yet another error

From: Al <al_at_datazap.net>
Date: Sun, 01 Aug 2021 19:31:30 UTC
Hello,

It is loading the kernel now, but there is a USB error:

U-Boot 2014.04 (Oct 17 2016 - 08:22:22)

CPU0:  P5020, Version: 2.0, (0x82200020)
Core:  e5500, Version: 1.2, (0x80240012)
Clock Configuration:
        CPU0:1995 MHz, CPU1:1995 MHz,
        CCB:798  MHz,
        DDR:665  MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
        FMAN1: 498.750 MHz
        QMAN:  399 MHz
        PME:   399 MHz
L1:    D-cache 32 KiB enabled
        I-cache 32 KiB enabled
Reset Configuration Word (RCW):
        00000000: 0c540000 00000000 1e1e0000 00000000
        00000010: 44808c00 ff002000 68000000 45000000
        00000020: 00000000 00000000 00000000 0003000f
        00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C:   ready
SPI:   ready
DRAM:  Initializing....using SPD
Detected UDIMM KHX1600C10D3/8G
Detected UDIMM KHX1600C10D3/8G
14 GiB left unmapped
16 GiB (DDR3, 64-bit, CL=9, ECC off)
        DDR Controller Interleaving Mode: cache line
        DDR Chip-Select Interleaving Mode: CS0+CS1

Local Bus Controller Registers
BR0     0xE0001001      OR0     0xFFF00010
BR1     0xE1001001      OR1     0xFFF00010
BR2     0x00000000      OR2     0x00000000
BR3     0x00000000      OR3     0x00000000
BR4     0x00000000      OR4     0x00000000
BR5     0x00000000      OR5     0x00000000
BR6     0x00000000      OR6     0x00000000
BR7     0x00000000      OR7     0x00000000
LBCR    0x40000000      LCRR    0x80010004
L2:    512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC:  FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen1, regs @ 0xfe200000
   01:00.0     - 1002:6759 - Display controller
   01:00.1     - 1002:aa90 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
   03:00.0     - 111d:8092 - Bridge device
    04:01.0    - 111d:8092 - Bridge device
     05:00.0   - 12d8:e111 - Bridge device
    04:02.0    - 111d:8092 - Bridge device
    04:03.0    - 111d:8092 - Bridge device
     08:00.0   - 8086:10d3 - Network controller
    04:08.0    - 111d:8092 - Bridge device
    04:10.0    - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In:    serial
Out:   serial
Err:   serial
ID: NXID v0
SN: 116330081
UID: 4429431001910051c47da080a0800000
Errata: Q
Build date: 2015/07/06 14:51:17
CRC: eb5fb57a
SCSI:  scanning bus for devices...
Found 0 device(s).
Net:   Initializing Fman

MMC read: dev # 0, block # 1130, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5

MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK

MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK
USB0:   USB EHCI 1.00
scanning bus 0 for devices... ERROR: Invalid USB EP length (9)
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by U-Boot at address 0xc00000.
Kernel args: (null)devices... 4 USB Device(s) found
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb..
---<<BOOT>>---(s).
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
X5000> fThe Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 14.0-CURRENT #4 main-n248384-d0d631d5f44: Fri Jul 30 18:08:34 
EDT 2021

