bug with some em nics on RELENG_7

Jack Vogel jfvogel at gmail.com
Thu Nov 19 17:27:39 UTC 2009


Cool, so stable/7 will just need to be updated :) I need to catch up all the

drivers in that stream actually.

Thanks for testing!!

Jack


On Thu, Nov 19, 2009 at 8:58 AM, Mike Tancsa <mike at sentex.net> wrote:

> At 07:29 PM 11/18/2009, Jack Vogel wrote:
>
>> Hey Mike,
>>
>> Can you check if you see the same behavior on RELENG 8?
>>
>
> For RELENG_8. I installed an fxp card and netbooted off it.
>
> I assigned an IP address to the onboard nic (em5). Pinged itself, got a MAC
> and response. Plugged in the cable, pinged the other side, all ok
>
> Did the same, but pinged the other side, and plugged the cable in, all
> worked as expected.
> # ping 10.177.194.18
> PING 10.177.194.18 (10.177.194.18): 56 data bytes
> ping: sendto: Host is down
> ping: sendto: Host is down
> ping: sendto: Host is down
> 64 bytes from 10.177.194.18: icmp_seq=30 ttl=64 time=1329.918 ms
> 64 bytes from 10.177.194.18: icmp_seq=31 ttl=64 time=324.925 ms
> 64 bytes from 10.177.194.18: icmp_seq=32 ttl=64 time=0.054 ms
> 64 bytes from 10.177.194.18: icmp_seq=33 ttl=64 time=0.055 ms
> 64 bytes from 10.177.194.18: icmp_seq=34 ttl=64 time=0.047 ms
> 64 bytes from 10.177.194.18: icmp_seq=35 ttl=64 time=0.050 ms
> 64 bytes from 10.177.194.18: icmp_seq=36 ttl=64 time=0.047 ms
> 64 bytes from 10.177.194.18: icmp_seq=37 ttl=64 time=0.049 ms
> 64 bytes from 10.177.194.18: icmp_seq=38 ttl=64 time=0.043 ms
>
>
> em4: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xcc00-0xcc1f mem
> 0xfaee0000-0xfaefffff,0xfaedc000-0xfaedffff irq 16 at device 0.0 on pci6
>
> em4: Using MSIX interrupts
> em4: [ITHREAD]
> em4: [ITHREAD]
> em4: [ITHREAD]
> em4: Ethernet address: 00:30:48:d6:ef:12
> pcib7: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
> pci7: <ACPI PCI bus> on pcib7
> em5: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xdc00-0xdc1f mem
> 0xfafe0000-0xfaffffff,0xfafdc000-0xfafdffff irq 17 at device 0.0 on pci7
>
> em5: Using MSIX interrupts
> em5: [ITHREAD]
> em5: [ITHREAD]
> em5: [ITHREAD]
> em5: Ethernet address: 00:30:48:d6:ef:13
>
> So the problem is _not_ there under RELENG_8.  I also tested the 2 PCIe
> nics to make sure they are still working, and they are.
>
> Full dmesg below
>
> opyright (c) 1992-2009 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>        The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 8.0-RC2 #0: Wed Nov 11 09:54:52 EST 2009
>    mdtancsa at ich10.sentex.ca:/usr/obj/usr/src/sys/alix i386
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Core(TM) i7 CPU         920  @ 2.67GHz (2660.00-MHz 686-class
> CPU)
>  Origin = "GenuineIntel"  Id = 0x106a5  Stepping = 5
>
>  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>
>  Features2=0x98e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT>
>  AMD Features=0x28100000<NX,RDTSCP,LM>
>  AMD Features2=0x1<LAHF>
>  TSC: P-state invariant
> real memory  = 6446645248 (6148 MB)
> avail memory = 3137355776 (2992 MB)
> ACPI APIC Table: <011209 APIC2037>
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> FreeBSD/SMP: 1 package(s) x 4 core(s)
>  cpu0 (BSP): APIC ID:  0
>  cpu1 (AP): APIC ID:  2
>  cpu2 (AP): APIC ID:  4
>  cpu3 (AP): APIC ID:  6
> ioapic0: Changing APIC ID to 1
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> cryptosoft0: <software crypto> on motherboard
> acpi0: <011209 XSDT2037> on motherboard
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> acpi0: reservation of 0, a0000 (3) failed
> acpi0: reservation of 100000, bff00000 (3) failed
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xac00-0xac1f mem
> 0xface0000-0xfacfffff,0xfacc0000-0xfacdffff irq 16 at device 0.0 on pci1
>
> em0: Using MSI interrupt
> em0: [FILTER]
> em0: Ethernet address: 00:15:17:78:e6:e0
> em1: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xa880-0xa89f mem
> 0xfac80000-0xfac9ffff,0xfac60000-0xfac7ffff irq 17 at device 0.1 on pci1
>
> em1: Using MSI interrupt
> em1: [FILTER]
> em1: Ethernet address: 00:15:17:78:e6:e1
> pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
> pci3: <ACPI PCI bus> on pcib3
> em2: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xbc00-0xbc1f mem
> 0xfade0000-0xfadfffff,0xfadc0000-0xfaddffff irq 16 at device 0.0 on pci3
>
> em2: Using MSI interrupt
> em2: [FILTER]
