compaq 6515b turion x2 laptop
R. Riehle
rar102 at ra.msstate.edu
Thu May 15 04:57:01 UTC 2008
Coleman,
This laptop has a flaky connector to the cdrom. It took me a lot of time
and pulled-out hair to determine this. It needs to go back to HP before I
can help you on this front.
Coleman Kane-4 wrote:
>
> On Mon, 2008-05-12 at 13:51 -0500, Robertsen A. Riehle wrote:
>> Coleman,
>>
>> Sorry for dropping off the Earth for a moment there. In order to make
>> amends,
>> I am giving you two dmesg's. One from the installed NetBSD and one from
>> the
>> FreeBSD livefs. Tell me if there is anything else I can get for you. I
>> don't know if this is helpful or not. Possibly helpful command line
>> output
>> below:
>>
>> dmesg | grep pcm
>> No output. This is not suprising for a livefs.
>>
>> kldload snd_hda
>> kldload: can't load snd_hda: No such file or directory. Not
>> surprising,
>> again. But it was worth a try.
>>
>> dmesg | grep atapci
>> atapci0: <ATI ATA controller> port
>> 0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f mem
>> 0xd0609000-0xd06093ff irq 16 at device 18.0 on pci0
>> atapci0: [ITHREAD]
>> ata2: <ATA channel 0> on atapci0
>> ata3: <ATA channel 1> on atapci0
>> atapci1: <ATI IXP600 UDMA133 controller> port
>> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x5040-0x504f irq 16 at device 20.1
>> on
>> pci0
>> ata0: <ATA channel 0> on atapci1
>>
>
> It looks to me that you have almost the identical system to what I have
> from HP. The SATA controller is definitely the same exact memory
> mapping. So, I've got two projects for you:
>
> 1) See if you can boot off the LiveFS again, and give me the output of
> "devinfo -u -v"
> 2) Visit the following page:
> http://www.cokane.org/dokuwiki/freebsd/amd64_compatibility#getting_the_hp_compaq_6715b_working
>
> Follow the directions that point you to where to find the good ISO
> images, and
> use them to boot the system. When you get to the boot menu, choose
> option #6
> that will take you to the loader console. Then enter the following at
> the
> loader prompt:
>
> set hw.pci.hp6715b_membase_for_hda_audio="0xd0614000"
>
> Then enter (to start the system):
>
> boot
>
> See if that does anything for you better. If you still have problems,
> then it is likely you'll need a different membase. I hopefully will be
> able to give you a good mem-base depending upon the output of #1, above.
>
> The purpose of setting that loader variable is discussed further down
> the document on my site, under the HDA Audio device discussion. You can
> safely add that loader setting to /boot/loader.conf so that it is
> automatically set after you get your system installed.
>
> I'd like to get a copy of your new dmesg (using my images) after you
> boot up as well.
>
> --
> Coleman Kane
>
>
> Rest of the blob copied below:
>> ##################################################################
>> Here is the FreeBSD dmesg:
>> Copyright (c) 1992-2008 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>> The Regents of the University of California. All rights reserved.
>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>> FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008
>> root at driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
>> Timecounter "i8254" frequency 1193182 Hz quality 0
>> CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-64 (2194.58-MHz K8-class
>> CPU)
>> Origin = "AuthenticAMD" Id = 0x60f82 Stepping = 2
>>
>> Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
>> Features2=0x2001<SSE3,CX16>
>> AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
>> AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch>
>> Cores per package: 2
>> usable memory = 4143468544 (3951 MB)
>> avail memory = 3974230016 (3790 MB)
>> ACPI APIC Table: <HP 0944 >
>> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
>> cpu0 (BSP): APIC ID: 0
>> cpu1 (AP): APIC ID: 1
>> ACPI Error (tbfadt-0516): 32/64X address mismatch in "Pm2ControlBlock": [
>> 8800] [ 0 8100], using 64X [20070320]
>> ioapic0: Changing APIC ID to 2
>> ioapic0 <Version 2.1> irqs 0-23 on motherboard
>> kbd1 at kbdmux0
>> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
>> RF5413)
>> hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 10:34:18)
>> acpi0: <HPQOEM SLIC-MPC> on motherboard
>> acpi0: [ITHREAD]
>> acpi0: Power Button (fixed)
>> unknown: I/O range not supported
>> acpi0: reservation of 0, 8000000 (3) failed
>> acpi0: reservation of 100000, fff00000 (3) failed
>> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
>> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
>> acpi_ec0: <Embedded Controller: GPE 0x11> port 0x62,0x66 on acpi0
>> cpu0: <ACPI CPU> on acpi0
>> acpi_throttle0: <ACPI CPU Throttling> on cpu0
>> powernow0: <PowerNow! K8> on cpu0
>> cpu1: <ACPI CPU> on acpi0
>> acpi_throttle1: <ACPI CPU Throttling> on cpu1
>> acpi_throttle1: failed to attach P_CNT
>> device_attach: acpi_throttle1 attach returned 6
>> powernow1: <PowerNow! K8> on cpu1
>> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
>> pci0: <ACPI PCI bus> on pcib0
>> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
>> pci1: <ACPI PCI bus> on pcib1
>> vgapci0: <VGA-compatible display> port 0x4000-0x40ff mem
>> 0xc0000000-0xc7ffffff,0xd0400000-0xd040ffff,0xd0500000-0xd05fffff irq 19
>> at
>> device 5.0 on pci1
>> pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
>> pci16: <ACPI PCI bus> on pcib2
>> pci0:16:0:0: failed to read VPD data.
