compaq 6515b turion x2 laptop

Robertsen A. Riehle rar102 at ra.msstate.edu
Mon May 12 18:52:09 UTC 2008 

Coleman,

Sorry for dropping off the Earth for a moment there.  In order to make amends, 
I am giving you two dmesg's.  One from the installed NetBSD and one from the 
FreeBSD livefs.  Tell me if there is anything else I can get for you.  I 
don't know if this is helpful or not.  Possibly helpful command line output 
below:

dmesg | grep pcm 
No output.  This is not suprising for a livefs.

kldload snd_hda
kldload:  can't load snd_hda:  No such file or directory.  Not surprising, 
again.  But it was worth a try.

dmesg | grep atapci
atapci0: <ATI ATA controller> port
0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f mem 
0xd0609000-0xd06093ff irq 16 at device 18.0 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
atapci1: <ATI IXP600 UDMA133 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x5040-0x504f irq 16 at device 20.1 on 
pci0
ata0: <ATA channel 0> on atapci1

##################################################################
Here is the FreeBSD dmesg:
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008
    root at driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-64 (2194.58-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x60f82  Stepping = 2
  
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x2001<SSE3,CX16>
  AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch>
  Cores per package: 2
usable memory = 4143468544 (3951 MB)
avail memory  = 3974230016 (3790 MB)
ACPI APIC Table: <HP     0944    >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ACPI Error (tbfadt-0516): 32/64X address mismatch in "Pm2ControlBlock": [    
8800] [       0    8100], using 64X [20070320]
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 10:34:18)
acpi0: <HPQOEM SLIC-MPC> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
unknown: I/O range not supported
acpi0: reservation of 0, 8000000 (3) failed
acpi0: reservation of 100000, fff00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x11> port 0x62,0x66 on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
powernow0: <PowerNow! K8> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
powernow1: <PowerNow! K8> on cpu1
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x4000-0x40ff mem 
0xc0000000-0xc7ffffff,0xd0400000-0xd040ffff,0xd0500000-0xd05fffff irq 19 at 
device 5.0 on pci1
pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci16: <ACPI PCI bus> on pcib2
pci0:16:0:0: failed to read VPD data.
bge0: <Broadcom BCM5754/5787 A2, ASIC rev. 0xb002> mem 0xd0000000-0xd000ffff 
irq 16 at device 0.0 on pci16
miibus0: <MII bus> on bge0
brgphy0: <BCM5787 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge0: Ethernet address: 00:1f:29:85:3d:63
bge0: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pci32: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci48: <ACPI PCI bus> on pcib4
pci48: <network> at device 0.0 (no driver attached)
atapci0: <ATI ATA controller> port 
0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f mem 
0xd0609000-0xd06093ff irq 16 at device 18.0 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xd0601000-0xd0601fff irq 23 at 
device 19.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xd0602000-0xd0602fff irq 17 at 
device 19.1 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ohci2: <OHCI (generic) USB controller> mem 0xd0603000-0xd0603fff irq 17 at 
device 19.2 on pci0
ohci2: [GIANT-LOCKED]
ohci2: [ITHREAD]
usb2: OHCI version 1.0, legacy support
usb2: <OHCI (generic) USB controller> on ohci2
usb2: USB revision 1.0
