not aligned on 4194304
>> bytes
>>>>>>> mmcsd0s2 resized
>>>>>>> growfs: superblock not recognized
>>>>>>> /etc/rc: WARNING: hostid: unable to figure out a UUID from DMI data, generating a
>> new one
>>>>>>> uhub2: 4 ports with 4 removable, self powered
>>>>>>> random: harvesting attach, 8 bytes (4 bits) from uhub2
>>>>>>> Setting hostuuid: 214610b1-f72e-11e5-8203-df073412266c.
>>>>>>> Setting hostid: 0x373425ad.
>>>>>>> No suitable dump device was found.
>>>>>>> Starting file system checks:
>>>>>>> /dev/mmcsd0s2: FILE SYSTEM CLEAN; SKIPPING CHECKS
>>>>>>> /dev/mmcsd0s2: clean, 36687 free (103 frags, 4573 blocks, 0.0% fragmentation)
>>>>>>> GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 bytes
>>>>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned on 4194304
>> bytes
>>>>>>> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned on 4194304
>> bytes
>>>>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not aligned on 4194304
>> bytes
>>>>>>> Mounting local file systems:.
>>>>>>> Setting hostname: freebsd.
>>>>>>> Setting up
>> harvesting:[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,C
>> ACHED
>>>>>>> Feeding entropy:random: unblocking device.
>>>>>>> .
>>>>>>> dwc0: link state changed to DOWN
>>>>>>> Starting Network: lo0 dwc0.
>>>>>>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
>>>>>>> options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
>>>>>>> inet6 ::1 prefixlen 128
>>>>>>> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
>>>>>>> inet 127.0.0.1 netmask 0xff000000
>>>>>>> groups: lo
>>>>>>> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
>>>>>>> dwc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
>>>>>>> options=80008<VLAN_MTU,LINKSTATE>
>>>>>>> ether 62:73:64:5d:6a:ec
>>>>>>> media: Ethernet autoselect (none)
>>>>>>> status: no carrier
>>>>>>> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
>>>>>>> ELF ldconfig path: /lib /usr/lib /usr/lib/compat
>>>>>>> Starting devd.
>>>>>>> add net fe80::: gateway ::1
>>>>>>> add net ff02::: gateway ::1
>>>>>>> add net ::ffff:0.0.0.0: gateway ::1
>>>>>>> add net ::0.0.0.0: gateway ::1
>>>>>>> Generating host.conf.
>>>>>>> Waiting 30s for the default route interface: .....(no carrier)
>>>>>>> Creating and/or trimming log files.
>>>>>>> Starting syslogd.
>>>>>>> Clearing /tmp (X related).
>>>>>>> Updating motd:.
>>>>>>> Mounting late file systems:.
>>>>>>> Configuring vt: blanktime.
>>>>>>> Generating RSA host key.
>>>>>>> 2048 SHA256:efid4fCpKZlmdi69b18qj+SNx2mSPQNr6ourB/w9tPw root at freebsd (RSA)
>>>>>>> Generating ECDSA host key.
>>>>>>> 256 SHA256:bpBVM0B9a3xDhmy3bvoC4OuELAJ4fvJd+p3tNwgia6k root at freebsd (ECDSA)
>>>>>>> Generating ED25519 host key.
>>>>>>> 256 SHA256:VHMKoDA1Zv50CmxiLJwTIvg58S2DuBg6zj2VFXDGq/M root at freebsd (ED25519)
>>>>>>> Performing sanity check on sshd configuration.
>>>>>>> Could not load host key: /etc/ssh/ssh_host_dsa_key
>>>>>>> Starting sshd.
>>>>>>> Could not load host key: /etc/ssh/ssh_host_dsa_key
>>>>>>> Starting cron.
>>>>>>> Starting background file system checks in 60 seconds.
>>>>>>> lock order reversal:
>>>>>>> 1st 0xc4499814 ufs (ufs) @ /usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498
>>>>>>> 2nd 0xd90169a0 bufwait (bufwait) @
>> /usr/home/emoe/Projects/ARM/src/sys/ufs/ffs/ffs_vnops.c:263
>>>>>>> 3rd 0xc45c15d4 ufs (ufs) @ /usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498
>>>>>>> stack backtrace:
>>>>>>> mount: /dev/mmcsd0s2: Device busy
>>>>>>>
>>>>>>> Thu Mar 31 10:49:29 UTC 2016
>>>>>>>
>>>>>>> FreeBSD/arm (freebsd) (ttyu0)
>>>>>>>
>>>>>>> login:
>>>>>>>
>>>>>>>> On Mar 30, 2016, at 7:47 PM, Erik Moe <e.moe at rcn.com> wrote:
>>>>>>>>
>>>>>>>> I was able to build a working odroid-c1 image not too long ago. Let me pull the
>> latest sources and see if something has changed.
>>>>>>>>
>>>>>>>> Erik
>>>>>>>>
>>>>>>>>> On Mar 30, 2016, at 2:24 AM, Daniel Braniss <danny at cs.huji.ac.il> wrote:
>>>>>>>>>
>>>>>>>>> Hi,
>>>>>>>>> Managed to make a bootable SD, cross compile world/kernel,
>>>>>>>>> but the kernel startup gets stuck, I can’t even get into the debugger.
>>>>>>>>> any help/hints most welcome :-)
>>>>>>>>> btw, I can also boot via the network, cutting down the debug cycle considerably.
>>>>>>>>> thanks,
>>>>>>>>> danny
>>>>>>>>> PS: here is the console output
>>>>>>>>> <s1>
>>>>>>>>> _______________________________________________
>>>>>>>>> freebsd-arm at freebsd.org mailing list
>>>>>>>>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>>>>>>>>> To unsubscribe, send any mail to "freebsd-arm-unsubscribe at freebsd.org"
>>>>>>>> _______________________________________________
>>>>>>>> freebsd-arm at freebsd.org mailing list
>>>>>>>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>>>>>>>> To unsubscribe, send any mail to "freebsd-arm-unsubscribe at freebsd.org"
>>>>>>>
>>>>>>
>>>>>> _______________________________________________
>>>>>> freebsd-arm at freebsd.org mailing list
>>>>>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>>>>>> To unsubscribe, send any mail to "freebsd-arm-unsubscribe at freebsd.org"
>>>>>
>>>>
>>>
>>
>> _______________________________________________
>> freebsd-arm at freebsd.org mailing list
>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>> To unsubscribe, send any mail to "freebsd-arm-unsubscribe at freebsd.org"
More information about the freebsd-arm
mailing list