Re: u-boot debug, was: Re: U-boot on RPI3, sees disk but won't boot it

Reply: Mark Millard : "Re: u-boot debug, was: Re: U-boot on RPI3, sees disk but won't boot it"
In reply to: Mark Millard : "Re: u-boot debug, was: Re: U-boot on RPI3, sees disk but won't boot it"
Go to: [ bottom of page ] [ top of archives ] [ this month ]

From: bob prohaska <fbsd_at_www.zefox.net>
Date: Wed, 28 Sep 2022 04:51:45 UTC

On Tue, Sep 27, 2022 at 07:25:09PM -0700, Mark Millard wrote:
> 
> Beyond enable_uart=1 there is, quoting from:
[snip] 
> "uart_2ndstage=1" 
Also added to config.txt

> 
> For the current purposes, dtdebug=1 probably does
> not provide anything of interest. But it is
> available to enable as well.

Added to config.txt as well. 

In general there isn't much additional output from u-boot. 
On a successful try I see what begins as (I think) bootcode.bin output:
.....
MESS:00:00:24.909927:0: Device tree loaded to 0x4000 (size 0x7374)
MESS:00:00:24.918100:0: uart: Set PL011 baud rate to 103448.300000 Hz
MESS:00:00:24.924351:0: uart: Baud rate change done...
MESS:00:00:24.927765:0: uart: Baud rate change done...

Next u-boot takes over

U-Boot 2022.04 (Sep 27 2022 - 20:04:31 -0700)

DRAM:  948 MiB
RPI 3 Model B (0xa02082)
Core:  69 devices, 10 uclasses, devicetree: board
MMC:   mmc@7e300000: 2
Loading Environment from FAT... In:    serial
Out:   vidconsole
Err:   vidconsole
Net:   No ethernet found.
starting USB...
Bus usb@7e980000: USB DWC2
scanning bus usb@7e980000 for devices... 6 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot:  0 
MMC Device 0 not found
no mmc device at slot 0
MMC Device 1 not found
no mmc device at slot 1
Card did not respond to voltage select! : -110

Device 0: Vendor: SABRENT  Rev: 1214 Prod: 
            Type: Hard Disk
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
... is now current device
Scanning usb 0:1...
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Card did not respond to voltage select! : -110
Scanning disk mmc@7e300000.blk...
Disk mmc@7e300000.blk not ready
Scanning disk usb_mass_storage.lun0...
Found 3 disks
Missing RNG device for EFI_RNG_PROTOCOL
No EFI system partition
BootOrder not defined
EFI boot manager: Cannot load any image
Found EFI removable media binary efi/boot/bootaa64.efi
1262604 bytes read in 38 ms (31.7 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Booting /efi\boot\bootaa64.efi

But, that's it. Is that what one would expect? 

Failed attempts are more terse:

U-Boot 2022.04 (Sep 27 2022 - 20:04:31 -0700)

DRAM:  948 MiB
RPI 3 Model B (0xa02082)
Core:  69 devices, 10 uclasses, devicetree: board
MMC:   mmc@7e300000: 2
Loading Environment from FAT... In:    serial
Out:   vidconsole
Err:   vidconsole
Net:   No ethernet found.
starting USB...
Bus usb@7e980000: USB DWC2
scanning bus usb@7e980000 for devices... 6 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0 
MMC Device 0 not found
no mmc device at slot 0
MMC Device 1 not found
no mmc device at slot 1
Card did not respond to voltage select! : -110

Device 0: unknown device
Waiting for Ethernet connection... done. 

I imagined u-boot would be more talkative,
similar to the MESS..... output from bootcode.bin

The output from make reports
===>  Applying extra patch patches for u-boot-rpi-arm64-2022.04_1 from /usr/ports/sysutils/u-boot-rpi-arm64/files/
No such line 209 in input file, ignoring

Strangely, it doesn't report which patch didn't work.
The directory contains
patch-common_usb.c        patch-common_usb__storage.c  patch-lib_efi__loader_efi__console.c
patch-common_usb__hub.c   patch-include_configs_rpi.h  rpi_arm64_fragment

No idea whether it matters. 
 
Thanks for reading,

bob prohaska