siis_timeout with port multiplier on 9.0R
Nenhum_de_Nos
matheus at eternamente.info
Wed May 23 20:07:11 UTC 2012
On Wed, May 23, 2012 12:54, Nenhum_de_Nos wrote:
>
> On Wed, May 23, 2012 11:22, Mike Tancsa wrote:
>> On 5/21/2012 9:04 PM, Matthew Gamble wrote:
>>> We have a box with 3 SiI3124 SATA controllers and 9 CFI-B53PM 5 Port Backplane port multipliers
>>> (the "backblaze storage pod"). Under intense IO (ZFS rebuild, presently) the system will lock
>>> up all IO for 3-4 minutes and the following entry appears in the dmesg:
>>>
>>> siisch11: Timeout on slot 30
>>> siisch11: siis_timeout is 00040000 ss 65000000 rs 65000000 es 00000000 sts 80192000 serr
>>> 00000000
>>> siisch11: ... waiting for slots 25000000
>>> siisch11: Timeout on slot 26
>>> siisch11: siis_timeout is 00040000 ss 65000000 rs 65000000 es 00000000 sts 80192000 serr
>>> 00000000
>>> siisch11: ... waiting for slots 21000000
>>> siisch11: Timeout on slot 29
>>> siisch11: siis_timeout is 00040000 ss 65000000 rs 65000000 es 00000000 sts 80192000 serr
>>> 00000000
>>> siisch11: ... waiting for slots 01000000
>>> siisch11: Timeout on slot 24
>>> siisch11: siis_timeout is 00040000 ss 65000000 rs 65000000 es 00000000 sts 80192000 serr
>>> 00000000
>>>
>>> The errors are on different siisch devices so its not likely to be a SATA cable issue unless
>>> multiple cables all went bad at the same time. On the advice of some other posts to the
>>> mailing
>>> list I've already tried locking the SATA rev to one with the following in /boot/loader.conf
>>> which didn't
>>
>> If they are on different siisch devices then yes, it does not sound like
>> a bad cable. However, I have had that issue with similar errors above
>> that were fixed by using new cables. If you are using 9.0R, I would
>> suggest upgrading to stable. There have been a few bug fixes /
>> improvements to the drivers as well as various parts of the disk
>> subsystem. I have RELENG8 right now and its quite stable for me on a
>> 25TB system which is for the most part similar to 9.x
>>
>> # zpool status
>> pool: zbackup1
>> state: ONLINE
>> scan: scrub repaired 0 in 11h11m with 0 errors on Mon Jul 25 19:51:11 2011
>> config:
>>
>> NAME STATE READ WRITE CKSUM
>> zbackup1 ONLINE 0 0 0
>> raidz1-0 ONLINE 0 0 0
>> ada14 ONLINE 0 0 0
>> ada16 ONLINE 0 0 0
>> ada13 ONLINE 0 0 0
>> ada15 ONLINE 0 0 0
>> raidz1-1 ONLINE 0 0 0
>> ada0 ONLINE 0 0 0
>> ada1 ONLINE 0 0 0
>> ada2 ONLINE 0 0 0
>> ada3 ONLINE 0 0 0
>> raidz1-2 ONLINE 0 0 0
>> ada4 ONLINE 0 0 0
>> ada5 ONLINE 0 0 0
>> ada6 ONLINE 0 0 0
>> ada7 ONLINE 0 0 0
>> raidz1-3 ONLINE 0 0 0
>> ada9 ONLINE 0 0 0
>> ada10 ONLINE 0 0 0
>> ada11 ONLINE 0 0 0
>> ada12 ONLINE 0 0 0
>>
>> errors: No known data errors
>> # zpool get all zbackup1
>> NAME PROPERTY VALUE SOURCE
>> zbackup1 size 25.4T -
>> zbackup1 capacity 68% -
>> zbackup1 altroot - default
>> zbackup1 health ONLINE -
>> zbackup1 guid 917659042733882722 default
>> zbackup1 version 28 default
>> zbackup1 bootfs - default
>> zbackup1 delegation on default
>> zbackup1 autoreplace off default
>> zbackup1 cachefile - default
>> zbackup1 failmode wait default
>> zbackup1 listsnapshots on local
>> zbackup1 autoexpand off default
>> zbackup1 dedupditto 0 default
>> zbackup1 dedupratio 1.00x -
>> zbackup1 free 7.95T -
>> zbackup1 allocated 17.4T -
>> zbackup1 readonly off -
>> zbackup1 comment - default
>>
>> This is on an adonics adaptor.
>
> my adapter is this adonics as well, and my lucky is not the same. the host card is also sis3124
> PCI ?
>
> I will upgrade to 9-STABLE and try.
