Booting MOCHAbin-5g Marvell board from GlobalscaleTech
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Fri, 11 Mar 2022 05:02:13 UTC
I loaded the FreeBSD 13.0 (and also tried 14.0-current snapshot) on a
USB stick and tried to boot it on the new MOCHAbin-5g.
https://globalscaletechnologies.com/product/mochabin/ It paniced booting
the EFI file. Any ideas what to try next? Marvell>> usb start starting
USB... USB0: Register 2000120 NbrPorts 2 Starting the controller USB
XHCI 1.00 USB1: Register 2000120 NbrPorts 2 Starting the controller USB
XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning
bus 1 for devices... 5 USB Device(s) found scanning usb for storage
devices... 1 Storage Device(s) found
Marvell>> fatload usb 0 0x6000000 EFI/BOOT/bootaa64.efi
1259212 bytes read in 59 ms (20.4 MiB/s) Marvell>> bootefi 0x6000000
## Starting EFI application at 06000000 ...
WARNING: using memory device/image path, this may confuse some payloads!
Scanning disksdhci@6e0000.blk...
Scanning disk usb_mass_storage.lun0...
Found 5 disks
"Synchronous Abort" handler, esr 0x96000046
elr: 0000000000063728 lr : 000000000005b51c (reloc)
elr: 000000007ff9c728 lr : 000000007ff9451c
x0 : 00000000bffff000 x1 : 0000000000000000
x2 : 000000000000001f x3 : 00000000bffff018
x4 : 00000000bffff008 x5 : 0000000000000000
x6 : 0000000000000003 x7 : 00000000bffff020
x8 : 000000007f900000 x9 : 0000000000000008
x10: 0000000000000006 x11: 0000000000000006
x12: 000000000001869f x13: 0000000000000003
x14: 0000000000000000 x15: 00000000ffffffff
x16: 0000000000000000 x17: 0000000000000001
x18: 000000007f628dd0 x19: 00000000bffff000
x20: 000000007e624040 x21: 000000007e624040
x22: 0000000006000000 x23: 0000000000000000
x24: 000000007f624bc0 x25: 000000007ffa4000
x26: 0000000000000000 x27: 0000000000000000
x28: 000000007f717870 x29: 000000007f624b60
Resetting CPU ...
resetting ...
BootROM - 2.03
Starting CP-0 IOROM 1.07
Booting from SPI NOR flash 1 (0x32)
Found valid image at boot postion 0x000
lmv_ddr: mv_ddr-devel-18.12.0-g2e20f5d (Dec 30 2021 - 16:08:48)
mv_ddr: scrubbing memory...
mv_ddr: completed successfully
llBL2: Initiating SCP_BL2 transfer to SCP
ll
U-Boot 2018.03-devel-18.12.3-ga49bd540df (Dec 30 2021 - 16:06:18 +0800)
Model: Marvell Armada 7040 Mochabin development board
SoC: Armada7040-B0; AP806-B0; CP115-A0
Clock: CPU 1400 [MHz]
DDR 800 [MHz]
FABRIC 800 [MHz]
MSS 200 [MHz]
LLC Enabled (Exclusive Mode)
DRAM: 8 GiB
Bus spi@700680 CS0 configured for direct access 00000000f9000000:0x1000000
SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB
EEPROM configuration pattern not detected.
Comphy chip #0:
Comphy-0: SGMII1 3.125 Gbps
Comphy-1: USB3_HOST0
Comphy-2: SATA0
Comphy-3: SATA1
Comphy-4: SFI0 10.3125 Gbps
Comphy-5: PEX2
UTMI PHY 0 initialized to USB Host0
UTMI PHY 1 initialized to USB Host1
SATA link 0 timeout.
SATA link 1 timeout.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq led only pmp fbss pio slum part sxs
PCIE-0: Link up (Gen1-x1, Bus0)
MMC: sdhci@6e0000: 0
Loading Environment from SPI Flash... OK
Model: Marvell Armada 7040 Mochabin development board
Net: eth0: mvpp2-0 [PRIME], eth1: mvpp2-1, eth2: mvpp2-2
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> help
? - alias for 'help'
avs - Set/Get Adaptive Voltage Scaling (AVS) value
base - print or set address offset
bdinfo - print Board Info structure
blkcache- block cache diagnostics and control
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootefi - Boots an EFI payload from memory
bootelf - Boot from an ELF image in memory
booti - boot arm64 Linux Image image from memory
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bubt - Burn a u-boot image to flash
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dcache - enable or disable data cache
dhcp - boot image via network using DHCP/TFTP protocol
dm - Driver model low level access
echo - echo args to console
editenv - edit environment variable
env - environment handling commands
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
ext4load- load binary file from a Ext4 filesystem
ext4ls - list files in a directory (default /)
ext4size- determine a file's size
ext4write- create a file in the root directory
false - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fatsize - determine a file's size
fdt - flattened device tree utility commands
fstype - Look up a filesystem type
go - start application at address 'addr'
gpio - query and control gpio pins
gzwrite - unzip and write memory to block device
help - print command description/usage
hw_info - hw_info
i2c - I2C sub-system
icache - enable or disable instruction cache
iminfo - print header information for application image
imxtract- extract a part of a multi-image
ir - ir - Reading and changing internal register values.