> em2: Ethernet address: 00:15:17:cf:26:de
> em3: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xb880-0xb89f mem
> 0xfad80000-0xfad9ffff,0xfad60000-0xfad7ffff irq 17 at device 0.1 on pci3
>
> em3: Using MSI interrupt
> em3: [FILTER]
> em3: Ethernet address: 00:15:17:cf:26:df
> pcib4: <ACPI PCI-PCI bridge> at device 7.0 on pci0
> pci4: <ACPI PCI bus> on pcib4
> pcib5: <ACPI PCI-PCI bridge> at device 9.0 on pci0
> pci5: <ACPI PCI bus> on pcib5
> pci0: <base peripheral, interrupt controller> at device 16.0 (no driver
> attached)
> pci0: <base peripheral, interrupt controller> at device 16.1 (no driver
> attached)
> pci0: <base peripheral, interrupt controller> at device 20.0 (no driver
> attached)
> pci0: <base peripheral, interrupt controller> at device 20.1 (no driver
> attached)
> pci0: <base peripheral, interrupt controller> at device 20.2 (no driver
> attached)
> pci0: <base peripheral, interrupt controller> at device 20.3 (no driver
> attached)
> pci0: <base peripheral> at device 22.0 (no driver attached)
> pci0: <base peripheral> at device 22.1 (no driver attached)
> pci0: <base peripheral> at device 22.2 (no driver attached)
> pci0: <base peripheral> at device 22.3 (no driver attached)
> pci0: <base peripheral> at device 22.4 (no driver attached)
> pci0: <base peripheral> at device 22.5 (no driver attached)
> pci0: <base peripheral> at device 22.6 (no driver attached)
> pci0: <base peripheral> at device 22.7 (no driver attached)
> uhci0: <UHCI (generic) USB controller> port 0x9c00-0x9c1f irq 16 at device
> 26.0 on pci0
> uhci0: [ITHREAD]
> uhci0: LegSup = 0x2f00
> usbus0: <UHCI (generic) USB controller> on uhci0
> uhci1: <UHCI (generic) USB controller> port 0x9880-0x989f irq 21 at device
> 26.1 on pci0
> uhci1: [ITHREAD]
> uhci1: LegSup = 0x2f00
> usbus1: <UHCI (generic) USB controller> on uhci1
> uhci2: <UHCI (generic) USB controller> port 0x9800-0x981f irq 19 at device
> 26.2 on pci0
> uhci2: [ITHREAD]
> uhci2: LegSup = 0x2f00
> usbus2: <UHCI (generic) USB controller> on uhci2
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfabde000-0xfabde3ff irq 18
> at device 26.7 on pci0
> ehci0: [ITHREAD]
> usbus3: EHCI version 1.0
> usbus3: <EHCI (generic) USB 2.0 controller> on ehci0
> pcib6: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
> pci6: <ACPI PCI bus> on pcib6
> em4: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xcc00-0xcc1f mem
> 0xfaee0000-0xfaefffff,0xfaedc000-0xfaedffff irq 16 at device 0.0 on pci6
>
> em4: Using MSIX interrupts
> em4: [ITHREAD]
> em4: [ITHREAD]
> em4: [ITHREAD]
> em4: Ethernet address: 00:30:48:d6:ef:12
> pcib7: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
> pci7: <ACPI PCI bus> on pcib7
> em5: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xdc00-0xdc1f mem
> 0xfafe0000-0xfaffffff,0xfafdc000-0xfafdffff irq 17 at device 0.0 on pci7
>
> em5: Using MSIX interrupts
> em5: [ITHREAD]
> em5: [ITHREAD]
> em5: [ITHREAD]
> em5: Ethernet address: 00:30:48:d6:ef:13
> uhci3: <UHCI (generic) USB controller> port 0x9480-0x949f irq 23 at device
> 29.0 on pci0
> uhci3: [ITHREAD]
> uhci3: LegSup = 0x2f00
> usbus4: <UHCI (generic) USB controller> on uhci3
> uhci4: <UHCI (generic) USB controller> port 0x9400-0x941f irq 19 at device
> 29.1 on pci0
> uhci4: [ITHREAD]
> uhci4: LegSup = 0x2f00
> usbus5: <UHCI (generic) USB controller> on uhci4
> uhci5: <UHCI (generic) USB controller> port 0x9080-0x909f irq 18 at device
> 29.2 on pci0
> uhci5: [ITHREAD]
> uhci5: LegSup = 0x2f00
> usbus6: <UHCI (generic) USB controller> on uhci5
> ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfabdc000-0xfabdc3ff irq 23
> at device 29.7 on pci0
> ehci1: [ITHREAD]
> usbus7: EHCI version 1.0
> usbus7: <EHCI (generic) USB 2.0 controller> on ehci1
> pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci8: <ACPI PCI bus> on pcib8
> fxp0: <Intel 82550 Pro/100 Ethernet> port 0xec00-0xec3f mem
> 0xfbefe000-0xfbefefff,0xfbec0000-0xfbedffff irq 17 at device 1.0 on pci8
> miibus0: <MII bus> on fxp0
> inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
> inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> fxp0: Ethernet address: 00:02:b3:5d:ca:ce
> fxp0: [ITHREAD]
> vgapci0: <VGA-compatible display> mem
> 0xf9800000-0xf9ffffff,0xfbef8000-0xfbefbfff,0xfb000000-0xfb7fffff irq 17 at
> device 4.0 on pci8
