u-boot-a64-olinuxino difference between U-Boot SPL 2019.10 & U-Boot SPL 2019.07

Gary Otten gdotten at gmail.com
Sat Oct 26 18:35:26 UTC 2019 

I am working on getting all the gpios on the Olimex a64 board working. You
responded to that post as well, Thanks.  You said I have to change the
overlay to turn on a voltage regulator.  So I did recently build uboot from
the source.  Perhaps that would be a different version, if it rebuilds
loader.efi?

On Sat, Oct 26, 2019 at 1:50 PM Emmanuel Vadot <manu at bidouilliste.com>
wrote:

> On Sat, 26 Oct 2019 13:30:46 -0400
> Gary Otten <gdotten at gmail.com> wrote:
>
> > I placed the file loader.efi in the /efi/boot/ directory , uboot didn't
> > appear to find it.    I also renamed loader.efi to bootaa64.efi. Results
> > for both attempts are below.
> >
> > loader.efi placed in /efi/boot/
> > ***************************************************************
> > U-Boot SPL 2019.10 (Oct 22 2019 - 12:39:22 -0400)
> > DRAM: 1024 MiB
> > Trying to boot from MMC1
> > NOTICE:  BL31: v2.1(release):
> > NOTICE:  BL31: Built : 10:11:05, Oct 20 2019
> > NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)
> > NOTICE:  BL31: Found U-Boot DTB at 0x408c458, model: Olimex A64-Olinuxino
> > NOTICE:  BL31: PMIC: Detected AXP803 on RSB.
> >
> >
> > U-Boot 2019.10 (Oct 22 2019 - 12:39:22 -0400) Allwinner Technology
> >
> > CPU:   Allwinner A64 (SUN50I)
> > Model: Olimex A64-Olinuxino
> > DRAM:  1 GiB
> > MMC:   mmc at 1c0f000: 0, mmc at 1c10000: 1
> > Loading Environment from FAT... Card did not respond to voltage select!
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   phy interface7
> > eth0: ethernet at 1c30000
> > starting USB...
> > Bus usb at 1c1a000: USB EHCI 1.00
> > Bus usb at 1c1a400: USB OHCI 1.0
> > Bus usb at 1c1b000: USB EHCI 1.00
> > Bus usb at 1c1b400: USB OHCI 1.0
> > scanning bus usb at 1c1a000 for devices... 1 USB Device(s) found
> > scanning bus usb at 1c1a400 for devices... 1 USB Device(s) found
> > scanning bus usb at 1c1b000 for devices... 1 USB Device(s) found
> > scanning bus usb at 1c1b400 for devices... 1 USB Device(s) found
> >        scanning usb for storage devices... 0 Storage Device(s) found
> > Hit any key to stop autoboot:  0
> > switch to partitions #0, OK
> > mmc0 is current device
> > Scanning mmc 0:1...
> > 32443 bytes read in 8 ms (3.9 MiB/s)
> > Card did not respond to voltage select!
> >
> > Device 0: unknown device
> > ethernet at 1c30000 Waiting for PHY auto negotiation to complete.........
> > TIMEOUT !
> > BOOTP broadcast 1
> >
> >
> >
> > I renamed loader.efi to bootaa64.efi, the result is below placed in
> > /efi/boot/
> > **********************************************************************
> >
> > U-Boot SPL 2019.10 (Oct 22 2019 - 12:39:22 -0400)
> > DRAM: 1024 MiB
> > Trying to boot from MMC1
> > NOTICE:  BL31: v2.1(release):
> > NOTICE:  BL31: Built : 10:11:05, Oct 20 2019
> > NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)
> > NOTICE:  BL31: Found U-Boot DTB at 0x408c458, model: Olimex A64-Olinuxino
> > NOTICE:  BL31: PMIC: Detected AXP803 on RSB.
> >
> >
> > U-Boot 2019.10 (Oct 22 2019 - 12:39:22 -0400) Allwinner Technology
> >
> > CPU:   Allwinner A64 (SUN50I)
> > Model: Olimex A64-Olinuxino
> > DRAM:  1 GiB
> > MMC:   mmc at 1c0f000: 0, mmc at 1c10000: 1
> > Loading Environment from FAT... Card did not respond to voltage select!
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   phy interface7
> > eth0: ethernet at 1c30000
> > starting USB...
> > Bus usb at 1c1a000: USB EHCI 1.00
> > Bus usb at 1c1a400: USB OHCI 1.0
> > Bus usb at 1c1b000: USB EHCI 1.00
> > Bus usb at 1c1b400: USB OHCI 1.0
