Total crash in gdb!.. something is broken!.. Was: Re: FreeBSD
with a Gigabyte GA-K8NSC?
Johan Ström
johan at stromnet.org
Sun Sep 24 23:36:28 PDT 2006
Fcking great.. Waking up and noting that the box has rebooted it self
during the night... Yay!!... No kernel dumps, nothing in message
log.. Nada... (this was on the "first" box, that is the one first in
this thread)
What exactly does
kernel dumps on /dev/mirror/gm0s1b
mean? Not that it saves any kernel dumps at least.. But otoh I have
no clue why it crashed at all and if it even did try to dump kernel
or if it just blacked out as when i tried to debug clamd...
--
Johan
On Sep 24, 2006, at 14:23 , Johan Ström wrote:
> Okay, I got some problems here now... I'm trying to get clamav's
> clamd to work.. Failes with an abort in libc:
>
> It coredumps directly on start, trace: http://sial.org/pbot/19922
> Truss output: www.stromnet.org/~johan/clamd.log
>
> Okay...something seems to be f*cked in the nss/ldap stuff..
>
> Anyway,, when running with gdb --args /usr/local/sbin/clamd --debug
> it works fine!... No coredump or anything, untill i decide to kill
> clamd..
>
> kill <pidofclamd> breaks into gdb, and when I run continue to
> process the signal and let it die, the whole fcking box dies!
> Screen goes black and reboot.. No panic messages or anything...
> I have reproduced this two times now on the box in the dmesg in
> earlier mail... Then i moved the disk to another box pretty
> similar, same chipset i thikn but not exactly same mobo.. tried the
> above commands, and bam exactly same problem.. screen just goes
> black and the box reboots... Dmesg from that box:
>
> if i can get the crap up running. now the fs is broken or some
> shit.... get this on boot, after started a few services:
>
> Starting jails:/usr: bad dir ino 32125198 at offset 512: mangled entry
> panic: ufs_dirbad: bad dir
> Uptime: 54s
> GEOM_MIRROR: Device gm0: provider mirror/gm0 destroyed
> GEOM_MIRROR: Device gm0 destroyed.
> Cannot dump. No dump device defined.
> Automatic reboot in 15 seconds...
>
> Ok, now i rebooted to singeluser mode and enalbed the dumpdev in
> rc.conf... , then saw it continune booting and i chcked for the
> line saying kernel dumps on /dev/mirror/gm0s1b... it was there...
> and then it booted further and got by the place it crashed before,
> but a minute later when i try to login to crashes on the same
> inode... AND STILL!.. it says Cannot dump. No dump device
> defined... WTF??... brokeness brokeness..
>
> Okay, after some fscking its back up. dmesg from second box which i
> can crash with clamd...:
>
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,
> 1994
> The Regents of the University of California. All rights
> reserved.
> FreeBSD 6.1-RELEASE-p7 #0: Wed Sep 20 09:21:41 CEST 2006
> admin at elfi.stromnet.org:/usr/obj/usr/src/sys/ELFI
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: AMD Athlon(tm) 64 Processor 3200+ (2210.09-MHz K8-class CPU)
> Origin = "AuthenticAMD" Id = 0xfc0 Stepping = 0
>
> Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PG
> E,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
> AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
> real memory = 1073676288 (1023 MB)
> avail memory = 1024299008 (976 MB)
> ACPI APIC Table: <Nvidia AWRDACPI>
> ioapic0 <Version 1.1> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> acpi0: <Nvidia AWRDACPI> on motherboard
> acpi0: Power Button (fixed)
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
> cpu0: <ACPI CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0xcf0-0xcf3 on acpi0
> pci0: <ACPI PCI bus> on pcib0
> agp0: <NVIDIA nForce3-250 AGP Controller> mem 0xf0000000-0xf7ffffff
> at device 0.0 on pci0
> isab0: <PCI-ISA bridge> at device 1.0 on pci0
> isa0: <ISA bus> on isab0
> pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
> ohci0: <OHCI (generic) USB controller> mem 0xfe02f000-0xfe02ffff
> irq 21 at device 2.0 on pci0
> ohci0: [GIANT-LOCKED]
> usb0: OHCI version 1.0, legacy support
> usb0: <OHCI (generic) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 4 ports with 4 removable, self powered
> ohci1: <OHCI (generic) USB controller> mem 0xfe02e000-0xfe02efff
> irq 22 at device 2.1 on pci0
> ohci1: [GIANT-LOCKED]
> usb1: OHCI version 1.0, legacy support
> usb1: <OHCI (generic) USB controller> on ohci1
