git: f25b0d6dd75d - main - UART: Remove ingenic xburst (mips) code from ns8250 driver

The branch main has been updated by oh:

URL: https://cgit.FreeBSD.org/src/commit/?id=f25b0d6dd75d41cbb27d1cc40bb53185672281e0

commit f25b0d6dd75d41cbb27d1cc40bb53185672281e0
Author:     Oskar Holmlund <oh@FreeBSD.org>
AuthorDate: 2023-11-08 08:03:55 +0000
Commit:     Oskar Holmlund <oh@FreeBSD.org>
CommitDate: 2023-11-08 08:03:55 +0000

    UART: Remove ingenic xburst (mips) code from ns8250 driver
    
    Since ingenic JZ4780 SOC support has been removed there is no need
    to support ingenic quirks in the UART driver.
    Invert of commit b192bae67ea835b7e431225bad375b5d5fe4297f
    
    Reviewed by:    imp, manu
    Approved by:    imp, manu (mentor)
    Differential Revision:  https://reviews.freebsd.org/D42497
---
 sys/dev/ic/ns16550.h           |  3 ---
 sys/dev/uart/uart_dev_ns8250.c | 43 ++++++------------------------------------
 2 files changed, 6 insertions(+), 40 deletions(-)

diff --git a/sys/dev/ic/ns16550.h b/sys/dev/ic/ns16550.h
index 76a680a410b9..290a55ca7346 100644
--- a/sys/dev/ic/ns16550.h
+++ b/sys/dev/ic/ns16550.h
@@ -162,9 +162,6 @@
 #define	FIFO_XMT_RST	FCR_XMT_RST
 #define	FCR_DMA		0x08
 #define	FIFO_DMA_MODE	FCR_DMA
-#ifdef CPU_XBURST
-#define	FCR_UART_ON	0x10
-#endif
 #define	FCR_RX_LOW	0x00
 #define	FIFO_RX_LOW	FCR_RX_LOW
 #define	FCR_RX_MEDL	0x40
diff --git a/sys/dev/uart/uart_dev_ns8250.c b/sys/dev/uart/uart_dev_ns8250.c
index 3787c6ed4c9b..96062fe759d3 100644
--- a/sys/dev/uart/uart_dev_ns8250.c
+++ b/sys/dev/uart/uart_dev_ns8250.c
@@ -233,9 +233,6 @@ ns8250_flush(struct uart_bas *bas, int what)
 	int drain = 0;
 
 	fcr = FCR_ENABLE;
-#ifdef CPU_XBURST
-	fcr |= FCR_UART_ON;
-#endif
 	if (what & UART_FLUSH_TRANSMITTER)
 		fcr |= FCR_XMT_RST;
 	if (what & UART_FLUSH_RECEIVER)
@@ -327,10 +324,6 @@ ns8250_probe(struct uart_bas *bas)
 {
 	u_char val;
 
-#ifdef CPU_XBURST
-	uart_setreg(bas, REG_FCR, FCR_UART_ON);
-#endif
-
 	/* Check known 0 bits that don't depend on DLAB. */
 	val = uart_getreg(bas, REG_IIR);
 	if (val & 0x30)
@@ -352,7 +345,7 @@ static void
 ns8250_init(struct uart_bas *bas, int baudrate, int databits, int stopbits,
     int parity)
 {
-	u_char ier, val;
+	u_char ier;
 
 	if (bas->rclk == 0)
 		bas->rclk = DEFAULT_RCLK;
@@ -369,11 +362,7 @@ ns8250_init(struct uart_bas *bas, int baudrate, int databits, int stopbits,
 	uart_barrier(bas);
 
 	/* Disable the FIFO (if present). */
-	val = 0;
-#ifdef CPU_XBURST
-	val |= FCR_UART_ON;
-#endif
-	uart_setreg(bas, REG_FCR, val);
+	uart_setreg(bas, REG_FCR, 0);
 	uart_barrier(bas);
 
 	/* Set RTS & DTR. */
@@ -552,9 +541,6 @@ ns8250_bus_attach(struct uart_softc *sc)
 	ns8250->busy_detect = bas->busy_detect;
 	ns8250->mcr = uart_getreg(bas, REG_MCR);
 	ns8250->fcr = FCR_ENABLE;
-#ifdef CPU_XBURST
-	ns8250->fcr |= FCR_UART_ON;
-#endif
 	if (!resource_int_value("uart", device_get_unit(sc->sc_dev), "flags",
 	    &ivar)) {
 		if (UART_FLAGS_FCR_RX_LOW(ivar))
@@ -847,7 +833,6 @@ ns8250_bus_probe(struct uart_softc *sc)
 	struct uart_bas *bas;
 	int count, delay, error, limit;
 	uint8_t lsr, mcr, ier;
-	uint8_t val;
 
 	bas = &sc->sc_bas;
 
@@ -880,11 +865,7 @@ ns8250_bus_probe(struct uart_softc *sc)
 	 * done. Since this is the first time we enable the FIFOs, we reset
 	 * them.
 	 */
-	val = FCR_ENABLE;
-#ifdef CPU_XBURST
-	val |= FCR_UART_ON;
-#endif
-	uart_setreg(bas, REG_FCR, val);
+	uart_setreg(bas, REG_FCR, FCR_ENABLE);
 	uart_barrier(bas);
 	if (!(uart_getreg(bas, REG_IIR) & IIR_FIFO_MASK)) {
 		/*
@@ -898,11 +879,7 @@ ns8250_bus_probe(struct uart_softc *sc)
 		return (0);
 	}
 
-	val = FCR_ENABLE | FCR_XMT_RST | FCR_RCV_RST;
-#ifdef CPU_XBURST
-	val |= FCR_UART_ON;
-#endif
-	uart_setreg(bas, REG_FCR, val);
+	uart_setreg(bas, REG_FCR, FCR_ENABLE | FCR_XMT_RST | FCR_RCV_RST);
 	uart_barrier(bas);
 
 	count = 0;
@@ -912,11 +889,7 @@ ns8250_bus_probe(struct uart_softc *sc)
 	error = ns8250_drain(bas, UART_DRAIN_RECEIVER|UART_DRAIN_TRANSMITTER);
 	if (error) {
 		uart_setreg(bas, REG_MCR, mcr);
-		val = 0;
-#ifdef CPU_XBURST
-		val |= FCR_UART_ON;
-#endif
-		uart_setreg(bas, REG_FCR, val);
+		uart_setreg(bas, REG_FCR, 0);
 		uart_barrier(bas);
 		goto describe;
 	}
@@ -947,11 +920,7 @@ ns8250_bus_probe(struct uart_softc *sc)
 			ier = uart_getreg(bas, REG_IER) & 0xe0;
 			uart_setreg(bas, REG_IER, ier);
 			uart_setreg(bas, REG_MCR, mcr);
-			val = 0;
-#ifdef CPU_XBURST
-			val |= FCR_UART_ON;
-#endif
-			uart_setreg(bas, REG_FCR, val);
+			uart_setreg(bas, REG_FCR, 0);
 			uart_barrier(bas);
 			count = 0;
 			goto describe;