al@test.imagehostplus.com:/usr/obj/usr/src/powerpc.powerpc64/sys/AMIGAX5000 
powerpc
FreeBSD clang version 11.0.0 (git@github.com:llvm/llvm-project.git 
llvmorg-11.0.0-0-g176249bd673)
VT: init without driver.s (2 MiB/s)
cpu0: Freescale e5500 core revision 1.2, 1995.00 MHz
cpu0: Features cc009100<PPC32,PPC64,FPU,MMU,BOOKE,ARCH205,ARCH206>
cpu0: Features2 8000000<ISEL>
cpu0: HID0 c0000000<EMCP,EN_L2MMU_MHD>...
real memory  = 16570585088 (15802 MB)
avail memory = 16520658944 (15755 MB) @0x7fe2efd8
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
arc4random: WARNING: initial seeding bypassed the cryptographic random 
device because it was not yet seeded and the knob 'bypass_before_seedi.
random: entropy device external interfacegehostplus.com)
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree> on nexus0
simplebus0: <Flattened device tree simple bus> on ofwbus0
bman-portals0: <Freescale Buffer Manager - Portals> on ofwbus0
qman-portals0: <Freescale Queue Manager - Portals> on ofwbus0
simplebus1: <Flattened device tree simple bus> mem 
0xffe000000-0xffe000fff on ofwbus0
fman0: <Freescale Frame Manager> mem 0x400000-0x4fffff irq 96,16 on 
simplebus1
> INFO (__ERR_MODULE__) [CPU00, 
/usr/src/sys/contrib/ncsw/Peripherals/FM/fm_ncsw.c:470 
LoadFmanCtrlCode]: FMan-Controller code (ver 101.0.8) .
fman0: Hardware version: 3.0.
rcpm0: <QorIQ Run control and power management> mem 0xe2000-0xe2fff on 
simplebus1
lbc0: <Freescale Local Bus Controller> mem 0xffe124000-0xffe124fff irq 
25 on ofwbus0
pcib0: <Freescale Integrated PCI/PCI-E Controller> mem 
0xffe200000-0xffe200fff irq 16 on ofwbus0
pci0: <OFW PCI bus> on pcib0
pcib1: <MPC85xx Root Complex bridge> irq 16 at device 0.0 numa-domain 0 
on pci0
pci1: <OFW PCI bus> numa-domain 0 on pcib1
pcib2: <Freescale Integrated PCI/PCI-E Controller> mem 
0xffe201000-0xffe201fff irq 16 on ofwbus0
pci2: <OFW PCI bus> on pcib2
pcib3: <MPC85xx Root Complex bridge> irq 16 at device 0.0 numa-domain 0 
on pci2
pci3: <OFW PCI bus> numa-domain 0 on pcib3
pcib4: <PCI-PCI bridge> at device 0.0 numa-domain 0 on pci3
pci4: <PCI bus> numa-domain 0 on pcib4
pcib5: <PCI-PCI bridge> at device 1.0 numa-domain 0 on pci4
pci5: <PCI bus> numa-domain 0 on pcib5
pcib6: <PCI-PCI bridge> irq 5 at device 0.0 numa-domain 0 on pci5
pcib6: allocating 1 bus failed
pcib6: allocating 1 bus failed
pcib6: failed to allocate initial memory window: 0-0xfffff
pcib2: failed to reserve resource for pcib3
pcib6: failed to allocate initial prefetch window: 0-0xfffff
pcib7: <PCI-PCI bridge> at device 2.0 numa-domain 0 on pci4
pci6: <PCI bus> numa-domain 0 on pcib7
pcib8: <PCI-PCI bridge> at device 3.0 numa-domain 0 on pci4
pci7: <PCI bus> numa-domain 0 on pcib8
pcib9: <PCI-PCI bridge> at device 8.0 numa-domain 0 on pci4
pci8: <PCI bus> numa-domain 0 on pcib9
pcib10: <PCI-PCI bridge> at device 16.0 numa-domain 0 on pci4
pci9: <PCI bus> numa-domain 0 on pcib10
gpio0: <Freescale QorIQ GPIO driver> mem 0x130000-0x130fff irq 55 on 
simplebus1
gpiobus0: <GPIO bus> on gpio0
openpic0: <OpenPIC Interrupt Controller> mem 0x40000-0x7ffff on simplebus1
fsl_msi0: <Freescale MSI> mem 0x41600-0x417ff,0x44140-0x44143 irq 
224,225,226,227,228,229,230,231 on simplebus1
fsl_msi1: <Freescale MSI> mem 0x41800-0x419ff,0x45140-0x45143 irq 
232,233,234,235,236,237,238,239 on simplebus1
fsl_msi2: <Freescale MSI> mem 0x41a00-0x41bff,0x46140-0x46143 irq 
240,241,242,243,244,245,246,247 on simplebus1
qman0: <Freescale Queue Manager> mem 0x318000-0x318fff irq 16 on simplebus1
qman0: Hardware version: 1.2.
bman0: <Freescale Buffer Manager> mem 0x31a000-0x31afff irq 16 on 
simplebus1
bman0: Hardware version: 1.0.
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
spi0: <Freescale eSPI controller> mem 0x110000-0x110fff irq 53 on 
simplebus1
spibus0: <OFW SPI bus> on spi0
iichb0: <I2C bus controller> mem 0x118100-0x1181ff irq 38 on simplebus1
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <I2C bus controller> mem 0x119100-0x1191ff irq 39 on simplebus1
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
ds13070: <Microchip MCP7941x RTC> at addr 0xde on iicbus1
pq_mdio0: <Freescale QorIQ MDIO> mem 0xe1120-0xe1fff irq 100 on fman0
dtsec0: <Freescale Data Path Triple Speed Ethernet Controller> mem 
0xe6000-0xe6fff on fman0
dtsec0: Configured for regular mode.
miibus0: <MII bus> on dtsec0
micphy0: <Micrel KSZ9021 10/100/1000 PHY> PHY 3 on miibus0
micphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 
1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
dtsec0: Ethernet address: 00:80:10:fa:ce:01
dtsec1: <Freescale Data Path Triple Speed Ethernet Controller> mem 
0xe8000-0xe8fff on fman0
dtsec1: Configured for regular mode.
miibus1: <MII bus> on dtsec1
micphy1: <Micrel KSZ9021 10/100/1000 PHY> PHY 7 on miibus1
micphy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 
1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
dtsec1: Ethernet address: 00:80:10:fa:ce:02
dtsec2: <Freescale Data Path Triple Speed Ethernet Controller> mem 
0xe0000-0xe0fff on fman0
dtsec2: Could not load local-mac-addr property from DTS
device_attach: dtsec2 attach returned 6
dtsec2: <Freescale Data Path Triple Speed Ethernet Controller> mem 
0xe2000-0xe2fff on fman0
dtsec2: Could not load local-mac-addr property from DTS
device_attach: dtsec2 attach returned 6
