Re: KHADAS EDGE V booting hangs if I install UEFI instead of u-boot
Date: Thu, 07 Aug 2025 15:38:21 UTC
On Aug 7, 2025, at 08:21, Mario Marietto <marietto2008@gmail.com> wrote:
> Welcome to minicom 2.9
>
> OPTIONS: I18n
> Port /dev/ttyUSB0, 17:17:13
>
> Press CTRL-A Z for help on special keys
Was there any text before the U-Boot SPL message, such
as text showing U-Boot being found and loaded?
I was looking to see all the text from power-on. I'm
not sure if the below is all that text.
(Again, remember thatI've no knowledge of the specific
type of system that you are using.)
> U-Boot SPL 2020.07 (Apr 19 2021 - 09:29:52 +0300)
> Trying to boot from MMC1
>
>
> U-Boot 2020.07 (Apr 19 2021 - 09:29:52 +0300)
>
> SoC: Rockchip rk3399
> Reset cause: POR
> Model: Khadas Edge-V
> DRAM: 3.9 GiB
> PMIC: RK808
> MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
> Loading Environment from SPI Flash... SF: Detected w25q128fw with page size 256 Bytes, erase size 4B
> *** Warning - bad CRC, using default environment
>
> In: serial
> Out: vidconsole
> Err: vidconsole
> Model: Khadas Edge-V
> Net: eth0: ethernet@fe300000
> starting USB...
> Bus usb@fe380000: USB EHCI 1.00
> Bus usb@fe3a0000: USB OHCI 1.0
> Bus usb@fe3c0000: USB EHCI 1.00
> Bus usb@fe3e0000: USB OHCI 1.0
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> scanning bus usb@fe380000 for devices... 1 USB Device(s) found
> scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
> scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
> scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
> ** Unrecognized filesystem type **
I have more notes and questions after the following
block of text. even later: one more note.
> Consoles: EFI console
> Reading loader env vars from /efi/freebsd/loader.env
> Setting currdev to disk0p1:
> FreeBSD/arm64 EFI loader, Revision 1.1
>
> Command line arguments: loader.efi
> Image base: 0xf0dcd000
> EFI version: 2.80
> EFI Firmware: Das U-Boot (rev 8224.1792)
> Console: comconsole (0)
> Load Path: /efi\boot\bootaa64.efi
I'll note that U-Boot here has been configured to provide
UEFI based booting. The above is the FreeBSD loader.efi
in the path and name in the EFI file system in the EFI
partition that it needs to be in in order to be found
and used.
It likely is doin UEFI/DeviceTree instead of UEFI/ACPI.
That brings up the question about our experiment:
Are you after an ACPI based boot? DeviceTree? UEFI
can involve either option.
> Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(1,GPT,c06dc639-cc50-11e)
> Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(1,GPT,c06dc639-cc50-11eb-b8)
> Setting currdev to disk0p1:
> Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(2,GPT,c06dc639-cc50-11eb-b8a0-d)
> Setting currdev to disk0p2:
> Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(3,GPT,c06dc639-cc50-11eb-b8a0-d)
> Setting currdev to disk0p3:
> \
> Loading /boot/defaults/loader.conf
> Loading /boot/defaults/loader.conf
> Loading /boot/device.hints
> Loading /boot/loader.conf
> Loading /boot/loader.conf.local
> cLoading kernel...
> /boot/kernel/kernel text=0x2a8 text=0x7bfa34 text=0x1c9d54 data=0x183ff8 data=0x0+0x384000 syms=[0]/
> Loading configured modules...
> /boot/entropy size=0x1000
> /etc/hostid size=0x25
>
> Hit [Enter] to boot immediately, or any other key for command prompt.
> Booting [/boot/kernel/kernel]...
> Using DTB provided by EFI at 0x80ea000.
The above confirms the UEFI/DeviceTree usage
instead of UEFI/ACPI usage.
