Novatel U727 not recognized

[Kim Culhan]

On Thu, Feb 26, 2009 at 10:22 AM, Hans Petter Selasky <hselasky at c2i.net> wrote:
> On Thursday 26 February 2009, Kim Culhan wrote:
>> On Wed, Feb 25, 2009 at 1:59 AM, Hans Petter Selasky <hselasky at c2i.net>
>
> Hi,
>
> I've checked the device tables and your device is listed in the U3G driver.
>
> Try:
>
> sysctl hw.usb2.u3g.debug=15
> sysctl hw.usb.u3g.debug=15
>
> kldload usb2_serial_3g
> kldload u3g
>
> Then re-plug your device, wait up to 30 seconds having it plugged and send
> dmesg.

Ok, in this order after a fresh reboot:

# kldload usb2_serial_3g
kldload: can't load usb2_serial_3g: No such file or directory
# kldload u3g
# sysctl hw.usb2.u3g.debug=15
hw.usb2.u3g.debug: 0 -> 15

[plug in the device and wait 1 minute]


# dmesg
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #1: Wed Feb 25 17:25:14 EST 2009
    kimc at smallster:/usr/src/sys/i386/compile/smallster_no3g
WARNING: WITNESS option enabled, expect reduced performance.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz (2400.10-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6f6  Stepping = 6
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
  Cores per package: 2
real memory  = 3184525312 (3037 MB)
avail memory = 3106189312 (2962 MB)
ACPI APIC Table: <INTEL  A M I>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <INTEL DG45ID> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xf1c0-0xf1c7 mem
0xff000000-0xff3fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on
pci0
agp0: <Intel G45 SVGA controller> on vgapci0
agp0: detected 32764k stolen memory
agp0: aperture size is 256M
vgapci1: <VGA-compatible display> mem 0xff400000-0xff4fffff at device
2.1 on pci0
pci0: <simple comms> at device 3.0 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0xf100-0xf11f
mem 0xff600000-0xff61ffff,0xff624000-0xff624fff irq 20 at device 25.0
on pci0
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:1c:c0:7d:91:f5
uhci0: <UHCI (generic) USB controller> port 0xf0e0-0xf0ff irq 16 at
device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x1f30
usbus0: <UHCI (generic) USB controller> on uhci0
uhci1: <UHCI (generic) USB controller> port 0xf0c0-0xf0df irq 21 at
device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x0f30
usbus1: <UHCI (generic) USB controller> on uhci1
uhci2: <UHCI (generic) USB controller> port 0xf0a0-0xf0bf irq 18 at
device 26.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x0f30
usbus2: <UHCI (generic) USB controller> on uhci2
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xff625c00-0xff625fff
irq 18 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus3: waiting for BIOS to give up control
usbus3: timed out waiting for BIOS
usbus3: EHCI version 1.0
usbus3: <EHCI (generic) USB 2.0 controller> on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
uhci3: <UHCI (generic) USB controller> port 0xf080-0xf09f irq 23 at
device 29.0 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x0f30
usbus4: <UHCI (generic) USB controller> on uhci3
uhci4: <UHCI (generic) USB controller> port 0xf060-0xf07f irq 19 at
device 29.1 on pci0
uhci4: [ITHREAD]
uhci4: LegSup = 0x0f30
usbus5: <UHCI (generic) USB controller> on uhci4
uhci5: <UHCI (generic) USB controller> port 0xf040-0xf05f irq 18 at
device 29.2 on pci0
uhci5: [ITHREAD]
uhci5: LegSup = 0x0f30
usbus6: <UHCI (generic) USB controller> on uhci5
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xff625800-0xff625bff
irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: waiting for BIOS to give up control
usbus7: timed out waiting for BIOS
usbus7: EHCI version 1.0
usbus7: <EHCI (generic) USB 2.0 controller> on ehci1
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
fwohci0: <Lucent FW322/323> mem
0xff500000-0xff500fff,0xff501000-0xff5010ff irq 22 at device 1.0 on
pci1
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:90:27:00:02:29:cb:25
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xbdcd8000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:90:27:29:cb:25
fwe0: Ethernet address: 02:90:27:29:cb:25
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:90:27:00:02:29:cb:25 @ 0xfffe00000000,
S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel AHCI controller> port
0xf1b0-0xf1b7,0xf1a0-0xf1a3,0xf190-0xf197,0xf180-0xf183,0xf020-0xf03f
mem 0xff625000-0xff6257ff irq 19 at device 31.2 on pci0
atapci0: [ITHREAD]
atapci0: AHCI Version 01.20 controller with 6 ports PM not supported
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
ata6: <ATA channel 4> on atapci0
ata6: [ITHREAD]
ata7: <ATA channel 5> on atapci0
ata7: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci1: <Intel ICH10 SATA300 controller> port
0xf170-0xf177,0xf160-0xf163,0xf150-0xf157,0xf140-0xf143,0xf130-0xf13f,0xf120-0xf12f
irq 19 at device 31.5 on pci0
atapci1: [ITHREAD]
ata8: <ATA channel 0> on atapci1
ata8: [ITHREAD]
ata9: <ATA channel 1> on atapci1
ata9: [ITHREAD]
acpi_button0: <Power Button> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 92a092a0600092a
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 92a092a0600092a
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me)
firewire0: bus manager 0
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ad4: 476940MB <Seagate ST3500630NS 3.AEG> at ata2-master SATA300
ugen0.1: <Intel> at usbus0
ushub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
ushub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
ushub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
ushub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
ushub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
ushub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
ushub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
ushub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
GEOM: ad4: partition 3 does not start on a track boundary.
GEOM: ad4: partition 3 does not end on a track boundary.
GEOM: ad4: partition 2 does not start on a track boundary.
GEOM: ad4: partition 2 does not end on a track boundary.
GEOM: ad4: partition 1 does not start on a track boundary.
GEOM: ad4: partition 1 does not end on a track boundary.
acd0: DVDR <Optiarc DVD RW AD-7220S/1.00> at ata3-master SATA150
GEOM: ad4s3: geometry does not match label (255h,63s != 16h,63s).
ushub0: 2 ports with 2 removable, self powered
ushub1: 2 ports with 2 removable, self powered
ushub2: 2 ports with 2 removable, self powered
ushub4: 2 ports with 2 removable, self powered
ushub5: 2 ports with 2 removable, self powered
ushub6: 2 ports with 2 removable, self powered
ushub3: 6 ports with 6 removable, self powered
ushub7: 6 ports with 6 removable, self powered
ugen0.2: <Key Tronic> at usbus0
ukbd0: <icKeytronic USB Keyboard1234> on usbus0
kbd2 at ukbd0
ugen1.2: <Microsoft> at usbus1
ums0: <Microsoft Microsoft 3-Button Mouse with IntelliEye(TM), class
0/0, rev 1.10/3.00, addr 2> on usbus1
ums0: 3 buttons and [XYZ] coordinates
Symlink: ums0 -> usb1.2.0.16
SMP: AP CPU #1 Launched!
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from ufs:/dev/ad4s3a
module_register: module ushub/ums already exists!
Module ushub/ums failed to register: 17
em0: link state changed to UP
usb2_test_autoinstall:559: Eject CD command status: USB_ERR_NORMAL_COMPLETION
usb2_alloc_device:1662: Found Huawei auto-install disk!
ugen2.2: <Novatel Wireless Inc.> at usbus2
ugen2.2: <Novatel Wireless Inc.> at usbus2 (disconnected)
uhub_reattach_port:414: could not allocate new device!


-kim