pq_mdio1: <Freescale QorIQ MDIO> mem 0xe3120-0xe3fff on fman0
dtsec2: <Freescale Data Path Triple Speed Ethernet Controller> mem 
0xe4000-0xe4fff on fman0
dtsec2: Could not load local-mac-addr property from DTS
device_attach: dtsec2 attach returned 6
pq_mdio2: <Freescale QorIQ MDIO> mem 0xe5120-0xe5fff on fman0
pq_mdio3: <Freescale QorIQ MDIO> mem 0xe7120-0xe7fff on fman0
pq_mdio4: <Freescale QorIQ MDIO> mem 0xe9120-0xe9fff on fman0
dtsec2: <Freescale Data Path Triple Speed Ethernet Controller> mem 
0xf0000-0xf0fff on fman0
dtsec2: Could not load local-mac-addr property from DTS
device_attach: dtsec2 attach returned 6
sdhci_fsl0: <Freescale eSDHC controller> mem 0x114000-0x114fff irq 48 on 
simplebus1
mmc0: <MMC/SD bus> on sdhci_fsl0
iichb2: <I2C bus controller> mem 0x118000-0x1180ff irq 38 on simplebus1
iicbus2: <OFW I2C bus> on iichb2
iic2: <I2C generic I/O> on iicbus2
iichb3: <I2C bus controller> mem 0x119000-0x1190ff irq 39 on simplebus1
iicbus3: <OFW I2C bus> on iichb3
iic3: <I2C generic I/O> on iicbus3
uart0: <16550 or compatible> mem 0x11c500-0x11c5ff irq 36 on simplebus1
uart0: console (115451,n,8,1)
uart1: <16550 or compatible> mem 0x11c600-0x11c6ff irq 36 on simplebus1
uart2: <16550 or compatible> mem 0x11d500-0x11d5ff irq 37 on simplebus1
uart3: <16550 or compatible> mem 0x11d600-0x11d6ff irq 37 on simplebus1
gpioc0: <GPIO controller> on gpio0
ehci0: <Freescale integrated EHCI controller> mem 0x210000-0x210fff irq 
44 on simplebus1
usbus0: EHCI version 1.0
usbus0 on ehci0
ehci1: <Freescale integrated EHCI controller> mem 0x211000-0x211fff irq 
45 on simplebus1
usbus1: EHCI version 1.0
usbus1 on ehci1
fslsata0: <Freescale Integrated SATA Controller> mem 0x220000-0x220fff 
irq 68 on simplebus1
fslsata1: <Freescale Integrated SATA Controller> mem 0x221000-0x221fff 
irq 69 on simplebus1
vgapci0: <VGA-compatible display> at device 0.0 numa-domain 0 on pci1
pci1: <multimedia, HDA> at device 0.1 (no driver attached)
em0: <Intel(R) Gigabit CT 82574L> irq 7 at device 0.0 numa-domain 0 on pci7
em0: Using 1024 TX descriptors and 1024 RX descriptors
em0: Using 2 RX queues 2 TX queues
em0: Using MSI-X interrupts with 3 vectors
em0: Ethernet address: 68:05:ca:24:42:f7
gpiopower0: <GPIO poweroff control> on ofwbus0
gpiopower1: <GPIO restart control> on ofwbus0
Timecounter "timebase" frequency 24937500 Hz quality 1000
Event timer "decrementer" frequency 24937500 Hz quality 1000
Timecounters tick every 1.000 msec
ds13070: registered as a time-of-day clock, resolution 1.000000s
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Freescale EHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Freescale EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on 
usbus0
ugen1.1: <Freescale EHCI root HUB> at usbus1
uhub1 on usbus1
uhub1: <Freescale EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on 
usbus1
uhub0: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered
mmcsd0: 4GB <SDHC USD   0.2 SN 4A9B353D MFG 05/2015 by 116 J`> at mmc0 
49.8MHz/4bit/65535-block
Launching APs: 1
ada0 at fslsata0 bus 0 scbus0 target 0 lun 0
ada0: <SanDisk SSD PLUS 240GB UF5000RL> ACS-2 ATA SATA 3.x device
ada0: Serial Number 191078805013
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 512bytes)
ada0: Command Queueing enabled
ada0: 228944MB (468877312 512 byte sectors)
Trying to mount root from ufs:/dev/ada0s2a [rw]...
random: unblocking device.
ugen0.2: <vendor 0x0424 product 0x2514> at usbus0
uhub2 on uhub0
uhub2: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/b.b3, addr 2> 
on usbus0
uhub2: MTT enabled
ugen1.2: <vendor 0x0424 product 0x2514> at usbus1
uhub3 on uhub1
uhub3: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/b.b3, addr 2> 
on usbus1
uhub3: MTT enabled
uhub2: 4 ports with 4 removable, self powered
uhub3: 4 ports with 4 removable, self powered
ugen0.3: <Hewlett-Packard hp LaserJet 1012> at usbus0
ugen1.3: <vendor 0x04d9 USB Keyboard> at usbus1
ukbd0 on uhub3
ukbd0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/1.01, addr 3> on 
usbus1
kbd1 at ukbd0
ugen1.4: <vendor 0x17ef Lenovo Optical Mouse> at usbus1
ums0 on uhub3
ums0: <vendor 0x17ef Lenovo Optical Mouse, class 0/0, rev 1.10/1.00, 
addr 4> on usbus1
ums0: 3 buttons and [XYZ] coordinates ID=0
ugen0.4: <GeneralPlus USB Audio Device> at usbus0
ugen1.4: <vendor 0x17ef Lenovo Optical Mouse> at usbus1 (disconnected)
ums0: at uhub3, port 2, addr 4 (disconnected)
ums0: detached
ugen1.4: <vendor 0x17ef Lenovo Optical Mouse> at usbus1
ums0 on uhub3
ums0: <vendor 0x17ef Lenovo Optical Mouse, class 0/0, rev 1.10/1.00, 
addr 4> on usbus1
ums0: 3 buttons and [XYZ] coordinates ID=0
ugen1.4: <vendor 0x17ef Lenovo Optical Mouse> at usbus1 (disconnected)
ums0: at uhub3, port 2, addr 4 (disconnected)
ums0: detached
ugen1.4: <vendor 0x17ef Lenovo Optical Mouse> at usbus1
ums0 on uhub3
ums0: <vendor 0x17ef Lenovo Optical Mouse, class 0/0, rev 1.10/1.00, 
addr 4> on usbus1
ums0: 3 buttons and [XYZ] coordinates ID=0
ugen1.4: <vendor 0x17ef Lenovo Optical Mouse> at usbus1 (disconnected)
ums0: at uhub3, port 2, addr 4 (disconnected)
ums0: detached
ugen1.4: <vendor 0x17ef Lenovo Optical Mouse> at usbus1
ums0 on uhub3
ums0: <vendor 0x17ef Lenovo Optical Mouse, class 0/0, rev 1.10/1.00, 
addr 4> on usbus1
ums0: 3 buttons and [XYZ] coordinates ID=0


