cvs commit: src/sys/dev/bfe if_bfe.c if_bfereg.h

[Pyun YongHyeon]

yongari     2008-08-21 04:21:53 UTC

  FreeBSD src repository

  Modified files:
    sys/dev/bfe          if_bfe.c if_bfereg.h 
  Log:
  SVN rev 181953 on 2008-08-21 04:21:53Z by yongari
  
   o Sort includes and add <endian.h> to support endianness.
   o Removed unneeded header files.
   o bus_dma(9) fix:
     - created parent tag with 1GB dma address limit with no
       alignment restrictions.
     - set 4096 alignment limit for Tx/Rx descriptor rings.
     - separate Rx buffer tag from Tx buffer tag such that Tx tag
       allows up-to 16 segments while Rx buffer tag only allows
       single segment.
     - it seems the controller has no alignment restrictions on Tx/Rx
       buffers. Remove ETHER_ALIGN alignment restriction in Tx/Rx
       buffers.
     - created a spare Rx dma map which would be used to cope with
       failure of loading a dma map.
     - make sure to load full Tx/Rx descriptor size for Tx/Rx
       descriptor dma maps, previously bfe(4) used to load single
       descriptor size for each descriptor rings. I have no idea how
       it could be run without problems.
     - don't blindly cast bus_addr_t type to 32bits in bfe_dma_map().
     - created bfe_dma_free() to free allocated dma memory/tags.
     - make sure to invoke bus_dmamap_sync(9) before/after processing
       descriptor rings/buffers. Because the hardware has severe dma
       address space limitation, bounce-buffers would be always used
       on systems with more than 1GB memory during
       descriptors/buffers access.
     - added Tx descriptor ring initialization function,
       bfe_list_tx_init().
     - moved producer/consumer index initialization to
       bfe_list_tx_init() and bfe_list_rx_init() from
       bfe_chip_reset().
     - added bfe_discard_buf() which will update loaded descriptors
       without unloading/reloading the dma map to speed up error
       recovery.
     - implemented Tx side bus_dmamap_load_mbuf_sg(9). The number of
       segments allowed was chosen to be 16 which should be enough for
       non-TSO capable hardwares. Setting SOF bit of Tx descriptor is
       done in the last to avoid potential race.
     - don't give up sending frames in bfe_start() until the hardware
       lacks free descriptors.
     - added XXX comment to second kick command and possible workaround.
     - implemented Rx side bus_dmamap_load_mbuf_sg(9).
     - removed bfe_dma_map_desc() as it's not needed anymore after
       the conversion to bus_dmamap_load_mbuf_sg(9).
     - added endianness support. With this change bfe(4) should work
       on any architectures that can create bounce buffers within 1GB
       address range.
     - add missing bus_dmamap_sync() in bfe_tx_eof()/bfe_rx_eof().
   o Use PCI_BAR instead of hardcoded value to set BARs.
     Simplified register access with bus_write_4(9)/bus_read_4(9) and
     removed bfe_btag, bfe_bhandle, bfe_vhandle in softc as it's not
     used anymore.
   o Reorder device detach logic such that bfe_detach() is also used
     for handling driver attach failure case.
   o Remove unnecessary KASSERT in bfe_detach().
   o Remove bfe_rx_cnt, bfe_up, bfe_vpd_prodname, bfe_vpd_readonly in
     softc.  It's not used at all.
   o Remove BFE_RX_RING_SIZE/BFE_RX_RING_SIZE/BFE_LINK_DOWN.
  
  Tested by:      kib, Gleb Kurtsou gleb.kurtsou at gmail dot com
                  Ulrich Spoerlein uspoerlein at gmail dot com
  
  Revision  Changes    Path
  1.51      +474 -353  src/sys/dev/bfe/if_bfe.c
  1.13      +20 -17    src/sys/dev/bfe/if_bfereg.h