>> bge0: <Broadcom BCM5754/5787 A2, ASIC rev. 0xb002> mem
>> 0xd0000000-0xd000ffff
>> irq 16 at device 0.0 on pci16
>> miibus0: <MII bus> on bge0
>> brgphy0: <BCM5787 10/100/1000baseTX PHY> PHY 1 on miibus0
>> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
>> 1000baseT-FDX, auto
>> bge0: Ethernet address: 00:1f:29:85:3d:63
>> bge0: [ITHREAD]
>> pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
>> pci32: <ACPI PCI bus> on pcib3
>> pcib4: <ACPI PCI-PCI bridge> at device 6.0 on pci0
>> pci48: <ACPI PCI bus> on pcib4
>> pci48: <network> at device 0.0 (no driver attached)
>> atapci0: <ATI ATA controller> port
>> 0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f mem
>> 0xd0609000-0xd06093ff irq 16 at device 18.0 on pci0
>> atapci0: [ITHREAD]
>> ata2: <ATA channel 0> on atapci0
>> ata2: [ITHREAD]
>> ata3: <ATA channel 1> on atapci0
>> ata3: [ITHREAD]
>> ohci0: <OHCI (generic) USB controller> mem 0xd0601000-0xd0601fff irq 23
>> at
>> device 19.0 on pci0
>> ohci0: [GIANT-LOCKED]
>> ohci0: [ITHREAD]
>> usb0: OHCI version 1.0, legacy support
>> usb0: <OHCI (generic) USB controller> on ohci0
>> usb0: USB revision 1.0
>> uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
>> uhub0: 2 ports with 2 removable, self powered
>> ohci1: <OHCI (generic) USB controller> mem 0xd0602000-0xd0602fff irq 17
>> at
>> device 19.1 on pci0
>> ohci1: [GIANT-LOCKED]
>> ohci1: [ITHREAD]
>> usb1: OHCI version 1.0, legacy support
>> usb1: <OHCI (generic) USB controller> on ohci1
>> usb1: USB revision 1.0
>> uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
>> uhub1: 2 ports with 2 removable, self powered
>> ohci2: <OHCI (generic) USB controller> mem 0xd0603000-0xd0603fff irq 17
>> at
>> device 19.2 on pci0
>> ohci2: [GIANT-LOCKED]
>> ohci2: [ITHREAD]
>> usb2: OHCI version 1.0, legacy support
>> usb2: <OHCI (generic) USB controller> on ohci2
>> usb2: USB revision 1.0
>> uhub2: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
>> uhub2: 2 ports with 2 removable, self powered
>> ohci3: <OHCI (generic) USB controller> mem 0xd0604000-0xd0604fff irq 17
>> at
>> device 19.3 on pci0
>> ohci3: [GIANT-LOCKED]
>> ohci3: [ITHREAD]
>> usb3: OHCI version 1.0, legacy support
>> usb3: <OHCI (generic) USB controller> on ohci3
>> usb3: USB revision 1.0
>> uhub3: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
>> uhub3: 2 ports with 2 removable, self powered
>> ohci4: <OHCI (generic) USB controller> mem 0xd0605000-0xd0605fff irq 17
>> at
>> device 19.4 on pci0
>> ohci4: [GIANT-LOCKED]
>> ohci4: [ITHREAD]
>> usb4: OHCI version 1.0, legacy support
>> usb4: <OHCI (generic) USB controller> on ohci4
>> usb4: USB revision 1.0
>> uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
>> uhub4: 2 ports with 2 removable, self powered
>> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd0606000-0xd06060ff irq
>> 23 at
>> device 19.5 on pci0
>> ehci0: [GIANT-LOCKED]
>> ehci0: [ITHREAD]
>> usb5: EHCI version 1.0
>> usb5: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4
>> usb5: <EHCI (generic) USB 2.0 controller> on ehci0
>> usb5: USB revision 2.0
>> uhub5: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5
>> uhub5: 10 ports with 10 removable, self powered
>> pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
>> atapci1: <ATI IXP600 UDMA133 controller> port
>> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x5040-0x504f irq 16 at device 20.1
>> on
>> pci0
>> ata0: <ATA channel 0> on atapci1
>> ata0: [ITHREAD]
>> pci0: <multimedia> at device 20.2 (no driver attached)
>> isab0: <PCI-ISA bridge> at device 20.3 on pci0
>> isa0: <ISA bus> on isab0
>> pcib5: <ACPI PCI-PCI bridge> at device 20.4 on pci0
>> pci2: <ACPI PCI bus> on pcib5
>> cbb0: <RF5C476 PCI-CardBus Bridge> mem 0xd0100000-0xd0100fff irq 20 at
>> device
>> 4.0 on pci2
>> cardbus0: <CardBus bus> on cbb0
>> pccard0: <16-bit PCCard bus> on cbb0
>> cbb0: [ITHREAD]
>> fwohci0: <1394 Open Host Controller Interface> mem 0xd0101000-0xd01017ff
>> irq
>> 21 at device 4.1 on pci2
>> fwohci0: [FILTER]
>> fwohci0: OHCI version 1.10 (ROM=0)
>> fwohci0: No. of Isochronous channels is 4.
>> fwohci0: EUI64 00:02:3f:99:29:21:1d:10
>> fwohci0: Phy 1394a available S400, 1 ports.
>> fwohci0: Link S400, max_rec 2048 bytes.
>> firewire0: <IEEE1394(FireWire) bus> on fwohci0
>> dcons_crom0: <dcons configuration ROM> on firewire0
>> dcons_crom0: bus_addr 0x15dc000
>> fwe0: <Ethernet over FireWire> on firewire0
>> if_fwe0: Fake Ethernet address: 02:02:3f:21:1d:10
>> fwe0: Ethernet address: 02:02:3f:21:1d:10
>> fwip0: <IP over FireWire> on firewire0
>> fwip0: Firewire address: 00:02:3f:99:29:21:1d:10 @ 0xfffe00000000, S400,
>> maxrec 2048
>> sbp0: <SBP-2/SCSI over FireWire> on firewire0
>> fwohci0: Initiate bus reset
>> fwohci0: BUS reset
>> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
>> battery0: <ACPI Control Method Battery> on acpi0
>> battery1: <ACPI Control Method Battery> on acpi0
>> acpi_acad0: <AC Adapter> on acpi0
>> acpi_button0: <Sleep Button> on acpi0
>> acpi_lid0: <Control Method Lid Switch> on acpi0
>> acpi_tz0: <Thermal Zone> on acpi0
>> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
>> atkbd0: <AT Keyboard> irq 1 on atkbdc0
>> kbd0 at atkbd0
>> atkbd0: [GIANT-LOCKED]
>> atkbd0: [ITHREAD]
>> psm0: <PS/2 Mouse> irq 12 on atkbdc0
>> psm0: [GIANT-LOCKED]
>> psm0: [ITHREAD]
>> psm0: model IntelliMouse, device ID 3
>> ppc0: <Parallel port> port 0-0x7,0x400-0x402 on acpi0
>> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
>> ppbus0: <Parallel port bus> on ppc0
>> plip0: <PLIP network interface> on ppbus0
>> lpt0: <Printer> on ppbus0
>> lpt0: Polled port
>> ppi0: <Parallel I/O> on ppbus0
>> orm0: <ISA Option ROM> at iomem 0xd0000-0xd0fff on isa0
>> sc0: <System console> at flags 0x100 on isa0
>> sc0: VGA <16 virtual consoles, flags=0x300>
>> sio0: configured irq 4 not in bitmap of probed irqs 0
>> sio0: port may not be enabled
>> sio0: configured irq 4 not in bitmap of probed irqs 0
>> sio0: port may not be enabled
>> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
>> sio0: type 8250 or not responding
>> sio0: [FILTER]
>> sio1: configured irq 3 not in bitmap of probed irqs 0
>> sio1: port may not be enabled
>> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
>> ugen0: <Broadcom Corp HP Integrated Module, class 224/1, rev 2.00/1.00,
>> addr
>> 2> on uhub0
>> umass0: <CRUCIAL USB DRIVE, class 0/0, rev 1.10/0.01, addr 2> on uhub1
>> ugen1: <vendor 0x08ff Fingerprint Sensor, class 255/255, rev 1.10/6.23,
>> addr
>> 2> on uhub2
>> Timecounters tick every 1.000 msec
>> hptrr: no controller detected.
>> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
>> firewire0: bus manager 0 (me)
>> md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xffffffff80bc6c08
>> acd0: DVDR <HL-DT-ST DVDRAM GSA-T20L/NC08> at ata0-master PIO4
>> ad4: 114473MB <Seagate ST9120822AS 3.BHE> at ata2-master UDMA33
>> acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00
>> GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD_LiveFS.
>> acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00
>> GEOM_LABEL: Label for provider ad4s3 is ntfs/HP_RECOVERY.
>> GEOM_LABEL: Label for provider ad4s4 is ntfs/OS_TOOLS.
>> SMP: AP CPU #1 Launched!
>> da0 at umass-sim0 bus 0 target 0 lun 0
>> da0: <CRUCIAL USB DRIVE 1.12> Removable Direct Access SCSI-CCS device
>> da0: 1.000MB/s transfers
>> da0: 61MB (125952 512 byte sectors: 64H 32S/T 61C)
>> GEOM_LABEL: Label for provider da0s1 is msdosfs/CRUCIAL.
>> Trying to mount root from ufs:/dev/md0
>> GEOM_LABEL: Label msdosfs/CRUCIAL removed.
>> GEOM_LABEL: Label for provider da0s1 is msdosfs/CRUCIAL.
>> GEOM_LABEL: Label msdosfs/CRUCIAL removed.
>>
>> #######################################################################
>> Here is the NetBSD dmesg:
>>
>> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
>> 2006, 2007
>> The NetBSD Foundation, Inc. All rights reserved.
>> Copyright (c) 1982, 1986, 1989, 1991, 1993
>> The Regents of the University of California. All rights reserved.
>>
>> NetBSD 4.0 (GENERIC) #0: Sat Dec 15 22:25:31 PST 2007
>>
>> builds at wb28:/home/builds/ab/netbsd-4-0-RELEASE/amd64/200712160005Z-obj/home/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/amd64/compile/GENERIC
>> total memory = 3967 MB
>> avail memory = 3815 MB
>> timecounter: Timecounters tick every 10.000 msec
>> timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
>> mainbus0 (root)
>> cpu0 at mainbus0: apid 0 (boot processor)
>> cpu0: AMD Turion(tm) 64 X2 Mobile Technology TL-64, 2195.04 MHz
>> cpu0: features:
>> ffdbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
>> cpu0: features: ffdbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,MMXX,MMX>
>> cpu0: features: ffdbfbff<FXSR,SSE,SSE2,B27,HTT,LONG,3DNOW2,3DNOW>
>> cpu0: features2: 2001<SSE3>
>> cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
>> cpu0: L2 cache 512 KB 64B/line 16-way
>> cpu0: ITLB 32 4 KB entries fully associative, 8 4 MB entries fully
>> associative
>> cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries fully
>> associative
>> cpu0: AMD Power Management features: 7f<STC,TM,TTP,VID,FID,TS>
>> cpu0: AMD PowerNow! Technology 2200 MHz
>> cpu0: available frequencies (Mhz): 800 1600 1800 2000 2200
>> cpu0: calibrating local timer
>> cpu0: apic clock running at 199 MHz
>> cpu0: 8 page colors
>> cpu1 at mainbus0: apid 1 (application processor)
>> cpu1: not started
>> ioapic0 at mainbus0 apid 2 (I/O APIC)
>> ioapic0: pa 0xfec00000, version 21, 24 pins
>> ioapic0: misconfigured as apic 0
>> ioapic0: remapped to apic 2
>> acpi0 at mainbus0: Advanced Configuration and Power Interface
>> acpi0: using Intel ACPI CA subsystem version 20060217
>> acpi0: X/RSDT: OemId <HPQOEM,SLIC-MPC,00000001>, AslId <HP ,00000001>
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A1 (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C28C (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A2 (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A3 (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C253 (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A4 (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A5 (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> ACPI Error (evgpeblk-0394): Unknown GPE method type: C262 (name not of
>> form
>> _Lxx or _Exx) [20060217]
>> acpi0: SCI interrupting at int 9
>> acpi0: fixed-feature power button present
>> timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
>> ACPI-Fast 32-bit timer
>> mpacpi: could not get bus number, assuming bus 0
>> ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
>> ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
>> PNP0C01 [System Board] at acpi0 not configured
>> PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
>> acpiec0: io 0x62,0x66
>> PNP0A06 [Generic Container Device] at acpi0 not configured
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> IFX0102 at acpi0 not configured
>> PNP0C04 [Math Coprocessor] at acpi0 not configured
>> attimer1 at acpi0 (PNP0100): AT Timer
>> attimer1: io 0x40-0x43 irq 0
>> PNP0200 [AT DMA Controller] at acpi0 not configured
>> pcppi1 at acpi0 (PNP0800)
>> pcppi1: io 0x61
>> pcppi1: children must have an explicit unit
>> midi0 at pcppi1: PC speaker (CPU-intensive output)
>> sysbeep0 at pcppi1
>> PNP0B00 [AT Real-Time Clock] at acpi0 not configured
>> pckbc1 at acpi0 (PNP0303): kbd port
>> pckbc1: io 0x60,0x64 irq 1
>> pckbc2 at acpi0 (SYN0131): aux port
>> pckbc2: irq 12
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> PNP0000 [AT Interrupt Controller] at acpi0 not configured
>> PNP0C02 [Plug and Play motherboard register resources] at acpi0 not
>> configured
>> HPQ0004 at acpi0 not configured
>> PNP0C02 [Plug and Play motherboard register resources] at acpi0 not
>> configured
>> HPQ0006 at acpi0 not configured
>> acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
>> acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
>> acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
>> acpibut0 at acpi0 (PNP0C0E): ACPI Sleep Button
>> acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
>> PNP0C14 at acpi0 not configured
>> PNP0C02 [Plug and Play motherboard register resources] at acpi0 not
>> configured
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
>> PNP0C0B [ACPI Fan] at acpi0 not configured
>> PNP0C0B [ACPI Fan] at acpi0 not configured
>> PNP0C0B [ACPI Fan] at acpi0 not configured
>> PNP0C0B [ACPI Fan] at acpi0 not configured
>> acpitz0 at acpi0: ACPI Thermal Zone
>> acpitz0: unable to get polling interval; using default of 30.0s
>> acpitz0: active cooling level 0: 70.0C
>> acpitz0: active cooling level 1: 60.0C
>> acpitz0: active cooling level 2: 50.0C
>> acpitz0: active cooling level 3: 40.0C
>> acpitz0: critical 105.0C passive 38.0C
>> pcppi1: attached to attimer1
>> pckbd0 at pckbc1 (kbd slot)
>> pckbc1: using irq 1 for kbd slot
>> wskbd0 at pckbd0: console keyboard
>> pms0 at pckbc1 (aux slot)
>> pms0: Synaptics touchpad version 6.2
>> pms0: Palm detect, Multi-finger
>> pckbc1: using irq 12 for aux slot
>> wsmouse0 at pms0 mux 0
>> pci0 at mainbus0 bus 0: configuration mode 1
>> pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
>> pchb0 at pci0 dev 0 function 0
>> pchb0: ATI Technologies product 0x7910 (rev. 0x00)
>> ppb0 at pci0 dev 1 function 0: ATI Technologies product 0x7912 (rev.
>> 0x00)
>> pci1 at ppb0 bus 1
>> pci1: i/o space, memory space enabled
>> vga0 at pci1 dev 5 function 0: ATI Technologies product 0x791f (rev.
>> 0x00)
>> wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using
>> wskbd0
>> wsmux1: connecting to wsdisplay0
>> ppb1 at pci0 dev 4 function 0: ATI Technologies product 0x7914 (rev.
>> 0x00)
>> pci2 at ppb1 bus 16
>> pci2: i/o space, memory space enabled, rd/line, wr/inv ok
>> bge0 at pci2 dev 0 function 0: Broadcom BCM5787M Gigabit Ethernet
>> bge0: interrupting at ioapic0 pin 16 (irq 10)
>> bge0: ASIC BCM5754/5787 A2 (0xb002), Ethernet address 00:1f:29:85:3d:63
>> bge0: setting short Tx thresholds
>> brgphy0 at bge0 phy 1: BCM5754/5787 1000BASE-T media interface, rev. 0
>> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
>> 1000baseT-FDX, auto
>> ppb2 at pci0 dev 5 function 0: ATI Technologies product 0x7915 (rev.