> > scanning bus usb at 1c1a000 for devices... 1 USB Device(s) found
> > scanning bus usb at 1c1a400 for devices... 1 USB Device(s) found
> > scanning bus usb at 1c1b000 for devices... 1 USB Device(s) found
> > scanning bus usb at 1c1b400 for devices... 1 USB Device(s) found
> >        scanning usb for storage devices... 0 Storage Device(s) found
> > Hit any key to stop autoboot:  0
> > switch to partitions #0, OK
> > mmc0 is current device
> > Scanning mmc 0:1...
> > 32443 bytes read in 8 ms (3.9 MiB/s)
> > Found EFI removable media binary efi/boot/bootaa64.efi
> > Scanning disk mmc at 1c0f000.blk...
> > Card did not respond to voltage select!
> > Scanning disk mmc at 1c10000.blk...
> > Disk mmc at 1c10000.blk not ready
> > Found 3 disks
> > BootOrder not defined
> > EFI boot manager: Cannot load any image
> > 607648 bytes read in 34 ms (17 MiB/s)
> > Consoles: EFI console
> > efipart_readwrite: rw=1, blk=0 size=1 status=2
> > efipart_readwrite: rw=1, blk=64 size=1 status=2
> > efipart_readwrite: rw=1, blk=1 size=1 status=2
> > efipart_readwrite: rw=1, blk=30375936 size=1 status=2
> > efipart_readwrite: rw=1, blk=0 size=1 status=2
> > efipart_readwrite: rw=1, blk=64 size=1 status=2
> > efipart_readwrite: rw=1, blk=1 size=1 status=2
> > efipart_readwrite: rw=1, blk=30375936 size=1 status=2
> > FreeBSD/arm64 EFI loader, Revision 1.1
> >
> >    Command line arguments: loader.efi
> >    EFI version: 2.80
> >    EFI Firmware: Das U-Boot (rev 8217.4096)
> >    Console: efi (0)
> >    Load Path: /efi\boot\bootaa64.efi
> >    Load Device:
> >
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(1,0x01,0,0x800,0x64000)
> > Trying ESP:
> >
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(1,0x01,0,0x800,0x64000)
> > Setting currdev to disk0p1:
> > efipart_readwrite: rw=1, blk=0 size=1 status=2
> > efipart_readwrite: rw=1, blk=64 size=1 status=2
> > efipart_readwrite: rw=1, blk=1 size=1 status=2
> > efipart_readwrite: rw=1, blk=30375936 size=1 status=2
> > efipart_readwrite: rw=1, blk=0 size=1 status=2
> > efipart_readwrite: rw=1, blk=64 size=1 status=2
> > efipart_readwrite: rw=1, blk=1 size=1 status=2
> > efipart_readwrite: rw=1, blk=30375936 size=1 status=2
> > Trying:
> >
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(2,0x01,0,0x64800,0x1c93800)
> > Setting currdev to disk0p2:
> > efipart_readwrite: rw=1, blk=0 size=1 status=2
> > efipart_readwrite: rw=1, blk=64 size=1 status=2
> > efipart_readwrite: rw=1, blk=1 size=1 status=2
> > efipart_readwrite: rw=1, blk=30375936 size=1 status=2
> > efipart_readwrite: rw=1, blk=0 size=1 status=2
> > efipart_readwrite: rw=1, blk=64 size=1 status=2
> > efipart_readwrite: rw=1, blk=1 size=1 status=2
> > efipart_readwrite: rw=1, blk=30375936 size=1 status=2
> > Failed to find bootable partition
> > ## Application terminated, r = 14 in 1 seconds
> > EFI LOAD FAILED: continuing...
> > Card did not respond to voltage select!
> >
> > Device 0: unknown device
> > ethernet at 1c30000 Waiting for PHY auto negotiation to complete.......
>
>  When was this loader.efi built ?
>  All the needed commits have made the 12-stable and 12.1 branch so you
> shouldn't have this problem.
>
> > On Fri, Oct 25, 2019 at 4:18 AM Emmanuel Vadot <manu at bidouilliste.com>
> > wrote:
> >
> > >
> > >  Hi Gary,
> > >
> > > On Thu, 24 Oct 2019 19:37:48 -0400
> > > Gary Otten <gdotten at gmail.com> wrote:
> > >
> > > > The 2019.10 u-boot I compiled with with the a64-olinuxino_defconfig
> > > > configuration doesn't find the UFS partition the old one 2019.07
> that is
> > > in
> > > > the ports pre-compiled does.  Is there a configuration setting that I
> > > must
> > > > set before compiling?  Or did I overlook something else? Is my SD