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH10 SATA300 controller> port
> 0x9000-0x9007,0x8c00-0x8c03,0x8880-0x8887,0x8800-0x8803,0x8480-0x848f,0x8400-0x840f
> irq 19 at device 31.2 on pci0
> atapci0: [ITHREAD]
> ata2: <ATA channel 0> on atapci0
> ata2: [ITHREAD]
> ata3: <ATA channel 1> on atapci0
> ata3: [ITHREAD]
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> atapci1: <Intel ICH10 SATA300 controller> port
> 0x8000-0x8007,0x7c00-0x7c03,0x7880-0x7887,0x7800-0x7803,0x7480-0x748f,0x7400-0x740f
> irq 19 at device 31.5 on pci0
> atapci1: [ITHREAD]
> ata4: <ATA channel 0> on atapci1
> ata4: [ITHREAD]
> ata5: <ATA channel 1> on atapci1
> ata5: [ITHREAD]
> acpi_button0: <Power Button> on acpi0
> atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> uart0: [FILTER]
> uart0: console (38400,n,8,1)
> uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
> uart1: [FILTER]
> uart2: <16550 or compatible> port 0x3e8-0x3ef irq 5 on acpi0
> uart2: [FILTER]
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> cpu0: <ACPI CPU> on acpi0
> ACPI Warning: Incorrect checksum in table [OEMB] - 8A, should be 87
> 20090521 tbutils-275
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 14
> device_attach: est0 attach returned 6
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> cpu1: <ACPI CPU> on acpi0
> est1: <Enhanced SpeedStep Frequency Control> on cpu1
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 14
> device_attach: est1 attach returned 6
> p4tcc1: <CPU Frequency Thermal Control> on cpu1
> cpu2: <ACPI CPU> on acpi0
> est2: <Enhanced SpeedStep Frequency Control> on cpu2
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 14
> device_attach: est2 attach returned 6
> p4tcc2: <CPU Frequency Thermal Control> on cpu2
> cpu3: <ACPI CPU> on acpi0
> est3: <Enhanced SpeedStep Frequency Control> on cpu3
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 14
> device_attach: est3 attach returned 6
> p4tcc3: <CPU Frequency Thermal Control> on cpu3
> pmtimer0 on isa0
> orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff pnpid
> ORM0000 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x100>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
> ata0: [ITHREAD]
> ata1 at port 0x170-0x177,0x376 irq 15 on isa0
> ata1: [ITHREAD]
> Timecounters tick every 1.000 msec
> IPsec: Initialized Security Association Processing.
> usbus0: 12Mbps Full Speed USB v1.0
> usbus1: 12Mbps Full Speed USB v1.0
> usbus2: 12Mbps Full Speed USB v1.0
> usbus3: 480Mbps High Speed USB v2.0
> usbus4: 12Mbps Full Speed USB v1.0
> usbus5: 12Mbps Full Speed USB v1.0
> usbus6: 12Mbps Full Speed USB v1.0
> usbus7: 480Mbps High Speed USB v2.0
> SMP: AP CPU #1 Launched!
> SMP: AP CPU #2 Launched!
> SMP: AP CPU #3 Launched!
> ugen1.1: <Intel> at usbus1ugen0.1: <Intel> at usbus0Root mount waiting
> for:ugen2.1: <Intel> at usbus2
>
>
>  usbus7 usbus6 usbus5 usbus4 usbus3 usbus2 usbus1 usbus0
> uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> ugen3.1: <Intel> at usbus3uhub1:
> <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
> uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
> ugen4.1: <Intel> at usbus4ugen5.1: <Intel> at usbus5ugen7.1: <Intel> at
> usbus7ugen6.1: <Intel> at usbus6
> uhub4:
> <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
>
> uhub5:
> <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
> uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
> uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> uhub2: 2 ports with 2 removable, self powered
> uhub4: 2 ports with 2 removable, self powered
> uhub5: 2 ports with 2 removable, self powered
> uhub6: 2 ports with 2 removable, self powered
> Root mount waiting for: usbus7 usbus3
> Root mount waiting for: usbus7 usbus3
> uhub3: 6 ports with 6 removable, self powered
> uhub7: 6 ports with 6 removable, self powered
> Trying to mount root from nfs:10.255.255.1:/home/pxe
> NFS ROOT: 10.255.255.1:/usr/home/pxe/
>
>
>        ---Mike
>
>
> --------------------------------------------------------------------
> Mike Tancsa,                                      tel +1 519 651 3400
> Sentex Communications,                            mike at sentex.net
> Providing Internet since 1994                    www.sentex.net
> Cambridge, Ontario Canada                         www.sentex.net/mike
>
>


More information about the freebsd-stable mailing list