itest - return true/false on integer compare
led - manage LEDs
load - load binary file from a filesystem
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
ls - list files in a directory (default /)
lzmadec - lzma uncompress a memory region
map - Display address decode windows
md - memory display
mdio - MDIO utility commands
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - display MMC info
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
part - disk partition related commands
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
pxe - commands to get and boot from pxe files
regulator- uclass operations
reset - Perform RESET of the CPU
run - run commands in an environment variable
rx_training- rx_training <cp id> <comphy id>
save - save file to a filesystem
saveenv - save environment variables to persistent storage
scsi - SCSI sub-system
scsiboot- boot from SCSI device
setenv - set environment variables
setexpr - set environment variable as the result of eval expression
sf - SPI flash sub-system
showvar - print local hushshell variables
size - determine a file's size
sleep - delay execution for some time
source - run script from memory
sspi - SPI utility command
switch - Switch Access commands
sysboot - command to get and boot from syslinux files
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
time - run commands and summarize execution time
true - do nothing, successfully
tsen - tsen - Display the SoC temperature.
unzip - unzip a memory region
usb - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
Marvell>>
Marvell>> printenv
arch=arm
baudrate=115200
board=mvebu_armada-8k
board_name=mvebu_armada-8k
bootcmd=ev 0; ext4load mmc 0:1 $kernel_addr_r $image_name; ext4load mmc 0:1 $fdt_addr_r $fdt_name; setenv bootargs $console root=PARTUUID=89708921-01 rw rootwait net.ifnames=0 biosdevname=0; booti $kernel_addr_r - $fdt_addr_r
bootdelay=2
console=console=ttyS0,115200 earlycon=uart8250,mmio32,0xf0512000
cpu=armv8
eth1addr=00:51:82:11:22:01
eth2addr=00:51:82:11:22:02
ethact=mvpp2-0
ethaddr=00:51:82:11:22:00
ethprime=eth0
extra_params=pci=pcie_bus_safe
fdt_addr_r=0x6f00000
fdt_high=0xffffffffffffffff
fdt_name=boot/armada-7040-mochabin.dtb
fdtcontroladdr=7f625230
gatewayip=10.4.50.254
get_images=tftpboot $kernel_addr_r $image_name; tftpboot $fdt_addr_r $fdt_name; run get_ramfs
get_ramfs=if test "${ramfs_name}" != "-"; then setenv ramdisk_addr_r 0x8000000; tftpboot $ramdisk_addr_r $ramfs_name; else setenv ramdisk_addr_r -;fi
hostname=marvell
image_name=boot/Image
initrd_addr=0xa00000
initrd_size=0x2000000
ipaddr=0.0.0.0
kernel_addr_r=0x7000000
loadaddr=0x6000000
netdev=eth0
netmask=255.255.255.0
ramdisk_addr_r=0x8000000
ramfs_name=-
root=root=/dev/nfs rw
rootpath=/srv/nfs/
serverip=0.0.0.0
set_bootargs=setenv bootargs $console $root ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:none nfsroot=$serverip:$rootpath,tcp,v3 $extra_params $cpuidle
soc=mvebu
stderr=serial@512000
stdin=serial@512000
stdout=serial@512000
vendor=Marvell
Environment size: 1511/65532 bytes
Marvell>> help bootefi
bootefi - Boots an EFI payload from memory
Usage:
bootefi <image address> [fdt address]
- boot EFI payload stored at address <image address>.
If specified, the device tree located at <fdt address> gets
exposed as EFI configuration table.
bootefi bootmgr [fdt addr]
- load and boot EFI payload based on BootOrder/BootXXXX variables.
If specified, the device tree located at <fdt address> gets
exposed as EFI configuration table.
Marvell>> help usbboot
usbboot - boot from USB device
Usage:
usbboot loadAddr dev:part
Marvell>> usb storage
Device 0: Vendor: Monster Rev: PMAP Prod: MONSTER DIGITAL
Type: Removable Hard Disk
Capacity: 59082.0 MB = 57.6 GB (120999936 x 512)