Proc Stats question

[Bill Luckett]

Hi,

I'm using an AIC7890 with pre15 on a Dell Prescision 410 with 2 quantum
Vikings. I've set CONFIG_AIC7XXX_PROC_STATS=y in my .config file but the
kernel I compile puts no stats in the files /proc/scsi/aic7xxx/0 or 1. How
do I get it to create stats or can I just assume from the boot messages
below that I'm getting synchromous, 80 Mbyte/sec transfers?

Also, should I be concerned about the "detected auto-termination" warning.
Auto termination is enabled on the card and I was under the impression that
this was a good (or at least acceptable) thing. Was I told wrong?

Except for these questions the driver apears to be working fine.


(scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 10/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 407 instructions downloaded
(scsi1) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 14/0
(scsi1) Wide Channel, SCSI ID=7, 16/255 SCBs
aic7xxx: Warning - detected auto-termination on controller:
aic7xxx: <Adaptec AIC-7880 Ultra SCSI host adapter> at PCI 14/0
aic7xxx: Please verify driver detected settings are correct.
aic7xxx: If not, then please properly set the device termination
aic7xxx: in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
aic7xxx: during machine bootup.
aic7xxx: Cables present (Int-50 NO, Int-68 NO, Ext-68 NO)
(scsi1) Downloading sequencer code... 419 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.0pre15/3.2.4
       <Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.0pre15/3.2.4
       <Adaptec AIC-7880 Ultra SCSI host adapter>
scsi : 2 hosts.
  Vendor: QUANTUM   Model: VIKING II 4.5WLS  Rev: 3506
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: QUANTUM   Model: VIKING II 4.5WLS  Rev: 3506
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
  Vendor: NEC       Model: CD-ROM DRIVE:465  Rev: 1.03
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi1, channel 0, id 5, lun 0
  Vendor: Seagate   Model: STT8000N          Rev: 3.22
  Type:   Sequential-Access                  ANSI SCSI revision: 02
Detected scsi tape st0 at scsi1, channel 0, id 6, lun 0
scsi : detected 1 SCSI tape 1 SCSI cdrom 2 SCSI disks total.
(scsi0:0:0:0) Synchronous at 80.0 Mbyte/sec, offset 31.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8910423 [4350 MB] [4.4 GB]
(scsi0:0:1:0) Synchronous at 80.0 Mbyte/sec, offset 31.
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8910423 [4350 MB] [4.4 GB]

*************************************************************
Bill Luckett
Phi Theta Kappa International Honor Society
Center for Excellence
Mississippi Education and Research Center
1625 Eastover Drive
Jackson, MS 39211

bill.luckett at ptk.org
601.957.2241 ext 559
*************************************************************

To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe freebsd-aic7xxx" in the body of the message