uhub2: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ohci3: <OHCI (generic) USB controller> mem 0xd0604000-0xd0604fff irq 17 at 
device 19.3 on pci0
ohci3: [GIANT-LOCKED]
ohci3: [ITHREAD]
usb3: OHCI version 1.0, legacy support
usb3: <OHCI (generic) USB controller> on ohci3
usb3: USB revision 1.0
uhub3: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ohci4: <OHCI (generic) USB controller> mem 0xd0605000-0xd0605fff irq 17 at 
device 19.4 on pci0
ohci4: [GIANT-LOCKED]
ohci4: [ITHREAD]
usb4: OHCI version 1.0, legacy support
usb4: <OHCI (generic) USB controller> on ohci4
usb4: USB revision 1.0
uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd0606000-0xd06060ff irq 23 at 
device 19.5 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb5: EHCI version 1.0
usb5: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4
usb5: <EHCI (generic) USB 2.0 controller> on ehci0
usb5: USB revision 2.0
uhub5: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5
uhub5: 10 ports with 10 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP600 UDMA133 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x5040-0x504f irq 16 at device 20.1 on 
pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib5: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci2: <ACPI PCI bus> on pcib5
cbb0: <RF5C476 PCI-CardBus Bridge> mem 0xd0100000-0xd0100fff irq 20 at device 
4.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
fwohci0: <1394 Open Host Controller Interface> mem 0xd0101000-0xd01017ff irq 
21 at device 4.1 on pci2
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3f:99:29:21:1d:10
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x15dc000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:02:3f:21:1d:10
fwe0: Ethernet address: 02:02:3f:21:1d:10
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:02:3f:99:29:21:1d:10 @ 0xfffe00000000, S400, 
maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
ppc0: <Parallel port> port 0-0x7,0x400-0x402 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppi0: <Parallel I/O> on ppbus0
orm0: <ISA Option ROM> at iomem 0xd0000-0xd0fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ugen0: <Broadcom Corp HP Integrated Module, class 224/1, rev 2.00/1.00, addr 
2> on uhub0
umass0: <CRUCIAL USB DRIVE, class 0/0, rev 1.10/0.01, addr 2> on uhub1
ugen1: <vendor 0x08ff Fingerprint Sensor, class 255/255, rev 1.10/6.23, addr 
2> on uhub2
Timecounters tick every 1.000 msec
hptrr: no controller detected.
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xffffffff80bc6c08
acd0: DVDR <HL-DT-ST DVDRAM GSA-T20L/NC08> at ata0-master PIO4
ad4: 114473MB <Seagate ST9120822AS 3.BHE> at ata2-master UDMA33
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 
GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD_LiveFS.
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 
GEOM_LABEL: Label for provider ad4s3 is ntfs/HP_RECOVERY.
GEOM_LABEL: Label for provider ad4s4 is ntfs/OS_TOOLS.
SMP: AP CPU #1 Launched!
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <CRUCIAL USB DRIVE 1.12> Removable Direct Access SCSI-CCS device 
da0: 1.000MB/s transfers
da0: 61MB (125952 512 byte sectors: 64H 32S/T 61C)
GEOM_LABEL: Label for provider da0s1 is msdosfs/CRUCIAL.
Trying to mount root from ufs:/dev/md0
GEOM_LABEL: Label msdosfs/CRUCIAL removed.
GEOM_LABEL: Label for provider da0s1 is msdosfs/CRUCIAL.
GEOM_LABEL: Label msdosfs/CRUCIAL removed.

#######################################################################
Here is the NetBSD dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0 (GENERIC) #0: Sat Dec 15 22:25:31 PST 2007
	
