PERFORCE change 135946 for review
Kip Macy
kmacy at FreeBSD.org
Fri Feb 22 08:22:49 UTC 2008
http://perforce.freebsd.org/chv.cgi?CH=135946
Change 135946 by kmacy at pandemonium:kmacy:xen31 on 2008/02/22 08:22:28
remove unneeded devices
Affected files ...
.. //depot/projects/xen31/sys/i386/conf/XEN#5 edit
Differences ...
==== //depot/projects/xen31/sys/i386/conf/XEN#5 (text+ko) ====
@@ -79,35 +79,8 @@
#device cpufreq # native only
# Bus support.
-device eisa
device pci
-# Floppy drives
-device fdc
-
-# ATA and ATAPI devices
-device ata
-device atadisk # ATA disk drives
-device ataraid # ATA RAID drives
-device atapicd # ATAPI CDROM drives
-device atapifd # ATAPI floppy drives
-device atapist # ATAPI tape drives
-options ATA_STATIC_ID # Static device numbering
-
-# SCSI Controllers
-device ahc # AHA2940 and onboard AIC7xxx devices
-options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
- # output. Adds ~128k to driver.
-device ahd # AHA39320/29320 and onboard AIC79xx devices
-options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
- # output. Adds ~215k to driver.
-device hptiop # Highpoint RocketRaid 3xxx series
-device isp # Qlogic family
-#device ispfw # Firmware for QLogic HBAs- normally a module
-device mpt # LSI-Logic MPT-Fusion
-#device ncr # NCR/Symbios Logic
-
-
# SCSI peripherals
device scbus # SCSI bus (required for SCSI)
device ch # SCSI media changers
@@ -121,11 +94,8 @@
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
-
device kbdmux # keyboard multiplexer
-
#device vga # VGA video card driver
-
device splash # Splash screen and screen saver support
# syscons is the default console driver, resembling an SCO console
@@ -137,23 +107,9 @@
# Add suspend/resume support for the i8254.
#device pmtimer # native
-# PCCARD (PCMCIA) support
-# PCMCIA and cardbus bridge support
-device cbb # cardbus (yenta) bridge
-device pccard # PC Card (16-bit) bus
-device cardbus # CardBus (32-bit) bus
-
# Serial (COM) ports
device uart # Generic UART driver
-# Parallel port
-device ppc
-device ppbus # Parallel port bus (required)
-device lpt # Printer
-device plip # TCP/IP over parallel
-device ppi # Parallel port interface device
-#device vpo # Requires scbus and da
-
# If you've got a "dumb" serial or parallel PCI card that is
# supported by the puc(4) glue driver, uncomment the following
# line to enable it (connects to sio, uart and/or ppc drivers):
@@ -165,9 +121,6 @@
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
-device bce # Broadcom BCM5706/BCM5708 Gigabit Ethernet
-device bfe # Broadcom BCM440x 10/100 Ethernet
-device bge # Broadcom BCM570xx Gigabit Ethernet
# Pseudo devices.
device loop # Network loopback
@@ -192,3 +145,12 @@
nooption NATIVE
nodevice atpic
options MCLSHIFT=12
+
+nodevice isa
+nooption ISAPNP
+
+options KTR
+options KTR_COMPILE=(KTR_VM|KTR_PMAP|KTR_TRAP)
+options KTR_CPUMASK=0xff
+options KTR_ENTRIES=8192
+options KTR_MASK=(KTR_VM|KTR_PMAP|KTR_TRAP)
More information about the p4-projects
mailing list