Tape Drive Not Detected

[a-m-g01 at home.com]

Hi,

Under my old setup (aic7xxx driver version 4.1.1 with kernel version
2.0.33) I had no problems with my WangDAT 3200 tape drive. 

However when I installed SuSE Linux 6.3 (aic7xxx driver version 5.1.21
with kernel version 2.2.13)  the drive was no longer detected. 

The hardware configuration has not changed, and the Internal CDRom is
always detected and works perfectly.

I have patched aic7xxx up to version 5.1.28, but the drive is still
not detected.

Any suggestions as to what I need to do to solve this problem would be
appreciated.

Thanks
Alun

-------------------------------------------

Boot Messages:

<6>(scsi0) <Adaptec AIC-7850 SCSI host adapter> found at PCI 11/0
<6>(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
<6>(scsi0) Warning - detected auto-termination
<6>(scsi0) Please verify driver detected settings are correct.
<6>(scsi0) If not, then please properly set the device termination
<6>(scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
<6>(scsi0) during machine bootup.
<6>(scsi0) Cables present (Int-50 YES, Ext-50 YES)
<6>(scsi0) Downloading sequencer code... 406 instructions downloaded
<4>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI)
5.1.20/3.2.4 <4>       <Adaptec AIC-7850 SCSI host adapter>
<4>scsi : 1 host.
<6>(scsi0:0:6:0) Synchronous at 4.0 Mbyte/sec, offset 15.
<4>  Vendor: TOSHIBA   Model: CD-ROM XM-3601TA  Rev: 0725
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
<6>Uniform CDROM driver Revision: 2.56

-------------------------------------------

/proc/scsi/scsi

Attached devices: 
Host: scsi0 Channel: 00 Id: 06 Lun: 00
  Vendor: TOSHIBA  Model: CD-ROM XM-3601TA Rev: 0725
  Type:   CD-ROM                           ANSI SCSI revision: 02
Adaptec AIC7xxx driver version: 5.1.20/3.2.4

-------------------------------------------

/proc/scsi/aic7xxx/0

Compile Options:
  TCQ Enabled By Default : Disabled
  AIC7XXX_PROC_STATS     : Disabled
  AIC7XXX_RESET_DELAY    : 5

Adapter Configuration:
           SCSI Adapter: Adaptec AIC-7850 SCSI host adapter
Narrow Controller
    PCI MMAPed I/O Base: 0xe1004000
 Adapter SEEPROM Config: SEEPROM found and used.
      Adaptec SCSI BIOS: Disabled
                    IRQ: 10
                   SCBs: Active 0, Max Active 1,
                         Allocated 15, HW 3, Page 255
             Interrupts: 513
      BIOS Control Word: 0x0100
   Adapter Control Word: 0x001d
   Extended Translation: Disabled
Disconnect Enable Flags: 0x00ff
 Tag Queue Enable Flags: 0x0000
Ordered Queue Tag Flags: 0x0000
Default Tag Queue Depth: 8
    Tagged Queue By Device array for aic7xxx host instance 0:
{255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
Actual queue depth per device for aic7xxx host instance 0:
{1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}

Statistics:

(scsi0:0:2:0)
  Device using Narrow/Async transfers.
  Transinfo settings: current(0/0/0/0), goal(0/0/0/0), user(25/15/0/0)
Total transfers 0 (0 reads and 0 writes)


(scsi0:0:6:0)
  Device using Narrow/Sync transfers at 4.0 MByte/sec, offset 15
Transinfo settings: current(59/15/0/0), goal(25/15/0/0),
user(25/15/0/0)   Total transfers 382 (382 reads and 0 writes)

-------------------------------------------
 



To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message