Transcend JetFlash V85

[Volodymyr Kostyrko]

21.08.2010 21:29, Hans Petter Selasky wrote:
>>> You can use usbconfig to add quirks on the fly. See:
>>>
>>> usbconfig -h
>>>
>>> And:
>>>
>>> man usbconfig
>>
>> Tried that, but it doesn't work for me or I'm messing things up...
>>
>> usbconfig -d 3.3 add_quirk UQ_MSC_NO_SYNC_CACHE
>>
>> And errors continue to show up. The man page also is kinda short on data.
>
> After setting the quirk, you need to reset or re-attach the USB device.

Not a good behavior for me. What if I need to boot from one? Most FS 
don't like been pushed off device.

But this doesn't work too.

usbconfig -d 3.3 add_quirk UQ_MSC_NO_TEST_UNIT_READY
usbconfig -d 3.3 reset

Gives me:

Aug 21 22:46:14 limbo kernel: umass1: at uhub3, port 5, addr 3 
(disconnected)
Aug 21 22:46:14 limbo kernel: (da4:umass-sim1:1:0:0): lost device
Aug 21 22:46:14 limbo kernel: (da4:umass-sim1:1:0:0): removing device entry
Aug 21 22:46:15 limbo root: Unknown USB device: vendor 0x058f product 
0x6387 bus uhub3
Aug 21 22:46:15 limbo kernel: umass1: <JetFlash Mass Storage Device, 
class 0/0, rev 2.00/1.00, addr 3> on usbus3
Aug 21 22:46:15 limbo kernel: umass1:  SCSI over Bulk-Only; quirks = 0x0100

Here, quirks field doesn't change when I add more quirks.

Aug 21 22:46:16 limbo kernel: umass1:2:1:-1: Attached to scbus2
Aug 21 22:46:16 limbo kernel: (probe0:umass-sim1:1:0:0): TEST UNIT 
READY. CDB: 0 0 0 0 0 0
Aug 21 22:46:16 limbo kernel: (probe0:umass-sim1:1:0:0): CAM status: 
SCSI Status Error
Aug 21 22:46:16 limbo kernel: (probe0:umass-sim1:1:0:0): SCSI status: 
Check Condition
Aug 21 22:46:16 limbo kernel: (probe0:umass-sim1:1:0:0): SCSI sense: 
UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed)
Aug 21 22:46:16 limbo kernel: da4 at umass-sim1 bus 1 scbus2 target 0 lun 0
Aug 21 22:46:16 limbo kernel: da4: <JetFlash TS4GJFV85 8.07> Removable 
Direct Access SCSI-2 device
Aug 21 22:46:16 limbo kernel: da4: 40.000MB/s transfers
Aug 21 22:46:16 limbo kernel: da4: 3900MB (7987200 512 byte sectors: 
255H 63S/T 497C)
Aug 21 22:46:24 limbo kernel: (da4:umass-sim1:1:0:0): SYNCHRONIZE 
CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0
Aug 21 22:46:24 limbo kernel: (da4:umass-sim1:1:0:0): CAM status: SCSI 
Status Error
Aug 21 22:46:24 limbo kernel: (da4:umass-sim1:1:0:0): SCSI status: Check 
Condition
Aug 21 22:46:24 limbo kernel: (da4:umass-sim1:1:0:0): SCSI sense: 
ILLEGAL REQUEST asc:26,0 (Invalid field in parameter list)

Mentioned patch was looking like:

USB_QUIRK(ALCOR, TRANSCEND, 0x0142, 0x0142, UQ_MSC_FORCE_WIRE_BBB, 
UQ_MSC_FORCE_PROTO_SCSI, UQ_MSC_NO_GETMAXLUN, UQ_MSC_NO_SYNC_CACHE),

But I don't understand what should be set for my flash at 3-4 places... 
They are covering some range but inspecting my flash I don't see 
something close to the 0x142.

-- 
Sphinx of black quartz judge my vow.