6.2-STABLE Hard Freeze while using RAID1 on Adaptec 1210SA

[Gheorghe Ardelean]

Hi,

I am trying to use two SATA II disks over an Adaptec 1210SA PCI SATA
Controller (based on SiI 3112 SATA150 chip).

While trying to use the disks I get shortly the following message and the
system is hard freezing soon after that.

May 14 15:47:32 noname kernel: ad6: TIMEOUT - WRITE_DMA retrying (1 retry
left) LBA=238231007

If I move the HDD's in a computer with VIA SATA150 on board or nVIDIA
SATA150 the RAID system is working without problems with the same version
of FreeBSD.

Are there any known problems with this Adaptec controller or is the
combination controller SATA150 and HDD SATA300 not well supported?
Is there a way to fix this?

The system is installed on a 3rd disk (IDE).

Regrads,

Johny.

Here is the dmesg taken on the system with Adaptec controller:

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE-200704 #0: Sun Apr  1 11:05:41 UTC 2007
    root at dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (999.72-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x686  Stepping = 6
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 1073659904 (1023 MB)
avail memory = 1041649664 (993 MB)
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <ASUS CUV4X_EA> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xfc000000-0xfdffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686B UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xd800-0xd80f at device 4.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 11 at device 4.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 11 at device 4.3 on pci0
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
atapci1: <SiI 3112 SATA150 controller> port 0xb800-0xb807,0xb400-0xb403,0xb000-0xb007,0xa800-0xa803,0xa400-0xa40f mem 0xf8000000-0xf80001ff irq 10 at device 7.0 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xa000-0xa07f mem 0xf7800000-0xf780007f irq 11 at device 10.0 on pci0
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:01:02:fa:01:a1
fdc0: <floppy drive controller> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcc7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 999720598 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 19623MB <IBM DTLA-305020 TW2OA60A> at ata0-master UDMA100
acd0: CDROM <TOSHIBA CD-ROM XM-6702B/1007> at ata1-master UDMA33
ad4: 157066MB <Hitachi HDS721616PLA380 P22OA70A> at ata2-master SATA150
ad6: 157066MB <Hitachi HDS721616PLA380 P22OA70A> at ata3-master SATA150
ar0: 157066MB <Adaptec HostRAID RAID1> status: READY
ar0: disk0 READY (master) using ad4 at ata2-master
ar0: disk1 READY (mirror) using ad6 at ata3-master
Trying to mount root from ufs:/dev/ad0s1a