>
> EFI framebuffer information:
> addr, size 0xf6000000, 0x7e9000
> dimensions 1920 x 1080
> stride 1920
> masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000
> ---<<BOOT>>---
> KDB: debugger backends: ddb
> KDB: current backend: ddb
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.0-RELEASE-p1 #0: Sun Jun 13 17:07:42 MSK 2021
> root@honeycomb.local:/usr/crochet/work/obj/usr/crochet/src-release-13.0/arm64.aarch64/sys/EXPER4
> FreeBSD clang version 11.0.1 (git@github.com:llvm/llvm-project.git llvmorg-11.0.1-0-g43ff75f2c3fe)
> VT(efifb): resolution 1920x1080
> real memory = 4158345216 (3965 MB)
> avail memory = 4026830848 (3840 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> Starting CPU 4 (100)
> Starting CPU 5 (101)
> FreeBSD/SMP: Multiprocessor System Detected: 6 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP f0f07000 mode 2 pages 1
> MAP f0f0d000 mode 2 pages 2
> MAP f3f30000 mode 2 pages 16
> WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 14.0.
> kbd0 at kbdmux0
> WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 14.0.
> ofwbus0: <Open Firmware Device Tree>
> clk_fixed0: <Fixed clock> on ofwbus0
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> rk_grf0: <RockChip General Register Files> mem 0xff320000-0xff320fff on ofwbus0
> rk3399_pmucru0: <Rockchip RK3399 PMU Clock and Reset Unit> mem 0xff750000-0xff750fff on ofwbus0
> rk3399_cru0: <Rockchip RK3399 Clock and Reset Unit> mem 0xff760000-0xff760fff on ofwbus0
> rk_grf1: <RockChip General Register Files> mem 0xff770000-0xff77ffff on ofwbus0
> clk_fixed1: <Fixed clock> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> regfix3: <Fixed Regulator> on ofwbus0
> regfix4: <Fixed Regulator> on ofwbus0
> regfix5: <Fixed Regulator> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff310000-0xff310fff on ofwbus0
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller v3.0> mem 0xfee00000-0xfee0ffff,0xfef00000-0xfefbffff,0xfff0
> its0: <ARM GIC Interrupt Translation Service> mem 0xfee20000-0xfee3ffff on gic0
> rk_iodomain0: <RockChip IO Voltage Domain> mem 0xff320000-0xff320fff on rk_grf0
> rk_iodomain1: <RockChip IO Voltage Domain> mem 0-0xff76ffff,0-0xffff on rk_grf1
> rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0
> gpio0: <RockChip GPIO Bank controller> mem 0xff720000-0xff7200ff irq 71 on rk_pinctrl0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <RockChip GPIO Bank controller> mem 0xff730000-0xff7300ff irq 72 on rk_pinctrl0
> gpiobus1: <OFW GPIO bus> on gpio1
> gpio2: <RockChip GPIO Bank controller> mem 0xff780000-0xff7800ff irq 73 on rk_pinctrl0
> gpiobus2: <OFW GPIO bus> on gpio2
> gpio3: <RockChip GPIO Bank controller> mem 0xff788000-0xff7880ff irq 74 on rk_pinctrl0
> gpiobus3: <OFW GPIO bus> on gpio3
> gpio4: <RockChip GPIO Bank controller> mem 0xff790000-0xff7900ff irq 75 on rk_pinctrl0
> gpiobus4: <OFW GPIO bus> on gpio4
> rk_i2c0: <RockChip I2C> mem 0xff130000-0xff130fff irq 22 on ofwbus0
> iicbus0: <OFW I2C bus> on rk_i2c0
> rk_i2c1: <RockChip I2C> mem 0xff3d0000-0xff3d0fff irq 39 on ofwbus0
> iicbus1: <OFW I2C bus> on rk_i2c1
> syr8270: <Silergy SYR827 regulator> at addr 0x80 on iicbus1
> rk_i2c2: <RockChip I2C> mem 0xff3e0000-0xff3e0fff irq 40 on ofwbus0
> iicbus2: <OFW I2C bus> on rk_i2c2
> rk80x_pmu0: <RockChip RK808 PMIC> at addr 0x36 irq 76 on iicbus1
> rk80x_pmu0: registered as a time-of-day clock, resolution 1.000000s
> generic_timer0: <ARMv8 Generic Timer> irq 2,3,4,5 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
> Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
> rk_tsadc0: <RockChip temperature sensors> mem 0xff260000-0xff2600ff irq 35 on ofwbus0
> rk_usb2phy0: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
> rk_usb2phy1: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