>
> thanks,
>
> matheus
Mike,
I saw FreeBSD webcvs info on siis.c. The only change in 9-STABLE is this:
Revision 1.43.2.2: download - view: text, markup, annotated - select for diffs
Sat Dec 31 15:31:34 2011 UTC (4 months, 3 weeks ago) by hselasky
Branches: RELENG_9
Diff to: previous 1.43.2.1: preferred, colored; branchpoint 1.43: preferred, colored; next MAIN
1.44: preferred, colored
Changes since revision 1.43.2.1: +2 -7 lines
SVN rev 229118 on 2011-12-31 15:31:34Z by hselasky
MFC r227701, r227847 and r227849:
Move the device_delete_all_children() function from usb_util.c
to kern/subr_bus.c. Simplify this function so that it no longer
depends on malloc() to execute. Rename device_delete_all_children()
into device_delete_children(). Identify a few other places where
it makes sense to use device_delete_children().
all others, 9.0R has it. As i don't know this stuff, I can't tell how much it would affect my
issue (and the other Matheus/Matthew as well), but I imagine not much as it says something usb on
it :)
as I'm not at home, will try the cabling thing when I get home.
thanks,
matheus
>> ---Mike
>>>
>>> hint.siisch.0.sata_rev=1
>>> hint.siisch.1.sata_rev=1
>>> hint.siisch.2.sata_rev=1
>>> hint.siisch.3.sata_rev=1
>>> hint.siisch.4.sata_rev=1
>>> hint.siisch.5.sata_rev=1
>>> hint.siisch.6.sata_rev=1
>>> hint.siisch.7.sata_rev=1
>>> hint.siisch.8.sata_rev=1
>>> hint.siisch.9.sata_rev=1
>>> hint.siisch.10.sata_rev=1
>>> hint.siisch.11.sata_rev=1
>>>
>>> From time to time this is also causing one of the attached drives to go offline:
>>>
>>> siisch0: siis_timeout is 00040000 ss 40000000 rs 40000000 es 00000000 sts 801f2000 serr
>>> 00000000
>>> (ada0:siisch0:0:0:0): lost device
>>> (ada0:siisch0:0:0:0): removing device entry
>>> ada0 at siisch0 bus 0 scbus0 target 0 lun 0
>>> ada0: <WDC WD30EZRX-00MMMB0 80.00A80> ATA-8 SATA 3.x device
>>> ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
>>> ada0: Command Queueing enabled
>>> ada0: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
>>> ada0: Previously was known as ad4
>>> siisch11: Timeout on slot 30
>>>
>>> When the drive goes offline that causes the ZFS rebuild to restart, and so it's never finishing
>>> the rebuild of the array. Does anyone have any insight into what could be causing the timeouts
>>> and what we can do to resolve them? Right now my priority is to get the system a bit more
>>> stable so the current ZFS rebuild can complete â right now it's been doing the same rebuild
>>> for just over 6 days and the timeouts and drive drop offs are causing it to restart constantly.
>>>
>>>
>>>
>>>
>>>
>>> ________________________________
>>>
>>> This electronic message contains information from Primus Telecommunications Canada Inc.
>>> ("PRIMUS") , which may be legally privileged and confidential. The information is intended to
>>> be for the use of the individual(s) or entity named above. If you are not the intended
>>> recipient, be aware that any disclosure, copying, distribution or use of the contents of this
>>> information is prohibited. If you have received this electronic message in error, please notify
>>> us by telephone or e-mail (to the number or address above) immediately. Any views, opinions or
>>> advice expressed in this electronic message are not necessarily the views, opinions or advice
>>> of PRIMUS. It is the responsibility of the recipient to ensure that any attachments are virus
>>> free and PRIMUS bears no responsibility for any loss or damage arising in any way from the use
>>> thereof.The term "PRIMUS" includes its affiliates.
>>>
>>> ________________________________
>>> Pour la version en français de ce message, veuillez voir
>>> http://www.primustel.ca/fr/legal/cs.htm
>>>
>>>
>>>
>>> _______________________________________________
>>> freebsd-stable at freebsd.org mailing list
>>> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
>>> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org"
>>
>>
>> --
>> -------------------
>> Mike Tancsa, tel +1 519 651 3400
>> Sentex Communications, mike at sentex.net
>> Providing Internet services since 1994 www.sentex.net
>> Cambridge, Ontario Canada http://www.tancsa.com/
>> _______________________________________________
>> freebsd-stable at freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
>> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org"
>>
>
>
> --
> We will call you Cygnus,
> The God of balance you shall be
>
> A: Because it messes up the order in which people normally read text.
> Q: Why is top-posting such a bad thing?
>
> http://en.wikipedia.org/wiki/Posting_style
> _______________________________________________
> freebsd-stable at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org"
>
--
We will call you Cygnus,
The God of balance you shall be
A: Because it messes up the order in which people normally read text.
Q: Why is top-posting such a bad thing?
http://en.wikipedia.org/wiki/Posting_style
More information about the freebsd-stable
mailing list