builds at wb28:/home/builds/ab/netbsd-4-0-RELEASE/amd64/200712160005Z-obj/home/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/amd64/compile/GENERIC
total memory = 3967 MB
avail memory = 3815 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
mainbus0 (root)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Turion(tm) 64 X2 Mobile Technology TL-64, 2195.04 MHz
cpu0: features: ffdbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features: ffdbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,MMXX,MMX>
cpu0: features: ffdbfbff<FXSR,SSE,SSE2,B27,HTT,LONG,3DNOW2,3DNOW>
cpu0: features2: 2001<SSE3>
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 512 KB 64B/line 16-way
cpu0: ITLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: AMD Power Management features: 7f<STC,TM,TTP,VID,FID,TS>
cpu0: AMD PowerNow! Technology 2200 MHz
cpu0: available frequencies (Mhz): 800 1600 1800 2000 2200
cpu0: calibrating local timer
cpu0: apic clock running at 199 MHz
cpu0: 8 page colors
cpu1 at mainbus0: apid 1 (application processor)
cpu1: not started
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 21, 24 pins
ioapic0: misconfigured as apic 0
ioapic0: remapped to apic 2
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <HPQOEM,SLIC-MPC,00000001>, AslId <HP  ,00000001>
ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A1 (name not of form 
_Lxx or _Exx) [20060217]
ACPI Error (evgpeblk-0394): Unknown GPE method type: C28C (name not of form 
_Lxx or _Exx) [20060217]
ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A2 (name not of form 
_Lxx or _Exx) [20060217]
ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A3 (name not of form 
_Lxx or _Exx) [20060217]
ACPI Error (evgpeblk-0394): Unknown GPE method type: C253 (name not of form 
_Lxx or _Exx) [20060217]
ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A4 (name not of form 
_Lxx or _Exx) [20060217]
ACPI Error (evgpeblk-0394): Unknown GPE method type: C3A5 (name not of form 
_Lxx or _Exx) [20060217]
ACPI Error (evgpeblk-0394): Unknown GPE method type: C262 (name not of form 
_Lxx or _Exx) [20060217]
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 32-bit timer
mpacpi: could not get bus number, assuming bus 0
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C01 [System Board] at acpi0 not configured
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
PNP0A06 [Generic Container Device] at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
IFX0102 at acpi0 not configured
PNP0C04 [Math Coprocessor] at acpi0 not configured
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PNP0200 [AT DMA Controller] at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
pcppi1: children must have an explicit unit
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pckbc1 at acpi0 (PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (SYN0131): aux port
pckbc2: irq 12
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
HPQ0004 at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
HPQ0006 at acpi0 not configured
acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
acpibut0 at acpi0 (PNP0C0E): ACPI Sleep Button
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
PNP0C14 at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
PNP0C0B [ACPI Fan] at acpi0 not configured
PNP0C0B [ACPI Fan] at acpi0 not configured
PNP0C0B [ACPI Fan] at acpi0 not configured
PNP0C0B [ACPI Fan] at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: active cooling level 0: 70.0C
acpitz0: active cooling level 1: 60.0C
acpitz0: active cooling level 2: 50.0C
acpitz0: active cooling level 3: 40.0C
acpitz0: critical 105.0C passive 38.0C
pcppi1: attached to attimer1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 6.2
pms0: Palm detect, Multi-finger
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: ATI Technologies product 0x7910 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: ATI Technologies product 0x7912 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 5 function 0: ATI Technologies product 0x791f (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
ppb1 at pci0 dev 4 function 0: ATI Technologies product 0x7914 (rev. 0x00)
pci2 at ppb1 bus 16
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci2 dev 0 function 0: Broadcom BCM5787M Gigabit Ethernet
bge0: interrupting at ioapic0 pin 16 (irq 10)
bge0: ASIC BCM5754/5787 A2 (0xb002), Ethernet address 00:1f:29:85:3d:63
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5754/5787 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb2 at pci0 dev 5 function 0: ATI Technologies product 0x7915 (rev. 0x00)
pci3 at ppb2 bus 32
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 6 function 0: ATI Technologies product 0x7916 (rev. 0x00)
pci4 at ppb3 bus 48
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
Broadcom BCM4312 (miscellaneous network, revision 0x02) at pci4 dev 0 function 
0 not configured
ixpide0 at pci0 dev 18 function 0
ixpide0: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to native-PCI mode