I believe the issue starts here: scanning bus 0 for devices... ERROR: 
Invalid USB EP length (9)

Also, it goes back up to the top on the screen before loading the 
kernel, so something are written over.

This I believe is with the latest source with git.

I don't know why this is failing.

Here is my kernel config:

#
# Custom kernel for Freescale MPC85XX development boards like the CDS etc.
#
# $FreeBSD: head/sys/powerpc/conf/MPC85XX 277254 2015-01-16 17:41:21Z 
nwhitehorn $
#

ident           AMIGAX5000

include         QORIQ64

#options        BUS_DEBUG
#options        DEBUG
#options        EARLY_PRINTF
#options        MPC85XX_UART_PA=0xffe11c000ull
#options        KTR
#options        KTR_COMPILE=(KTR_PMAP)
#options        KTR_MASK=(KTR_PMAP)
#options        KTR_ENTRIES=8192
#options        KTR_VERBOSE

options         PREEMPTION              # Enable kernel thread preemption
#options         GEOM_PART_EBR           # Extended Boot Records
#options         GEOM_PART_EBR_COMPAT    # Backward compatible partition 
names
options         GEOM_PART_APM           # Apple Partition Maps.
#options         ZFS

device          ukbd
device          ums

# For SAS RAID
#device          pci
#device          aacraid

# For Video
device          vt
device          fbd
device          kbdmux
options         KBD_INSTALL_CDEV

# No Netboot
nooptions       BOOTP
nooptions       BOOTP_NFSROOT

# For Alex
#device         nvme
nooptions       INVARIANTS
nooptions       INVARIANT_SUPPORT
nooptions       WITNESS
nooptions       WITNESS_SKIPSPIN


Please let me know if you need more information. I would really like to 
get past this issue.

Kind Regards,
Al