Re: KHADAS EDGE V booting hangs if I install UEFI instead of u-boot

On Aug 5, 2025, at 20:04, Mario Marietto <marietto2008@gmail.com> wrote:

> Hello.
> Finally I’ve been able to setup a serial connection with the board with the goal to understand why the KHADAS EDGE V does not boot FreeBSD if I make the installation of UEFI instead of u-boot and I’ve gathered these log messages :

I only have a basic type note here:

What you show below references "uboot" as something
being loaded.

> Boot1: 2018-08-06, version: 1.15 
> CPUId = 0x0 
> ChipType = 0x10, 218 
> SdmmcInit=2 0 
> BootCapSize=100000
> UserCapSize=29820MB
> FwPartOffset=2000 , 100000
> mmc0:cmd5,20
> SdmmcInit=0 0
> BootCapSize=0
> UserCapSize=121942MB
> FwPartOffset=2000 , 0 
> run on sd0 
> StorageInit ok = 89823 
> SecureMode = 0 
> SecureInit read PBA: 0x4 
> SecureInit read PBA: 0x404 
> SecureInit read PBA: 0x804 
> SecureInit read PBA: 0xc04 
> SecureInit read PBA: 0x1004 
> SecureInit read PBA: 0x1404 
> SecureInit read PBA: 0x1804 
> SecureInit read PBA: 0x1c04 
> SecureInit ret = 0, SecureMode = 0 
> GPT 0x3190d20 signature is wrong 
> LoadTrust Addr:0x4000 
> No find bl30.bin 
> No find bl32.bin 
> Load uboot, ReadLba = 2000

Note the "uboot" above. Seems to be loading a U-Boot.

> Load OK, addr=0x200000, size=0xf0000

Note that the "uboot" loaded OK.

> 
> RunBL31 0x10000 
> NOTICE: BL31: v1.3(debug):51f2096 
> NOTICE: BL31: Built : 16:24:31, May 6 2019 
> NOTICE: BL31: Rockchip release version: v1.1 
> INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 
> INFO: Using opteed sec cpu_context! 
> INFO: boot cpu mask: 0 
> INFO: plat_rockchip_pmu_init(1181): pd status 3e 
> INFO: BL31: Initializing runtime services 
> WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s dK
> ERROR: Error initializing runtime service opteed_fast 
> INFO: BL31: Preparing for EL3 exit to normal world 
> INFO: Entry point address = 0x200000 
> INFO: SPSR = 0x3c9 
> PLL at FF750000: fbdiv=112, refdiv=2, postdiv1=2, postdiv2=1, vco=1344000 khz, output=672000 khz 
> Boot PLLs: 
> APLLL = 400000000 
> APLLB = 24000000 
> CPLL = 24000000 
> DPLL = 800000000 
> GPLL = 400000000 
> NPLL = 24000000 
> VPLL = 24000000 
> PLL at FF760000: fbdiv=68, refdiv=1, postdiv1=2, postdiv2=1, vco=1632000 khz, output=816000 khz 
> PLL at FF760020: fbdiv=68, refdiv=1, postdiv1=2, postdiv2=1, vco=1632000 khz, output=816000 khz 
> PLL at FF760080: fbdiv=100, refdiv=1, postdiv1=3, postdiv2=1, vco=2400000 khz, output=800000 khz 
> PLL at FF7600A0: fbdiv=125, refdiv=1, postdiv1=3, postdiv2=1, vco=3000000 khz, output=1000000 khz 
> PLL at FF760060: fbdiv=100, refdiv=1, postdiv1=3, postdiv2=1, vco=2400000 khz, output=800000 khz 
> After clock init: 
> APLLL = 816000000 
> APLLB = 816000000 
> CPLL = 800000000 
> DPLL = 800000000 
> GPLL = 800000000 
> NPLL = 1000000000 
> VPLL = 24000000 
> PLL at FF760000: fbdiv=54, refdiv=1, postdiv1=1, postdiv2=1, vco=1296000 khz, output=1296000 khz 
> PLL at FF760020: fbdiv=70, refdiv=1, postdiv1=1, postdiv2=1, vco=1680000 khz, output=1680000 khz
> �������� : FROZEN : No more messages.
> 
> 
> it’s not clear why it hangs. Do you have a vague idea why it hangs there ?
> And more important,do you know where / to whom I can ask ?
> Don't suggest to me the KHADAS forum. I detected a low quality of help for the newbies if they have complicated problems to solve.
> Their help is good only for the business users. I'm not.
> Thanks.

I do not see any evidence above that UEFI was involved.
(But I've never dealt with a KHADAS EDGE V.)

Looks like an attempted "uboot" based boot to me.

You may need to give a lot more detail about how you
have things set up, possibly for both a working U-Boot
(if you have such a context) and for what you did to
configure for UEFI, providing for a compare/contrast
inspection.

I have no clue what you installed that was a UEFI
or where/how it was installed or how the system was
told to try to put it to use.

But, again, I've no knowledge of the specific type
of context that you have so my notes are very limited.

===
Mark Millard
marklmi at yahoo.com