safe mode
Stephen Clark
sclark46 at earthlink.net
Fri Oct 29 16:34:20 UTC 2010
Hello,
I am having a problem getting 6.3 to boot on an intel atom mb. When it
gets to
where it should identify the drive it hangs.
If I boot with no acpi it does the same thing.
If I boot with safe mode it comes up and identifies the drive but then
starts spewing the following errors:
ipfw2 initialized, divert enabled, rule-based forwarding disabled,
default to ad
interrupt storm detected on "irq15:"; throttling interrupt source
ad4: 152627MB <WDC WD1600BEKT-00A25T0 01.01A01> at ata2-master PIO4
interrupt storm detected on "irq15:"; throttling interrupt source
interrupt storm detected on "irq15:"; throttling interrupt source
interrupt storm detected on "irq15:"; throttling interrupt source
FreeBSD runs but I continue to get these errors:
What exactly does safe mode do - I am afraid my forth skills are not
what they
should be.
Is there some device.hints I could set to correct this problem? A
pciconf listing follows.
# pciconf -lv
hostb0 at pci0:0:0:0: class=0x060000 card=0xa0008086 chip=0xa0008086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
class = bridge
subclass = HOST-PCI
vgapci0 at pci0:0:2:0: class=0x030000 card=0xa0018086 chip=0xa0018086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
class = display
subclass = VGA
vgapci1 at pci0:0:2:1: class=0x038000 card=0xa0018086 chip=0xa0028086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
class = display
uhci0 at pci0:0:26:0: class=0x0c0300 card=0x28348086 chip=0x28348086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI'
class = serial bus
subclass = USB
uhci1 at pci0:0:26:1: class=0x0c0300 card=0x28358086 chip=0x28358086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI'
class = serial bus
subclass = USB
ehci0 at pci0:0:26:7: class=0x0c0320 card=0x283a8086 chip=0x283a8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '81EC1043 (?) ICH8 Enhanced USB2 Enhanced Host Controller'
class = serial bus
subclass = USB
none0 at pci0:0:27:0: class=0x040300 card=0xa62516f3 chip=0x284b8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H &SUBSYS_81EC1043&REV_02\3&11583659&0&D8'
class = multimedia
subclass = HDA
pcib1 at pci0:0:28:0: class=0x060400 card=0x283f8086 chip=0x283f8086
rev=0x03 hdr=0x01
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) PCIe Port 1'
class = bridge
subclass = PCI-PCI
pcib2 at pci0:0:28:3: class=0x060400 card=0x28458086 chip=0x28458086
rev=0x03 hdr=0x01
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) PCIe Port 4'
class = bridge
subclass = PCI-PCI
pcib3 at pci0:0:28:4: class=0x060400 card=0x28478086 chip=0x28478086
rev=0x03 hdr=0x01
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) PCIe Port 5'
class = bridge
subclass = PCI-PCI
uhci2 at pci0:0:29:0: class=0x0c0300 card=0x28308086 chip=0x28308086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI'
class = serial bus
subclass = USB
uhci3 at pci0:0:29:1: class=0x0c0300 card=0x28318086 chip=0x28318086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI'
class = serial bus
subclass = USB
uhci4 at pci0:0:29:2: class=0x0c0300 card=0x28328086 chip=0x28328086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB UHCI'
class = serial bus
subclass = USB
ehci1 at pci0:0:29:7: class=0x0c0320 card=0x28368086 chip=0x28368086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) USB2 EHCI'
class = serial bus
subclass = USB
pcib4 at pci0:0:30:0: class=0x060401 card=0x24488086 chip=0x24488086
rev=0xf3 hdr=0x01
vendor = 'Intel Corporation'
device = '82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to
PCI Bridge'
class = bridge
subclass = PCI-PCI
isab0 at pci0:0:31:0: class=0x060100 card=0x28158086 chip=0x28158086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = 'ICH8M-E (ICH8 Family) LPC Interface Controller'
class = bridge
subclass = PCI-ISA
atapci0 at pci0:0:31:1: class=0x01018a card=0x28508086 chip=0x28508086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) Ultra ATA Storage Controllers'
class = mass storage
subclass = ATA
atapci1 at pci0:0:31:2: class=0x01018f card=0x28288086 chip=0x28288086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = 'ICH8M (ICH8 Family) 3 port SATA Controller'
class = mass storage
subclass = ATA
none1 at pci0:0:31:3: class=0x0c0500 card=0x283e8086 chip=0x283e8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) SMBus Controller'
class = serial bus
subclass = SMBus
re0 at pci0:2:0:0: class=0x020000 card=0x816810ec chip=0x816810ec rev=0x03
hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC'
class = network
subclass = ethernet
rl0 at pci0:4:4:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10
hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
class = network
subclass = ethernet
rl1 at pci0:4:6:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10
hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
class = network
subclass = ethernet
rl2 at pci0:4:7:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10
hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
class = network
subclass = ethernet
I am stuck for now on 6.3 so moving to a later release 7+ is not feasible.
Additional info:
6.4 exhibits the same behavior. 7.2 boots okay in normal mode.
If there is a patch I could apply to 6.3 I am not averse to that.
Thanks for any help,
Steve
--
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety." (Ben Franklin)
"The course of history shows that as a government grows, liberty
decreases." (Thomas Jefferson)
More information about the freebsd-stable
mailing list