interrupt storm

Dan Langille dan at langille.org
Tue Jan 13 17:09:29 PST 2009


Hi,

I'm getting this:

kernel: interrupt storm detected on "irq22:"; throttling interrupt source

on FreeBSD 7.1-STABLE #6: Sat Jan 10 21:45:05 EST 2009

FWIW, I got the same thing on 7.0-stable from back in May (IIRC).

Of note, atapci0 and fxp0 are both on irq 22.

Ideas?  suggestions?

Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-STABLE #6: Sat Jan 10 21:45:05 EST 2009
     dan at polo.unixathome.org:/usr/obj/usr/src/sys/PHENOM
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Phenom(tm) 9600 Quad-Core Processor (2300.18-MHz K8-class CPU)
   Origin = "AuthenticAMD"  Id = 0x100f22  Stepping = 2
 
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
   Features2=0x802009<SSE3,MON,CX16,<b23>>
   AMD 
Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
   AMD 
Features2=0x7ff<LAHF,CMP,SVM,ExtAPIC,CR8,<b5>,<b6>,<b7>,Prefetch,<b9>,<b10>>
   Cores per package: 4
usable memory = 4281454592 (4083 MB)
avail memory  = 4119994368 (3929 MB)
ACPI APIC Table: <122107 APIC0947>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
  cpu2 (AP): APIC ID:  2
  cpu3 (AP): APIC ID:  3
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <122107 RSDT0947> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cff00000 (3) failed
ACPI HPET table warning: Sequence is non-zero (2)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on 
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pci1: <ACPI PCI bus> on pcib1
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe 
Gigabit Ethernet> port 0xc800-0xc8ff mem 0xf9fff000-0xf9ffffff irq 17 at 
device 0.0 on pci1
re0: turning off MSI enable bit.
re0: Chip rev. 0x38000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
re0: Ethernet address: 00:1d:92:63:8b:28
re0: [FILTER]
pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci2: <ACPI PCI bus> on pcib2
vgapci0: <VGA-compatible display> port 0xd800-0xd87f mem 
0xfd000000-0xfdffffff,0xd0000000-0xdfffffff,0xfa000000-0xfbffffff irq 19 
at device 0.0 on pci2
atapci0: <ATI IXP600 SATA300 controller> port 
0xb000-0xb007,0xa000-0xa003,0x9000-0x9007,0x8000-0x8003,0x7000-0x700f 
mem 0xf9eff800-0xf9effbff irq 22 at device 18.0 on pci0
atapci0: [ITHREAD]
atapci0: AHCI Version 01.10 controller with 4 ports detected
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xf9efe000-0xf9efefff irq 16 
at device 19.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xf9efd000-0xf9efdfff irq 17 
at device 19.1 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ohci2: <OHCI (generic) USB controller> mem 0xf9efc000-0xf9efcfff irq 18 
at device 19.2 on pci0
ohci2: [GIANT-LOCKED]
ohci2: [ITHREAD]
usb2: OHCI version 1.0, legacy support
usb2: SMM does not respond, resetting
usb2: <OHCI (generic) USB controller> on ohci2
usb2: USB revision 1.0
uhub2: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ohci3: <OHCI (generic) USB controller> mem 0xf9efb000-0xf9efbfff irq 17 
at device 19.3 on pci0
ohci3: [GIANT-LOCKED]
ohci3: [ITHREAD]
usb3: OHCI version 1.0, legacy support
usb3: SMM does not respond, resetting
usb3: <OHCI (generic) USB controller> on ohci3
usb3: USB revision 1.0
uhub3: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ohci4: <OHCI (generic) USB controller> mem 0xf9efa000-0xf9efafff irq 18 
at device 19.4 on pci0
ohci4: [GIANT-LOCKED]
ohci4: [ITHREAD]
usb4: OHCI version 1.0, legacy support
usb4: SMM does not respond, resetting
usb4: <OHCI (generic) USB controller> on ohci4
usb4: USB revision 1.0
uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf9eff000-0xf9eff0ff irq 
19 at device 19.5 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb5: EHCI version 1.0
usb5: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4
usb5: <EHCI (generic) USB 2.0 controller> on ehci0
usb5: USB revision 2.0
uhub5: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5
uhub5: 10 ports with 10 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP600 UDMA133 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci3: <ACPI PCI bus> on pcib3
fwohci0: <VIA Fire II (VT6306)> port 0xe800-0xe87f mem 
0xfebff800-0xfebfffff irq 23 at device 0.0 on pci3
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:dc:10:00:01:53:a0:bc
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x1190000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:dc:10:53:a0:bc
fwe0: Ethernet address: 02:dc:10:53:a0:bc
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:dc:10:00:01:53:a0:bc @ 0xfffe00000000, S400, 
maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xe400-0xe43f mem 
0xfebfe000-0xfebfefff,0xfea00000-0xfeafffff irq 22 at device 2.0 on pci3
miibus1: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus1
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:04:ac:d3:78:23
fxp0: [ITHREAD]
acpi_button0: <Power Button> on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on 
acpi0
sio0: type 16550A
sio0: [FILTER]
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 
on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: CLK_VAL field overlaps THT_EN bit
device_attach: acpi_throttle0 attach returned 6
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
ppc0: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
acd0: CDRW <HL-DT-ST GCE-8523B/1.01> at ata0-slave UDMA33
ad4: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata2-master SATA300
ad6: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata3-master SATA300
GEOM_MIRROR: Device mirror/gm0 launched (2/2).
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00
cd0 at ata0 bus 0 target 1 lun 0
cd0: <HL-DT-ST CD-RW GCE-8523B 1.01> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present 
- tray closed
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/mirror/gm0s1a


More information about the freebsd-stable mailing list