> rk_emmcphy0: <Rockchip RK3399 eMMC PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
> rk_pcie_phy0: <Rockchip RK3399 PCIe PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
> rk_typec_phy0: <Rockchip RK3399 PHY TYPEC> mem 0xff7c0000-0xff7fffff on ofwbus0
> rk_typec_phy1: <Rockchip RK3399 PHY TYPEC> mem 0xff800000-0xff83ffff on ofwbus0
> cpulist0: <Open Firmware CPU Group> on ofwbus0
> cpu0: <Open Firmware CPU> on cpulist0
> cpufreq_dt0: <Generic cpufreq driver> on cpu0
> cpu1: <Open Firmware CPU> on cpulist0
> cpufreq_dt1: <Generic cpufreq driver> on cpu1
> cpu2: <Open Firmware CPU> on cpulist0
> cpufreq_dt2: <Generic cpufreq driver> on cpu2
> cpu3: <Open Firmware CPU> on cpulist0
> cpufreq_dt3: <Generic cpufreq driver> on cpu3
> cpu4: <Open Firmware CPU> on cpulist0
> cpufreq_dt4: <Generic cpufreq driver> on cpu4
> cpu5: <Open Firmware CPU> on cpulist0
> cpufreq_dt5: <Generic cpufreq driver> on cpu5
> pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
> pmu1: <Performance Monitoring Unit> irq 1 on ofwbus0
> pcib0: <Rockchip PCIe controller> mem 0xf8000000-0xf9ffffff,0xfd000000-0xfdffffff irq 6,7,8 on ofwb0
> pcib0: Gen1 link training timeouted: 0x00080001.
> pci0: <PCI bus> on pcib0
> pcib1: <PCI-PCI bridge> at device 0.0 on pci0
> pcib0: failed to reserve resource for pcib1
> pcib1: failed to allocate initial memory window: 0-0xfffff
> pci1: <PCI bus> on pcib1
> dwc0: <Rockchip Gigabit Ethernet Controller> mem 0xfe300000-0xfe30ffff irq 9 on ofwbus0
> miibus0: <MII bus> on dwc0
> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0
> rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-mastero
> rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
> rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-mastero
> dwc0: Ethernet address: 62:43:94:13:10:0c
> rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe310000-0xf0
> rockchip_dwmmc0: Hardware version ID is 270a
> rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe320000-0xf0
> rockchip_dwmmc1: Hardware version ID is 270a
> mmc0: <MMC/SD bus> on rockchip_dwmmc1
> sdhci_fdt0: <Rockchip RK3399 fdt SDHCI controller> mem 0xfe330000-0xfe33ffff irq 12 on ofwbus0
> rk_emmcphy0: got emmcclk clock
> sdhci_fdt0-slot0: Hardware doesn't specify timeout clock frequency, setting BROKEN_TIMEOUT quirk.
> sdhci_fdt0: 1 slot(s) allocated
> mmc1: <MMC/SD bus> on sdhci_fdt0
> ehci0: <Generic EHCI Controller> mem 0xfe380000-0xfe39ffff irq 13 on ofwbus0
> usbus0: EHCI version 1.0
> usbus0 on ehci0
> ohci0: <Generic OHCI Controller> mem 0xfe3a0000-0xfe3bffff irq 14 on ofwbus0
> usbus1 on ohci0
> ehci1: <Generic EHCI Controller> mem 0xfe3c0000-0xfe3dffff irq 15 on ofwbus0
> usbus2: EHCI version 1.0
> usbus2 on ehci1
> ohci1: <Generic OHCI Controller> mem 0xfe3e0000-0xfe3fffff irq 16 on ofwbus0
> usbus3 on ohci1
> rk_dwc30: <Rockchip RK3399 DWC3> on ofwbus0
> xhci0: Only host mode is supported
> xhci0: Only host mode is supported
> rk_dwc31: <Rockchip RK3399 DWC3> on ofwbus0
> xhci0: <Synopsys Designware DWC3> mem 0xfe900000-0xfe9fffff irq 78 on rk_dwc31
> xhci0: 64 bytes context size, 32-bit DMA
> usbus4: trying to attach
> usbus4 on xhci0
> iic0: <I2C generic I/O> on iicbus0
> uart0: <16750 or compatible> mem 0xff180000-0xff1800ff irq 26 on ofwbus0
> uart1: <16750 or compatible> mem 0xff1a0000-0xff1a00ff irq 28 on ofwbus0
> uart1: console (1500000,n,8,1)
> iicbus1: <unknown card> at addr 0x82
> iic1: <I2C generic I/O> on iicbus1
> iic2: <I2C generic I/O> on iicbus2
> pwm0: <Rockchip PWM> mem 0xff420000-0xff42000f on ofwbus0
> pwmbus0: <OFW PWM bus> on pwm0
> pwmc0: <PWM Control> channel 0 on pwmbus0
> pwm1: <Rockchip PWM> mem 0xff420020-0xff42002f on ofwbus0
> pwmbus1: <OFW PWM bus> on pwm1
> pwmc1: <PWM Control> channel 0 on pwmbus1
