5.0.18: "Bad scbptr 255 during SELTO"
Elgin Lee
ehl at funghi.com
Fri Jun 12 11:38:49 PDT 1998
I upgraded to 5.0.19, but the
(scsi0:-1:-1:-1) Bad scbptr 255 during SELTO.
(scsi0:-1:-1:-1) Referenced SCB 255 not valid during SELTO.
SCSISEQ = 0x12 SEQADDR = 0xb SSTAT0 = 0x10 SSTAT1 = 0x8a
error messages are still with me.
This boot, the driver also seems to have missed my Zip drive and
Plextor SCSI CD-ROM.
Here's further information about my system:
- 3 hard disks:
Seagate ST32550N
IBM DORS-32160
Quantum Viking 4.5 NSE
- Iomega SCSI Zip drive
- Plextor 12x SCSI CD-ROM
- UMAX Vista S-6E scanner (in the middle of one of my external
SCSI chains, but not turned on during this boot)
Here's the output from /proc:
[ehl at porcini ehl]$ cat /proc/scsi/aic7xxx/0
Adaptec AIC7xxx driver version: 5.0.19/3.2.4
Compile Options:
AIC7XXX_RESET_DELAY : 5
AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled
Check below to see which
devices use tagged queueing
AIC7XXX_PAGE_ENABLE : Enabled (This is no longer an option)
AIC7XXX_PROC_STATS : Disabled
Adapter Configuration:
SCSI Adapter: Adaptec AHA-294X Ultra SCSI host adapter
Ultra Wide Controller
PCI MMAPed I/O Base: 0xffbeb000
Adaptec SCSI BIOS: Enabled
IRQ: 10
SCBs: Active 0, Max Active 1,
Allocated 30, HW 16, Page 255
Interrupts: 4968
BIOS Control Word: 0x18b6
Adapter Control Word: 0x005f
Extended Translation: Enabled
Disconnect Enable Flags: 0xffff
Ultra Enable Flags: 0xfffc
Tag Queue Enable Flags: 0x0000
Ordered Queue Tag Flags: 0x0000
Default Tag Queue Depth: 8
Tagged Queue By Device array for aic7xxx host instance 0:
{255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
Actual queue depth per device for aic7xxx host instance 0:
{1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
[ehl at porcini ehl]$ cat /proc/scsi/aic7xxx/1
Adaptec AIC7xxx driver version: 5.0.19/3.2.4
Compile Options:
AIC7XXX_RESET_DELAY : 5
AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled
Check below to see which
devices use tagged queueing
AIC7XXX_PAGE_ENABLE : Enabled (This is no longer an option)
AIC7XXX_PROC_STATS : Disabled
Adapter Configuration:
SCSI Adapter: Adaptec AHA-294X Ultra SCSI host adapter
Ultra Wide Controller
PCI MMAPed I/O Base: 0xffbea000
Adaptec SCSI BIOS: Enabled
IRQ: 3
SCBs: Active 0, Max Active 1,
Allocated 30, HW 16, Page 255
Interrupts: 6135
BIOS Control Word: 0x18b6
Adapter Control Word: 0x005b
Extended Translation: Enabled
Disconnect Enable Flags: 0xffff
Ultra Enable Flags: 0xffff
Tag Queue Enable Flags: 0x0000
Ordered Queue Tag Flags: 0x0000
Default Tag Queue Depth: 8
Tagged Queue By Device array for aic7xxx host instance 1:
{255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
Actual queue depth per device for aic7xxx host instance 1:
{1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
[ehl at porcini ehl]$ cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST32550N Rev: 0019
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: IBM Model: DORS-32160 Rev: S82C
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: QUANTUM Model: VIKING 4.5 NSE Rev: 8808
Type: Direct-Access ANSI SCSI revision: 02
Here's the dmesg output:
aic7xxx: Warning - detected auto-termination on controller:
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 15/0
aic7xxx: Please verify driver detected settings are correct.
aic7xxx: If not, then please properly set the device termination
aic7xxx: in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
aic7xxx: during machine bootup.
aic7xxx: Cables present (Int-50 YES, Int-68 NO, Ext-68 NO)
aic7xxx: Termination (Low ON, High ON)
aic7xxx: Warning - detected auto-termination on controller:
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 11/0
aic7xxx: Please verify driver detected settings are correct.
aic7xxx: If not, then please properly set the device termination
aic7xxx: in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
aic7xxx: during machine bootup.
aic7xxx: Cables present (Int-50 YES, Int-68 NO, Ext-68 YES)
aic7xxx: Termination (Low OFF, High ON)
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 15/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) BIOS enabled, IO Port 0xfc00, IRQ 10
(scsi0) IO Memory at 0xffbeb000, MMAP Memory at 0x481d000
(scsi0) Resetting channel
(scsi0) Downloading sequencer code... 413 instructions downloaded
(scsi1) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 11/0
(scsi1) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi1) BIOS enabled, IO Port 0xf800, IRQ 3
(scsi1) IO Memory at 0xffbea000, MMAP Memory at 0x481f000
(scsi1) Resetting channel
(scsi1) Downloading sequencer code... 413 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.19/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.19/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 2 hosts.
(scsi0:0:-1:-1) Scanning channel for devices.
(scsi0:-1:-1:-1) Allocating initial 30 SCB structures.
Vendor: SEAGATE Model: ST32550N Rev: 0019
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: IBM Model: DORS-32160 Rev: S82C
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi1:0:-1:-1) Scanning channel for devices.
(scsi1:-1:-1:-1) Allocating initial 30 SCB structures.
Vendor: QUANTUM Model: VIKING 4.5 NSE Rev: 8808
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi1, channel 0, id 0, lun 0
(scsi0:-1:-1:-1) Bad scbptr 255 during SELTO.
(scsi0:-1:-1:-1) Referenced SCB 255 not valid during SELTO.
SCSISEQ = 0x12 SEQADDR = 0xb SSTAT0 = 0x10 SSTAT1 = 0x8a
scsi : detected 3 SCSI disks total.
(scsi0:0:0:0) Synchronous at 10.0MHz, offset 15.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 4194058 [2047 MB] [2.0 GB]
(scsi0:0:1:0) Synchronous at 10.0MHz, offset 15.
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
(scsi1:0:0:0) Synchronous at 20.0MHz, offset 15.
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 8899737 [4345 MB] [4.3 GB]
PPP: version 2.2.0 (dynamic channel allocation)
TCP compression code copyright 1989 Regents of the University of California
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
eth0: 3Com 3c595 Vortex 100baseTX at 0xff80, 00:a0:24:95:e2:a6, IRQ 9
64K word-wide RAM 3:1 Rx:Tx split, autoselect/10baseT interface.
eth0: Overriding PCI latency timer (CFLT) setting of 24, new value is 248.
3c59x.c:v0.99E 5/12/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sdb: sdb1 < sdb5 sdb6 > sdb2 sdb3
sdc: sdc1 sdc2 sdc3 < sdc5 sdc6 sdc7 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 64224k swap-space (priority -1)
Appletalk 0.17 for Linux NET3.035
To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message
More information about the aic7xxx
mailing list