ixpide0: using ioapic0 pin 16 (irq 10) for native-PCI interrupt
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to native-PCI mode
atabus1 at ixpide0 channel 1
ohci0 at pci0 dev 19 function 0: ATI Technologies product 0x4387 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 23 (irq 11)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1 at pci0 dev 19 function 1: ATI Technologies product 0x4388 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 17 (irq 5)
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ohci2 at pci0 dev 19 function 2: ATI Technologies product 0x4389 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 17 (irq 5)
ohci2: OHCI version 1.0, legacy support
usb2 at ohci2: USB revision 1.0
uhub2 at usb2
uhub2: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ohci3 at pci0 dev 19 function 3: ATI Technologies product 0x438a (rev. 0x00)
ohci3: interrupting at ioapic0 pin 17 (irq 5)
ohci3: OHCI version 1.0, legacy support
usb3 at ohci3: USB revision 1.0
uhub3 at usb3
uhub3: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ohci4 at pci0 dev 19 function 4: ATI Technologies product 0x438b (rev. 0x00)
ohci4: interrupting at ioapic0 pin 17 (irq 5)
ohci4: OHCI version 1.0, legacy support
usb4 at ohci4: USB revision 1.0
uhub4 at usb4
uhub4: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 19 function 5: ATI Technologies product 0x4386 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 23 (irq 11)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: ohci0 ohci1 ohci2 ohci3 ohci4
usb5 at ehci0: USB revision 2.0
uhub5 at usb5
uhub5: ATI Technologies EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 10 ports with 10 removable, self powered
ATI Technologies product 0x4385 (SMBus serial bus, revision 0x14) at pci0 dev 
20 function 0 not configured
ixpide1 at pci0 dev 20 function 1
ixpide1: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide1: bus-master DMA support present
ixpide1: primary channel configured to compatibility mode
ixpide1: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus2 at ixpide1 channel 0
ixpide1: secondary channel wired to compatibility mode
ixpide1: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus3 at ixpide1 channel 1
azalia0 at pci0 dev 20 function 2: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 16 (irq 10)
azalia0: host: 0x1002/0x4383 (rev. 0)
azalia0: host: High Definition Audio rev. 1.0
pcib0 at pci0 dev 20 function 3
pcib0: ATI Technologies product 0x438d (rev. 0x00)
ppb4 at pci0 dev 20 function 4: ATI Technologies product 0x4384 (rev. 0x00)
pci5 at ppb4 bus 2
pci5: i/o space, memory space enabled
cbb0 at pci5 dev 4 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 0xb6)
fwohci0 at pci5 dev 4 function 1: Ricoh product 0x0832 (rev. 0x02)
fwohci0: interrupting at ioapic0 pin 21 (irq 5)
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3f:99:29:21:1d:10
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
cbb0: interrupting at ioapic0 pin 20 (irq 10)
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3
pcmcia0 at cardslot0
pchb1 at pci0 dev 24 function 0
pchb1: Advanced Micro Devices AMD64 HyperTransport configuration (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: Advanced Micro Devices AMD64 Address Map configuration (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: Advanced Micro Devices AMD64 DRAM configuration (rev. 0x00)
pchb4 at pci0 dev 24 function 3
pchb4: Advanced Micro Devices AMD64 Miscellaneous configuration (rev. 0x00)
isa0 at pcib0
ioapic0: enabling
WARNING: Callback scheduled before sysmon task queue thread present.
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: Analog Devices AD1981HD (rev. 2.0)
azalia0: codec[0]: High Definition Audio rev. 1.0
azalia0: playback: max channels=2, encodings=1<PCM>
azalia0: playback: PCM 
formats=e007f<24bit,20bit,16bit,48kHz,44.1kHz,32kHz,22.05kHz,16kHz,11.025kHz,8kHz>
azalia0: recording: max channels=2, encodings=1<PCM>
azalia0: recording: PCM 
formats=6007f<20bit,16bit,48kHz,44.1kHz,32kHz,22.05kHz,16kHz,11.025kHz,8kHz>
azalia0: codec[1]: 0x11c1/0x1040 (rev. 2.0)
azalia0: codec[1]: High Definition Audio rev. 1.0
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
Kernelized RAIDframe activated
acpibat0: battery info: Hewlett-Packard, LIon, Primary, 48204 2008/04/13
ugen0 at uhub2 port 1
ugen0: AuthenTec Fingerprint Sensor, rev 1.10/6.23, addr 2
wd0 at atabus0 drive 0: <ST9120822AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 111 GB, 232581 cyl, 16 head, 63 sec, 512 bytes/sect x 234441648 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus2: 2 targets
cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GSA-T20L, KZ183LD5612, NC08> cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(ixpide1:0:0): using PIO mode 4, DMA mode 2 (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
WARNING: clock gained 7 days
WARNING: CHECK AND RESET THE DATE!
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)