>> 0x00)
>> pci3 at ppb2 bus 32
>> pci3: i/o space, memory space enabled, rd/line, wr/inv ok
>> ppb3 at pci0 dev 6 function 0: ATI Technologies product 0x7916 (rev.
>> 0x00)
>> pci4 at ppb3 bus 48
>> pci4: i/o space, memory space enabled, rd/line, wr/inv ok
>> Broadcom BCM4312 (miscellaneous network, revision 0x02) at pci4 dev 0
>> function
>> 0 not configured
>> ixpide0 at pci0 dev 18 function 0
>> ixpide0: ATI Technologies IXP IDE Controller (rev. 0x00)
>> ixpide0: bus-master DMA support present
>> ixpide0: primary channel configured to native-PCI mode
>> ixpide0: using ioapic0 pin 16 (irq 10) for native-PCI interrupt
>> atabus0 at ixpide0 channel 0
>> ixpide0: secondary channel configured to native-PCI mode
>> atabus1 at ixpide0 channel 1
>> ohci0 at pci0 dev 19 function 0: ATI Technologies product 0x4387 (rev.
>> 0x00)
>> ohci0: interrupting at ioapic0 pin 23 (irq 11)
>> ohci0: OHCI version 1.0, legacy support
>> usb0 at ohci0: USB revision 1.0
>> uhub0 at usb0
>> uhub0: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>> uhub0: 2 ports with 2 removable, self powered
>> ohci1 at pci0 dev 19 function 1: ATI Technologies product 0x4388 (rev.
>> 0x00)
>> ohci1: interrupting at ioapic0 pin 17 (irq 5)
>> ohci1: OHCI version 1.0, legacy support
>> usb1 at ohci1: USB revision 1.0
>> uhub1 at usb1
>> uhub1: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>> uhub1: 2 ports with 2 removable, self powered
>> ohci2 at pci0 dev 19 function 2: ATI Technologies product 0x4389 (rev.
>> 0x00)
>> ohci2: interrupting at ioapic0 pin 17 (irq 5)
>> ohci2: OHCI version 1.0, legacy support
>> usb2 at ohci2: USB revision 1.0
>> uhub2 at usb2
>> uhub2: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>> uhub2: 2 ports with 2 removable, self powered
>> ohci3 at pci0 dev 19 function 3: ATI Technologies product 0x438a (rev.
>> 0x00)
>> ohci3: interrupting at ioapic0 pin 17 (irq 5)
>> ohci3: OHCI version 1.0, legacy support
>> usb3 at ohci3: USB revision 1.0
>> uhub3 at usb3
>> uhub3: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>> uhub3: 2 ports with 2 removable, self powered
>> ohci4 at pci0 dev 19 function 4: ATI Technologies product 0x438b (rev.
>> 0x00)
>> ohci4: interrupting at ioapic0 pin 17 (irq 5)
>> ohci4: OHCI version 1.0, legacy support
>> usb4 at ohci4: USB revision 1.0
>> uhub4 at usb4
>> uhub4: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>> uhub4: 2 ports with 2 removable, self powered
>> ehci0 at pci0 dev 19 function 5: ATI Technologies product 0x4386 (rev.
>> 0x00)
>> ehci0: interrupting at ioapic0 pin 23 (irq 11)
>> ehci0: BIOS has given up ownership
>> ehci0: EHCI version 1.0
>> ehci0: companion controllers, 2 ports each: ohci0 ohci1 ohci2 ohci3 ohci4
>> usb5 at ehci0: USB revision 2.0
>> uhub5 at usb5
>> uhub5: ATI Technologies EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
>> uhub5: 10 ports with 10 removable, self powered
>> ATI Technologies product 0x4385 (SMBus serial bus, revision 0x14) at pci0
>> dev
>> 20 function 0 not configured
>> ixpide1 at pci0 dev 20 function 1
>> ixpide1: ATI Technologies IXP IDE Controller (rev. 0x00)
>> ixpide1: bus-master DMA support present
>> ixpide1: primary channel configured to compatibility mode
>> ixpide1: primary channel interrupting at ioapic0 pin 14 (irq 14)
>> atabus2 at ixpide1 channel 0
>> ixpide1: secondary channel wired to compatibility mode
>> ixpide1: secondary channel interrupting at ioapic0 pin 15 (irq 15)
>> atabus3 at ixpide1 channel 1
>> azalia0 at pci0 dev 20 function 2: Generic High Definition Audio
>> Controller
>> azalia0: interrupting at ioapic0 pin 16 (irq 10)
>> azalia0: host: 0x1002/0x4383 (rev. 0)
>> azalia0: host: High Definition Audio rev. 1.0
>> pcib0 at pci0 dev 20 function 3
>> pcib0: ATI Technologies product 0x438d (rev. 0x00)
>> ppb4 at pci0 dev 20 function 4: ATI Technologies product 0x4384 (rev.