> i2s0: <Rockchip I2S> mem 0xff880000-0xff880fff irq 51 on ofwbus0
> Cannot set frequency for clk: clkin_i2s, error: 34
> Cannot set frequency for clk: xin24m, error: 34
> i2s1: <Rockchip I2S> mem 0xff890000-0xff890fff irq 52 on ofwbus0
> Cannot set frequency for clk: clkin_i2s, error: 34
> Cannot set frequency for clk: xin24m, error: 34
> i2s2: <Rockchip I2S> mem 0xff8a0000-0xff8a0fff irq 53 on ofwbus0
> Cannot set frequency for clk: clkin_i2s, error: 34
> Cannot set frequency for clk: xin24m, error: 34
> pcm0: <simple-audio-card> on ofwbus0
> hdmiaudio0: <Rockchip HDMI Audio Hack> mem 0xff940000-0xff95ffff irq 60 on ofwbus0
> gpioc0: <GPIO controller> on gpio0
> gpioc1: <GPIO controller> on gpio1
> gpioc2: <GPIO controller> on gpio2
> gpioc3: <GPIO controller> on gpio3
> gpioc4: <GPIO controller> on gpio4
> gpioled0: <GPIO LEDs> on ofwbus0
> cryptosoft0: <software crypto>
> Timecounters tick every 1.000 msec
> usbus0: 480Mbps High Speed USB v2.0
> usbus1: 12Mbps Full Speed USB v1.0
> ugen0.1: <Generic EHCI root HUB> at usbus0
> uhub0 on usbus0
> uhub0: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
> ugen1.1: <Generic OHCI root HUB> at usbus1
> uhub1 on usbus1
> uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> usbus2: 480Mbps High Speed USB v2.0
> usbus3: 12Mbps Full Speed USB v1.0
> ugen2.1: <Generic EHCI root HUB> at usbus2
> uhub2 on usbus2
> uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
> ugen3.1: <Generic OHCI root HUB> at usbus3
> uhub3 on usbus3
> uhub3: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
> usbus4: 5.0Gbps Super Speed USB v3.0
> uhub1: 1 port with 1 removable, self powered
> ugen4.1: <Synopsys XHCI root HUB> at usbus4
> uhub4 on usbus4
> uhub4: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus4
> mmcsd0: 128GB <SDHC SD128 8.5 SN B7E83B69 MFG 10/2020 by 3 SD> at mmc0 50.0MHz/4bit/1021-block
> uhub3: 1 port with 1 removable, self powered
> mmcsd1: 31GB <MMCHC BJTD4R 0.9 SN F84B4A79 MFG 11/2022 by 21 0x0000> at mmc1 49.5MHz/8bit/65535-blok
> mmcsd1boot0: 4MB partition 1 at mmcsd1
> mmcsd1boot1: 4MB partition 2 at mmcsd1
> mmcsd1rpmb: 4MB partition 3 at mmcsd1
> pcm0: failed to set sysclk for codec node
> pcm0: failed to set sysclk for codec node
> pcm0: failed to set sysclk for codec node
> pcm0: failed to set sysclk for codec node
> Release APs...done
> CPU 0: ARM Cortex-A53 r0p4 affinity: 0 0
> Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64>
> Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
> Instruction Set Attributes 1 = <>
> Processor Features 0 = <GIC,AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
> Processor Features 1 = <>
> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
> Memory Model Features 1 = <8bit VMID>
> Memory Model Features 2 = <32bit CCIDX,48bit VA>
> Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
> Debug Features 1 = <>
> Auxiliary Features 0 = <>
> Auxiliary Features 1 = <>
> CPU 1: ARM Cortex-A53 r0p4 affinity: 0 1
> Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64>
> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
> CPU 2: ARM Cortex-A53 r0p4 affinity: 0 2
> Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64>
> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
> CPU 3: ARM Cortex-A53 r0p4 affinity: 0 3
> Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64>
> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
> CPU 4: ARM Cortex-A72 r0p2 affinity: 1 0
> Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64>
> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA>
> CPU 5: ARM Cortex-A72 r0p2 affinity: 1 1
> Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64>
> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA>
> uhub0: 1 port with 1 removable, self powered
> Trying to mount root from ufs:/dev/gpt/install [rw,noatime]...