On Sunday 11 May 2008 07:49:47 you wrote:
> On Sat, 2008-05-10 at 14:33 -0400, Coleman Kane wrote:
> > On Sat, 2008-05-10 at 12:13 -0500, rar102 at ra.msstate.edu wrote:
> > > Quoting Coleman Kane <cokane at freebsd.org>:
> > >
> > > Yes!!! thank you.  Unfortunately, I don't have access to another amd64
> > > box to try your patch.  Sorry.  But, I will look at the dmesg and send
> > > it to you.
> >
> > Excellent. A dmesg will be very helpful for me to write a patch from, as
> > it will allow me to see if it is or is not the sound driver overlapping
> > memory in your case. I suspect that the BIOS images are so similar that
> > you probably even have almost the same bios-chosen memory regions on
> > your system.
>
> If you're having difficulty getting a dmesg, you might want to try
> booting off the LiveFS disc with a USB flash drive plugged in. You can
> then mount the flash drive (which should be detected as SCSI) and write
> the dmesg output there.
>
> > > > RAR,
> > > >
> > > > You are in luck! Well, actually I have good news and I have bad news.
> > > > The good news is that I have nearly the same (6715b) laptop and
> > > > experienced similar problems when getting FreeBSD onto it. After some
> > > > work, I've been able to use FreeBSD reliably on the system.
> > > >
> > > > The bad news is that you probably have an overlap of PCI memory
> > > > ranges between the SATA controller and another device in the system
> > > > (likely the audio controller).
> > > >
> > > > I put up a page describing the problem here:
> > >
> > > http://www.cokane.org/dokuwiki/freebsd/amd64_compatibility#getting_the_
> > >hp_compaq_6715b_working
> > >
> > > > Specifically, read this section:
> > >
> > > http://www.cokane.org/dokuwiki/freebsd/amd64_compatibility#the_onboard_
> > >ati_sb600_hda_audio_controller
> > >
> > > > Give me the weekend, and I will post a 7.0-RELEASE CD with the patch
> > > > in it. I figured that I should have done it a while ago. Oh well.
> > > >
> > > > While you are at it, see if you can use Scroll-Lock and the up/down
> > > > keys to read the kernel messages. See if you can find the atapci0
> > > > probe line for your SATA controller (AHCI), as well as the line for
> > > > your pcm0 device and send them back to me. I can add your info to my
> > > > webpage to help others.
> > > >
> > > > It will look like this:
> > > > atapci0: <ATI IXP600 SATA300 controller> port
> > > > 0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f
> > > > mem 0xd0609000-0xd06093ff irq 16 at device 18.0 on pci0
> > > > ...
> > > > pcm0: <ATI SB600 High Definition Audio Controller> mem
> > > > 0xd0608000-0xd060bfff irq 16 at device 20.2 on pci0
> > > >
> > > > You'll notice the "mem" resource for the audio controller is
> > > > 0xd0608000-0xd060bff, and the "mem" resource for the SATA controller
> > > > is 0xd0609000-0xd06093ff. The SATA controller's "mem" resource is
> > > > completely covered by this audio controller.
> > > >
> > > > If you happen to have access to another machine for building your own
> > > > releases, you can try my patch and build them from it.
> > > >
> > > > --
> > > > Coleman Kane

-- 
Robertsen A. Riehle

More information about the freebsd-arch mailing list