Error from aic7xxx
tmuller at agora.rdrop.com
tmuller at agora.rdrop.com
Wed Aug 11 17:29:03 PDT 1999
Hi all,
Well, I've got some good news and some bad news. The good news is that this
seems to have cleared up once I put the jumper on the "Disable Target Initiated
Syncronous/Wide Negotiation". So now the bad news. I still see one of
these errors during bootup, but only one. Now dmesg is:
(scsi0) <Adaptec AIC-7895 Ultra SCSI host adapter> found at PCI 9/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 374 instructions downloaded
(scsi1) <Adaptec AIC-7895 Ultra SCSI host adapter> found at PCI 9/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 374 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.19/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.19/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi : 2 hosts.
(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 8.
Vendor: IBM Model: DORS-32160W !# Rev: WA3E
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 40.0 Mbyte/sec, offset 8.
Vendor: IBM Model: DGHS09U Rev: 0350
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:0:2:0) Synchronous at 40.0 Mbyte/sec, offset 8.
Vendor: MICROP Model: 4341WS Rev: x43h
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
(scsi0:0:3:0) Synchronous at 40.0 Mbyte/sec, offset 8.
(scsi0:0:3:0) Data overrun detected in Data-In phase, tag 1;
Have seen Data Phase. Length=255, NumSGs=1.
sg[0] - Addr 0x7fe86e0 : Length 255
Vendor: WDIGTL Model: ENTERPRISE Rev: 1.91
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdd at scsi0, channel 0, id 3, lun 0
(scsi1:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: PLEXTOR Model: CD-ROM PX-20TS Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi1, channel 0, id 4, lun 0
(scsi1:0:6:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: SAF Model: CD-RW226 Rev: 1.40
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi1, channel 0, id 6, lun 0
scsi : detected 2 SCSI cdroms 4 SCSI disks total.
Uniform CDROM driver Revision: 2.55
sr1: scsi3-mmc drive: 0x/0x caddy
SCSI device sda: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 8070564 [3940 MB] [3.9 GB]
SCSI device sdd: hdwr sector= 512 bytes. Sectors= 8515173 [4157 MB] [4.2 GB]
Ok, what do you think? Is it going to be safe to use? I can't believe that
the messages are damaging since just by turning off the target negotiations
all but removed them. Comments Doug?
Btw, setting the tagged queuing to none does not make a different in the error
showing up. I tried it via lilo and also by disabling it in the kernel build. The same error shows up in both situations.
--
Thanks,
Troy
----------------------------------------------------------------
email: tmuller at agora.rdrop.com
PGP 5.0 key: hkp://pgp.ai.mit.edu
helpful suggestion:
perl -e 'print $i=pack(c5,(41*2),sqrt(7056),(unpack(c,H)-2),oct(115),10);'
----------------------------------------------------------------
To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message
More information about the aic7xxx
mailing list