SDHC errors during boot on RPi2 (11.0-CURRENT)

Michael Tuexen tuexen at fh-muenster.de
Thu Jul 16 07:33:34 UTC 2015


> On 16 Jul 2015, at 05:17, Warner Losh <imp at bsdimp.com> wrote:
> 
> 
>> On Jul 14, 2015, at 6:06 PM, Dan Raymond <draymond at foxvalley.net> wrote:
>> 
>> Is anyone else getting these errors during every boot?  I'm running r285346.
> 
> I’ve been running on the RPi2 for some time and have never seen this. I haven’t
> rebuild in the past few weeks though.
> 
> Does this happen on either SD cards? Or other versions of the kernel?
I'm observing this for quite a while, reproducible exactly once during
every boot on a RPI2.
Here is the what I see:

> uname -a
FreeBSD rpi2 11.0-CURRENT FreeBSD 11.0-CURRENT #28 r285595M: Wed Jul 15 11:26:48 CEST 2015     tuexen at rpi2:/usr/home/tuexen/head/sys/arm/compile/RPI2  arm
> dmesg
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2015 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #28 r285595M: Wed Jul 15 11:26:48 CEST 2015
    tuexen at rpi2:/usr/home/tuexen/head/sys/arm/compile/RPI2 arm
FreeBSD clang version 3.6.0 (tags/RELEASE_360/final 230434) 20150225
VT: init without driver.
sema_sysinit
CPU: Cortex A7 rev 5 (Cortex-A core)
 Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext
 WB disabled EABT branch prediction enabled
LoUU:2 LoC:3 LoUIS:2 
Cache level 1: 
 32KB/64B 4-way data cache WB Read-Alloc Write-Alloc
 32KB/32B 2-way instruction cache Read-Alloc
Cache level 2: 
 512KB/64B 8-way unified cache WB Read-Alloc Write-Alloc
real memory  = 989851648 (943 MB)
avail memory = 958423040 (914 MB)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> mem 0x3f000000-0x3fffffff on ofwbus0
bcm28360: <Broadcom bcm2836>
generic_timer0: <ARMv7 Generic Timer> irq 72,73,75,74 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality 1000
intc0: <BCM2835 Interrupt Controller> mem 0xb200-0xb3ff on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem 0x10001c-0x100027 on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x200000-0x2000af irq 57,59,58,60 on simplebus0
gpio0: read-only pins: 46,48-53.
gpio0: reserved pins: 48-53.
gpiobus0: <OFW GPIO bus> on gpio0
gpioled0: <GPIO led> at pin(s) 35 on gpiobus0
gpioled1: <GPIO led> at pin(s) 47 on gpiobus0
gpioc0: <GPIO controller> on gpio0
iichb0: <BCM2708/2835 BSC controller> mem 0x205000-0x20501f irq 61 on simplebus0
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <BCM2708/2835 BSC controller> mem 0x804000-0x80401f irq 61 on simplebus0
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
spi0: <BCM2708/2835 SPI controller> mem 0x204000-0x20401f irq 62 on simplebus0
spibus0: <OFW SPI bus> on spi0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7000-0x7fff,0xe05000-0xe05fff irq 24,25,26,27,28,29,30,31,32,33,34,35,36 on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0xb880-0xb8bf irq 1 on simplebus0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x300000-0x3000ff irq 70 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
uart0: <PrimeCell UART (PL011)> mem 0x201000-0x201fff irq 65 on simplebus0
uart0: console (115200,n,8,1)
vchiq0: <BCM2835 VCHIQ> mem 0xb800-0xb84f irq 2 on simplebus0
vchiq0: [GIANT-LOCKED]
vchiq: local ver 6 (min 3), remote ver 6.
pcm0: <VCHQI audio> on vchiq0
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x980000-0x99ffff irq 17 on simplebus0
usbus0 on bcm283x_dwcotg0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
fb0: <BCM2835 VT framebuffer driver> on ofwbus0
fbd0 on fb0
VT: initialize with new VT driver "fb".
fb0: 656x416(656x416 at 0,0) 24bpp
fb0: fbswap: 1, pitch 1968, base 0x3daac000, screen_size 818688
cryptosoft0: <software crypto>
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <DWCOTG> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
sdhci_bcm0-slot0: Got data interrupt 0x00000002, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000040 | Blk cnt:  0x00000001
sdhci_bcm0-slot0: Argument: 0xaaaa0000 | Trn mode: 0x0000071b
sdhci_bcm0-slot0: Present:  0x01ff0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x0000000e | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00fb | Sig enab: 0x01ff00fb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Max curr: 0x00000001
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got data interrupt 0x00000002, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000040 | Blk cnt:  0x00000001
sdhci_bcm0-slot0: Argument: 0xaaaa0000 | Trn mode: 0x0000071b
sdhci_bcm0-slot0: Present:  0x01ff0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x0000000e | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00fb | Sig enab: 0x01ff00fb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Max curr: 0x00000001
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got data interrupt 0x00000002, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000040 | Blk cnt:  0x00000001
sdhci_bcm0-slot0: Argument: 0xaaaa0000 | Trn mode: 0x0000071b
sdhci_bcm0-slot0: Present:  0x01ff0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x0000000e | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00fb | Sig enab: 0x01ff00fb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Max curr: 0x00000001
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got data interrupt 0x00000002, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000040 | Blk cnt:  0x00000001
sdhci_bcm0-slot0: Argument: 0xaaaa0000 | Trn mode: 0x0000071b
sdhci_bcm0-slot0: Present:  0x01ff0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x0000000e | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00fb | Sig enab: 0x01ff00fb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Max curr: 0x00000001
sdhci_bcm0-slot0: ===========================================
uhub0: 1 port with 1 removable, self powered
mmc0: CMD7 failed, RESULT: 1
mmcsd0: 32GB <SDHC SL32G 8.0 SN 03A82991 MFG 12/2014 by 3 SD> at mmc0 41.6MHz/4bit/65535-block
bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM 400MHz, Turbo OFF
Release APs
Root mount waiting for: usbus0
ugen0.2: <vendor 0x0424> at usbus0
uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on usbus0
uhub1: MTT enabled
Root mount waiting for: usbus0
uhub1: 5 ports with 4 removable, self powered
Root mount waiting for: usbus0
ugen0.3: <vendor 0x0424> at usbus0
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0
Trying to mount root from ufs:/dev/mmcsd0s2a [rw,noatime]...
warning: no time-of-day clock registered, system time will not be set accurately
smsc0: chip 0xec00, rev. 0002
miibus0: <MII bus> on smsc0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <USB Ethernet> on smsc0
ue0: Ethernet address: b8:27:eb:81:ba:40
random: unblocking device.
smsc0: chip 0xec00, rev. 0002
ue0: link state changed to DOWN
ue0: link state changed to UP
> 

Best regards
Michael
> 
> Warner
> 



More information about the freebsd-arm mailing list