booting FreeBSD 13 release

Hello Justin,

I am trying to boot FreeBSD 13. How to I set loaderdev? It doesn't find 
the kernel.

Kind Regards,
Al






U-Boot 2014.04 (Oct 17 2016 - 08:22:22)

CPU0:  P5020, Version: 2.0, (0x82200020)
Core:  e5500, Version: 1.2, (0x80240012)
Clock Configuration:
        CPU0:1995 MHz, CPU1:1995 MHz,
        CCB:798  MHz,
        DDR:665  MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
        FMAN1: 498.750 MHz
        QMAN:  399 MHz
        PME:   399 MHz
L1:    D-cache 32 KiB enabled
        I-cache 32 KiB enabled
Reset Configuration Word (RCW):
        00000000: 0c540000 00000000 1e1e0000 00000000
        00000010: 44808c00 ff002000 68000000 45000000
        00000020: 00000000 00000000 00000000 0003000f
        00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C:   ready
SPI:   ready
DRAM:  Initializing....using SPD
Detected UDIMM KHX1600C10D3/8G
Detected UDIMM KHX1600C10D3/8G
14 GiB left unmapped
16 GiB (DDR3, 64-bit, CL=9, ECC off)
        DDR Controller Interleaving Mode: cache line
        DDR Chip-Select Interleaving Mode: CS0+CS1

Local Bus Controller Registers
BR0     0xE0001001      OR0     0xFFF00010
BR1     0xE1001001      OR1     0xFFF00010
BR2     0x00000000      OR2     0x00000000
BR3     0x00000000      OR3     0x00000000
BR4     0x00000000      OR4     0x00000000
BR5     0x00000000      OR5     0x00000000
BR6     0x00000000      OR6     0x00000000
BR7     0x00000000      OR7     0x00000000
LBCR    0x40000000      LCRR    0x80010004
L2:    512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC:  FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen1, regs @ 0xfe200000
   01:00.0     - 1002:6759 - Display controller
   01:00.1     - 1002:aa90 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
   03:00.0     - 111d:8092 - Bridge device
    04:01.0    - 111d:8092 - Bridge device
     05:00.0   - 12d8:e111 - Bridge device
    04:02.0    - 111d:8092 - Bridge device
    04:03.0    - 111d:8092 - Bridge device
     08:00.0   - 8086:10d3 - Network controller
    04:08.0    - 111d:8092 - Bridge device
    04:10.0    - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In:    serial
Out:   serial
Err:   serial
ID: NXID v0
SN: 116330081
UID: 4429431001910051c47da080a0800000
Errata: Q
Build date: 2015/07/06 14:51:17
CRC: eb5fb57a
SCSI:  scanning bus for devices...
Found 0 device(s).
Net:   Initializing Fman

MMC read: dev # 0, block # 1130, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5

MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK

MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK
USB0:   USB EHCI 1.00
scanning bus 0 for devices... ERROR: Invalid USB EP length (9)
ERROR: Invalid USB EP length (9)
4 USB Device(s) found
USB1:   USB EHCI 1.00
scanning bus 1 for devices... 4 USB Device(s) found
SATA0 (3 Gbps)
        SATA1 (No RDY)
scanning bus for devices...
Found 0 device(s).
X5000> setenv loader_kernaddr 0x2000000
X5000> fatload sata 0:1 $loadaddr ubldr
reading ubldr
315292 bytes read in 27 ms (11.1 MiB/s)
X5000> fatload sata 0:1 $fdtaddr cyrus.dtb
reading cyrus.dtb
65536 bytes read in 31 ms (2 MiB/s)
X5000> fdt addr $fdtaddr
X5000> fdt boardsetup
X5000> bootelf $loadaddr
## Starting application at 0x00010160 ...
Consoles: U-Boot console
Compatible U-Boot API signature found @0x7fe2efd8

FreeBSD/powerpc64 U-Boot loader, Revision 1.1

Number of U-Boot devices: 4
U-Boot env: loaderdev not set, will probe all devices.
Found U-Boot device: disk
   Probing all <unknown> devices...
   Checking unit=0 slice=<auto> partition=<auto>...
   Checking unit=1 slice=<auto> partition=<auto>...
   Checking unit=2 slice=<auto> partition=<auto>...Non-NCQ command time out
Non-NCQ command time out
Non-NCQ command time out

Found U-Boot device: net
Booting from net0:
bootp: no reply
No response for RARP request
net_open: RARP failed
bootp: no reply
No response for RARP request
net_open: RARP failed

bootp: no reply
No response for RARP request
net_open: RARP failed
bootp: no reply
No response for RARP request
net_open: RARP failed
bootp: no reply
No response for RARP request
net_open: RARP failed
bootp: no reply
No response for RARP request
net_open: RARP failed
bootp: no reply