fantec db 229 U3

[zulu]

Hi,

I can't use my external HDD attached to my laptop. The drive enclosure
is a Fantec db 229 U3 case (USB3). My laptop has only USB2 ports.

I have tested this with both FreeBSD 9.0 RELEASE and FreeBSD 9 STABLE
- same issues.

Tested with linux too on the same hardware and it is working fine. The
manual which came with the drive enclosure states Linux, Mac OSX and
Windows support.

Can someone please point me to the right direction? I have included
some dumps bellow.

Many thanks,

Peter

dmesg:

usb_alloc_device: set address 2 failed (USB_ERR_STALLED, ignored)

usbd_setup_device_desc: getting device descriptor at addr 2 failed,
USB_ERR_STALLED
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED,
ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed,
USB_ERR_STALLED
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED,
ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed,
USB_ERR_STALLED
ugen1.2:  at usbus1 (disconnected)

uhub_reattach_port: could not allocate new device

usbconfig output:

ugen0.1:  at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
ugen1.1:  at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
ugen2.1:  at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE
ugen3.1:  at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
ugen4.1:  at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
ugen5.1:  at usbus5, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
ugen6.1:  at usbus6, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE
ugen0.2:  at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen0.3:  at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen4.2:  at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON

pciconf:

uhci2 at pci0:0:29:0:class=0x0c0300 card=0x20aa17aa chip=0x28308086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x18a0, size 32, enabled
uhci3 at pci0:0:29:1:class=0x0c0300 card=0x20aa17aa chip=0x28318086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x18c0, size 32, enabled
uhci4 at pci0:0:29:2:class=0x0c0300 card=0x20aa17aa chip=0x28328086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x18e0, size 32, enabled
ehci1 at pci0:0:29:7:class=0x0c0320 card=0x20ab17aa chip=0x28368086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB2 EHCI Controller'
class = serial bus
subclass = USB
bar [10] = type Memory, range 32, base 0xfe227000, size 1024, enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14