>> 0x00)
>> pci5 at ppb4 bus 2
>> pci5: i/o space, memory space enabled
>> cbb0 at pci5 dev 4 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 0xb6)
>> fwohci0 at pci5 dev 4 function 1: Ricoh product 0x0832 (rev. 0x02)
>> fwohci0: interrupting at ioapic0 pin 21 (irq 5)
>> fwohci0: OHCI version 1.10 (ROM=0)
>> fwohci0: No. of Isochronous channels is 4.
>> fwohci0: EUI64 00:02:3f:99:29:21:1d:10
>> fwohci0: Phy 1394a available S400, 1 ports.
>> fwohci0: Link S400, max_rec 2048 bytes.
>> ieee1394if0 at fwohci0: IEEE1394 bus
>> fwip0 at ieee1394if0: IP over IEEE1394
>> fwohci0: Initiate bus reset
>> cbb0: interrupting at ioapic0 pin 20 (irq 10)
>> cardslot0 at cbb0 slot 0 flags 0
>> cardbus0 at cardslot0: bus 3
>> pcmcia0 at cardslot0
>> pchb1 at pci0 dev 24 function 0
>> pchb1: Advanced Micro Devices AMD64 HyperTransport configuration (rev.
>> 0x00)
>> pchb2 at pci0 dev 24 function 1
>> pchb2: Advanced Micro Devices AMD64 Address Map configuration (rev. 0x00)
>> pchb3 at pci0 dev 24 function 2
>> pchb3: Advanced Micro Devices AMD64 DRAM configuration (rev. 0x00)
>> pchb4 at pci0 dev 24 function 3
>> pchb4: Advanced Micro Devices AMD64 Miscellaneous configuration (rev.
>> 0x00)
>> isa0 at pcib0
>> ioapic0: enabling
>> WARNING: Callback scheduled before sysmon task queue thread present.
>> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
>> ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
>> ieee1394if0: bus manager 0 (me)
>> timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
>> azalia0: codec[0]: Analog Devices AD1981HD (rev. 2.0)
>> azalia0: codec[0]: High Definition Audio rev. 1.0
>> azalia0: playback: max channels=2, encodings=1<PCM>
>> azalia0: playback: PCM
>> formats=e007f<24bit,20bit,16bit,48kHz,44.1kHz,32kHz,22.05kHz,16kHz,11.025kHz,8kHz>
>> azalia0: recording: max channels=2, encodings=1<PCM>
>> azalia0: recording: PCM
>> formats=6007f<20bit,16bit,48kHz,44.1kHz,32kHz,22.05kHz,16kHz,11.025kHz,8kHz>
>> azalia0: codec[1]: 0x11c1/0x1040 (rev. 2.0)
>> azalia0: codec[1]: High Definition Audio rev. 1.0
>> azalia0: codec[1]: No support for modem function groups
>> azalia0: codec[1] has no audio function groups
>> audio0 at azalia0: full duplex, independent
>> Kernelized RAIDframe activated
>> acpibat0: battery info: Hewlett-Packard, LIon, Primary, 48204 2008/04/13
>> ugen0 at uhub2 port 1
>> ugen0: AuthenTec Fingerprint Sensor, rev 1.10/6.23, addr 2
>> wd0 at atabus0 drive 0: <ST9120822AS>
>> wd0: drive supports 16-sector PIO transfers, LBA48 addressing
>> wd0: 111 GB, 232581 cyl, 16 head, 63 sec, 512 bytes/sect x 234441648
>> sectors
>> wd0: 32-bit data port
>> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
>> wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using
>> DMA)
>> atapibus0 at atabus2: 2 targets
>> cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GSA-T20L, KZ183LD5612, NC08>
>> cdrom
>> removable
>> cd0: 32-bit data port
>> cd0: drive supports PIO mode 4, DMA mode 2
>> cd0(ixpide1:0:0): using PIO mode 4, DMA mode 2 (using DMA)
>> boot device: wd0
>> root on wd0a dumps on wd0b
>> root file system type: ffs
>> WARNING: clock gained 7 days
>> WARNING: CHECK AND RESET THE DATE!