> GEOM: mmcsd1: the primary GPT table is corrupt or invalid.
> uhub4: 2 ports with 2 removable, self powered
> GEOM: mmcsd1: using the secondary instead -- recovery strongly advised.
> uhub2: 1 port with 1 removable, self powered
> Dual Console: Serial Primary, Video Secondary
> Setting hostuuid: 65386165-6635-6336-3035-383363623236.
> Setting hostid: 0x1a119174.
> Solaris: WARNING: ignoring tunable zfs_arc_max (using 0 instead)
> Solaris: WARNING: ignoring tunable zfs_arc_max (using 3056451584 instead)
> ZFS filesystem version: 5
> ZFS storage pool version: features support (5000)
> Starting file system checks:
> /dev/gpt/install: FILE SYSTEM CLEAN; SKIPPING CHECKS
> /dev/gpt/install: clean, 17191348 free (11716 frags, 2147454 blocks, 0.0% fragmentation)
> Mounting local filesystems:.
> ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/loca4
> Setting hostname: khadas-edge.
> Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTD
> Feeding entropy: .
> Autoloading module: dwwdt.ko
> dwwdt0: <Synopsys Designware watchdog timer> mem 0xff848000-0xff8480ff irq 48 on ofwbus0
> xhci1: Only host mode is supported
> lo0: link state changed to UP
> dwc0: link state changed to DOWN
> Starting Network: lo0 dwc0.
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
> options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
> inet6 ::1 prefixlen 128
> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
> inet 127.0.0.1 netmask 0xff000000
> groups: lo
> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
> dwc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
> options=8000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE>
> ether 62:43:94:13:10:0c
> media: Ethernet autoselect (none)
> status: no carrier
> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
> Starting devd.
> Autoloading module: dwwdt.ko
> add host 127.0.0.1: gateway lo0 fib 0: route already in table
> add host ::1: gateway lo0 fib 0: route already in table
> add net fe80::: gateway ::1
> add net ff02::: gateway ::1
> add net ::ffff:0.0.0.0: gateway ::1
> add net ::0.0.0.0: gateway ::1
> Waiting 5s for the default route interface: ....
> Clearing /tmp (X related).
> Creating and/or trimming log files.
> Updating motd:.
> Updating /var/run/os-release done.
> Starting syslogd.
> Starting pwmfan.
> Mounting late filesystems:.
> Starting powerd.
> Security policy loaded: MAC/ntpd (mac_ntpd)
> Starting ntpd.
> Starting dbus.
> Starting local daemons:.
> Jan 21 08:50:56 khadas-edge ntpd[981]: error resolving pool 0.freebsd.pool.ntp.org: Name does not r)
> Configuring vt: keymap blanktime.
> Starting cron.
> Performing sanity check on sshd configuration.
> Starting sshd.
> Starting background file system checks in 60 seconds.
>
> Mon Jan 21 08:51:03 UTC 2013
>
> FreeBSD/arm64 (khadas-edge) (ttyu1)
>
> login:
>
>
>
> On Thu, Aug 7, 2025 at 4:26 PM Mark Millard <marklmi@yahoo.com> wrote:
> A question:
>
> Can you set up a working U-Boot based boot, capture
> all the output, and report it to the list?
>
> That would give something to compare/contrast with
> for the messages that have been reported so far.
>
===
Mark Millard
marklmi at yahoo.com