toshiba portege r100 doesn't resume from S3
Russell Jackson
raj at cserv62.csub.edu
Sat Dec 17 19:46:32 PST 2005
I reported a similar problem on my Portege 4010 to gnats and
freebsd-current yesterday. I wasn't sure if it was limited to
ACPI, so I didn't post it here.
problem report:
http://www.freebsd.org/cgi/query-pr.cgi?pr=i386/90519
FYI, dmesg gets it's output from kernel memory.
On Fri, Dec 09, 2005 at 03:38:53PM +0300, huge at nm.ru wrote:
>
> Hi! I have a problem. Would you help me?
>
> My Toshiba Portege R100 doesn't resume from S3.
>
> There is a problem with disk access after resume. It looks the same if I did
> "atacontrol detach ata0". And that's interesting: ad0 is
> detached but error messages are successfully logged.
>
> [from dmesg]
> ..........
> acpi_button0: run_prep cleaned up for \\_SB_.PWRB
> acpi_lid0: run_prep cleaned up for \\_SB_.LID_
> acpi: suspend request ignored (not ready yet)
> cbb0: [MPSAFE]
> ata0: reiniting channel ..
> ata0: reset tp1 mask=03 ostat0=80 ostat1=80
> ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
> ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
> ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
> ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
> ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
> ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
> ata0: stat0=0x50 err=0x00 lsb=0xfe msb=0x3f
> ata0: stat1=0x00 err=0x00 lsb=0xfe msb=0x3f
> ata0: reset tp2 stat0=50 stat1=00 devices=0x0
> --> ad0: detached
> ata0: reinit done ..
> ata1: reiniting channel ..
> ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
> ata1: reinit done ..
> atkbd: the current kbd controller command byte 0065
> atkbd: keyboard ID 0x41ab (2)
> battery0: battery initialization start
> battery0: battery initialization done, tried 1 times
> battery1: battery initialization start
> --> g_vfs_done():ad0s1a[READ(offset=277413888, length=2560)]error = 6
> vnode_pager_getpages: I/O read error
> --> g_vfs_done():ad0s1a[READ(offset=268517376, length=12800)]error = 6
> vnode_pager_getpages: I/O read error
> --> g_vfs_done():ad0s1e[WRITE(offset=6144000, length=2048)]error = 6
> --> g_vfs_done():ad0s1e[WRITE(offset=65536, length=2048)]error = 6
> panic: vinvalbuf: dirty bufs
> Uptime: 33m47s
> Cannot dump. No dump device defined.
> Automatic reboot in 15 seconds - press a key on the console to abort
> --> Press a key on the console to reboot,
> --> or switch off the system now.
> Rebooting...
> .........
>
>
>
> And there is another problem. Video doesn't work after resume.
> With hw.acpi.reset_video=1 display is just off, with 0 it shows
> multicolored vertical lines.
>
> The DSDT seems to be ok since it's recompiled without errors and the
> same machine successfully resumes from S3 under linux.
>
>
>
> # dmesg
> http://media-trest.ru/r100/dmesg-v
>
>
>
> # sysctl hw.acpi
> http://media-trest.ru/r100/sysctl
>
>
>
> ASL
> http://media-trest.ru/r100/toshiba-portege-r100.asl
>
>
>
>
> Thanks!
> Alexandre Scherbanov
>
> _______________________________________________
> freebsd-acpi at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-acpi
> To unsubscribe, send any mail to "freebsd-acpi-unsubscribe at freebsd.org"
--
Russell A. Jackson <raj at csub.edu>
Come quickly, I am tasting stars!
-- Dom Perignon, upon discovering champagne.
More information about the freebsd-acpi
mailing list