> card
> > > > layout appropriate, or causing the problem?
> > > >
> > > >
> > >
> ***********************************************************************************
> > > > U-Boot SPL 2019.07  (from the pre-made package)    (this works)
> > > > (partial bootup txt)
> > > >
> > > >   Initializing modules: ZFS UFS
> > > >    Load Path: /efi\boot\bootaa64.efi
> > > >    Load Device:
> > > >
> > >
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(1,0x01,0,0x800,0x64000)
> > > >    Probing 3 block devices.....* done
> > > >     ZFS found no pools
> > > >     UFS found 1 partition
> > > > Consoles: EFI console
> > > > FreeBSD/arm64 EFI loader, Revision 1.1
> > > >
> > > >    Command line arguments: loader.efi
> > > >    EFI version: 2.70
> > > >    EFI Firmware: Das U-Boot (rev 8217.1792)
> > > >    Console: efi (0)
> > > >  Load Device:
> > > >
> > >
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(2,0x01,0,0x96800,0x1c8b800)
> > > > Trying ESP:
> > > >
> > >
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(2,0x01,0,0x96800,0x1c8b800)
> > > > Setting currdev to disk0p2:
> > > > Loading /boot/defaults/loader.conf
> > > > Loading /boot/device.hints
> > > > Loading /boot/loader.conf
> > > > Loading /boot/loader.conf.local
> > > > -
> > > > Loading kernel...
> > > >
> > > >
> > >
> *******************************************************************************
> > > >
> > > >
> > > >   U-Boot SPL 2019.10 (Compiled by myself)
> > > >   (partial bootup txt)
> > > >
> > > >  Initializing modules: ZFS UFS
> > > >    Load Path: /efi\boot\bootaa64.efi
> > > >    Load Device:
> > > >
> > >
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(1,0x01,0,0x800,0x64000)
> > > >    Probing 3 block devices...... done
> > > >     ZFS found no pools
> > > >     UFS found no partitions
> > > > Failed to load '/boot/loader.efi'
> > > > panic: No bootable partitions found!
> > > > ## Application terminated, r = 1
> > > > EFI LOAD FAILED: continuing...
> > > > Card did not respond to voltage select!
> > > > Device 0: unknown device
> > > > ethernet at 1c30000 Waiting for PHY auto negotiation to
> complete.........
> > > > TIMEOUT !
> > > > BOOTP broadcast 1
> > > > BOOTP broadcast 2
> > > > BOOTP broadcast 3
> > > >
> > >
> ****************************************************************************************************
> > > > My SD card layout.
> > > >
> > > > da2   MBR (15G)
> > > >            free  (993k)
> > > >     1  efi (200M)
> > > >            free (100M)
> > > >     2 freebsd  (active)  (14G)
> > > >
> > > >
> > > > da2s2    BSD (14G)
> > > >      1  freebsd-ufs   (14G)
> > > > _______________________________________________
> > > > freebsd-uboot at freebsd.org mailing list
> > > > https://lists.freebsd.org/mailman/listinfo/freebsd-uboot
> > > > To unsubscribe, send any mail to "
> freebsd-uboot-unsubscribe at freebsd.org"
> > >
> > >  You are using boot1.efi as EFI/BOOT/BOOTAA64.EFI while you should use
> > > loader.efi directly.
> > >  U-Boot 2019.10 changed some stuff related to alignement for IO and
> > > only loader.efi was updated to cope with this changed.
> > >  boot1.efi was never really supported on aarch64.
> > >
> > >  Cheers,
> > >
> > > --
> > > Emmanuel Vadot <manu at bidouilliste.com>
> > >
> > _______________________________________________
> > freebsd-uboot at freebsd.org mailing list
> > https://lists.freebsd.org/mailman/listinfo/freebsd-uboot
> > To unsubscribe, send any mail to "freebsd-uboot-unsubscribe at freebsd.org"
>
>
> --
> Emmanuel Vadot <manu at bidouilliste.com> <manu at freebsd.org>
>

More information about the freebsd-uboot mailing list