>> wsdisplay0: screen 1 added (80x25, vt100 emulation)
>> wsdisplay0: screen 2 added (80x25, vt100 emulation)
>> wsdisplay0: screen 3 added (80x25, vt100 emulation)
>> wsdisplay0: screen 4 added (80x25, vt100 emulation)
>>
>>
>>
>>
>>
>>
>> On Sunday 11 May 2008 07:49:47 you wrote:
>> > On Sat, 2008-05-10 at 14:33 -0400, Coleman Kane wrote:
>> > > On Sat, 2008-05-10 at 12:13 -0500, rar102 at ra.msstate.edu wrote:
>> > > > Quoting Coleman Kane <cokane at freebsd.org>:
>> > > >
>> > > > Yes!!! thank you. Unfortunately, I don't have access to another
>> amd64
>> > > > box to try your patch. Sorry. But, I will look at the dmesg and
>> send
>> > > > it to you.
>> > >
>> > > Excellent. A dmesg will be very helpful for me to write a patch from,
>> as
>> > > it will allow me to see if it is or is not the sound driver
>> overlapping
>> > > memory in your case. I suspect that the BIOS images are so similar
>> that
>> > > you probably even have almost the same bios-chosen memory regions on
>> > > your system.
>> >
>> > If you're having difficulty getting a dmesg, you might want to try
>> > booting off the LiveFS disc with a USB flash drive plugged in. You can
>> > then mount the flash drive (which should be detected as SCSI) and write
>> > the dmesg output there.
>> >
>> > > > > RAR,
>> > > > >
>> > > > > You are in luck! Well, actually I have good news and I have bad
>> news.
>> > > > > The good news is that I have nearly the same (6715b) laptop and
>> > > > > experienced similar problems when getting FreeBSD onto it. After
>> some
>> > > > > work, I've been able to use FreeBSD reliably on the system.
>> > > > >
>> > > > > The bad news is that you probably have an overlap of PCI memory
>> > > > > ranges between the SATA controller and another device in the
>> system
>> > > > > (likely the audio controller).
>> > > > >
>> > > > > I put up a page describing the problem here:
>> > > >
>> > > >
>> http://www.cokane.org/dokuwiki/freebsd/amd64_compatibility#getting_the_
>> > > >hp_compaq_6715b_working
>> > > >
>> > > > > Specifically, read this section:
>> > > >
>> > > >
>> http://www.cokane.org/dokuwiki/freebsd/amd64_compatibility#the_onboard_
>> > > >ati_sb600_hda_audio_controller
>> > > >
>> > > > > Give me the weekend, and I will post a 7.0-RELEASE CD with the
>> patch
>> > > > > in it. I figured that I should have done it a while ago. Oh well.
>> > > > >
>> > > > > While you are at it, see if you can use Scroll-Lock and the
>> up/down
>> > > > > keys to read the kernel messages. See if you can find the atapci0
>> > > > > probe line for your SATA controller (AHCI), as well as the line
>> for
>> > > > > your pcm0 device and send them back to me. I can add your info to
>> my
>> > > > > webpage to help others.
>> > > > >
>> > > > > It will look like this:
>> > > > > atapci0: <ATI IXP600 SATA300 controller> port
>> > > > >
>> 0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f
>> > > > > mem 0xd0609000-0xd06093ff irq 16 at device 18.0 on pci0
>> > > > > ...
>> > > > > pcm0: <ATI SB600 High Definition Audio Controller> mem
>> > > > > 0xd0608000-0xd060bfff irq 16 at device 20.2 on pci0
>> > > > >
>> > > > > You'll notice the "mem" resource for the audio controller is
>> > > > > 0xd0608000-0xd060bff, and the "mem" resource for the SATA
>> controller
>> > > > > is 0xd0609000-0xd06093ff. The SATA controller's "mem" resource is
>> > > > > completely covered by this audio controller.
>> > > > >
>> > > > > If you happen to have access to another machine for building your
>> own
>> > > > > releases, you can try my patch and build them from it.
>> > > > >
>> > > > > --
>> > > > > Coleman Kane
>
>
>
>
--
View this message in context: http://www.nabble.com/compaq-6515b-turion-x2-laptop-tp17165100p17245805.html
Sent from the freebsd-arch mailing list archive at Nabble.com.
More information about the freebsd-arch
mailing list