> usb1: USB revision 1.0
> uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 4 ports with 4 removable, self powered
> ehci0: <NVIDIA nForce3 250 USB 2.0 controller> mem
> 0xfe02d000-0xfe02d0ff irq 23 at device 2.2 on pci0
> ehci0: [GIANT-LOCKED]
> usb2: EHCI version 1.0
> usb2: companion controllers, 4 ports each: usb0 usb1
> usb2: <NVIDIA nForce3 250 USB 2.0 controller> on ehci0
> usb2: USB revision 2.0
> uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub2: 8 ports with 8 removable, self powered
> nve0: <NVIDIA nForce MCP7 Networking Adapter> port 0xf000-0xf007
> mem 0xfe02c000-0xfe02cfff irq 21 at device 5.0 on pci0
> nve0: Ethernet address 00:11:09:c5:fc:9e
> miibus0: <MII bus> on nve0
> ukphy0: <Generic IEEE 802.3u media interface> on miibus0
> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> nve0: Ethernet address: 00:11:09:c5:fc:9e
> pci0: <multimedia, audio> at device 6.0 (no driver attached)
> atapci0: <nVidia nForce3 Pro UDMA133 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xdc00-0xdc0f at device 8.0 on
> pci0
> ata0: <ATA channel 0> on atapci0
> ata1: <ATA channel 1> on atapci0
> atapci1: <nVidia nForce3 Pro SATA150 controller> port
> 0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xc800-0xc80f,
> 0xc400-0xc47f irq 23 at device 9.0 on pci0
> ata2: <ATA channel 0> on atapci1
> ata3: <ATA channel 1> on atapci1
> atapci2: <nVidia nForce3 Pro SATA150 controller> port
> 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xb000-0xb00f,
> 0xac00-0xac7f irq 20 at device 10.0 on pci0
> ata4: <ATA channel 0> on atapci2
> ata5: <ATA channel 1> on atapci2
> pcib1: <ACPI PCI-PCI bridge> at device 11.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> pci1: <display, VGA> at device 0.0 (no driver attached)
> pcib2: <ACPI PCI-PCI bridge> at device 14.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> pci2: <multimedia, audio> at device 8.0 (no driver attached)
> xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x8800-0x887f mem
> 0xfdfff000-0xfdfff07f irq 19 at device 9.0 on pci2
> miibus1: <MII bus> on xl0
> xlphy0: <3Com internal media interface> on miibus1
> xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> xl0: Ethernet address: 00:10:5a:dc:5e:aa
> fwohci0: <VIA Fire II (VT6306)> port 0x8400-0x847f mem
> 0xfdffe000-0xfdffe7ff irq 19 at device 12.0 on pci2
> fwohci0: OHCI version 1.0 (ROM=1)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 00:10:dc:00:00:77:83:dc
> fwohci0: Phy 1394a available S400, 3 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> fwe0: <Ethernet over FireWire> on firewire0
> if_fwe0: Fake Ethernet address: 02:10:dc:77:83:dc
> fwe0: Ethernet address: 02:10:dc:77:83:dc
> fwe0: if_start running deferred for Giant
> sbp0: <SBP-2/SCSI over FireWire> on firewire0
> fwohci0: Initiate bus reset
> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> firewire0: bus manager 0 (me)
> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
> on acpi0
> fdc0: [FAST]
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags
> 0x10 on acpi0
> sio0: type 16550A
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> ppc0: <Standard parallel printer port> port 0x378-0x37f,0x778-0x77b
> irq 7 on acpi0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> ppbus0: <Parallel port bus> on ppc0
> ppbus0: IEEE1284 device found /NIBBLE/ECP
> Probing for PnP devices on ppbus0:
> ppbus0: <HEWLETT-PACKARD DESKJET 820C> SCP,VLINK
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> orm0: <ISA Option ROMs> at iomem 0xc0000-0xce7ff,0xd0000-0xd17ff on
> isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff
> on isa0
> ums0: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), rev
> 1.10/3.00, addr 2, iclass 3/1
> ums0: 5 buttons and Z dir.
> Timecounter "TSC" frequency 2210091714 Hz quality 800
> Timecounters tick every 1.000 msec
> module_register_init: MOD_LOAD (amr_linux, 0xffffffff80654f90, 0)
> error 6
> ad0: 156334MB <Maxtor 6Y160P4 YAR41BW0> at ata0-master UDMA133
> acd0: DVDR <NEC DVD RW ND-3500AG/2.16> at ata1-master UDMA33
> ad4: 286187MB <Maxtor 7L300S0 BANC1G10> at ata2-master SATA150
> GEOM_MIRROR: Device gm0 created (id=316220990).
> GEOM_MIRROR: Device gm0: provider ad4 detected.
> GEOM_MIRROR: Device gm0: provider ad4 activated.
> GEOM_MIRROR: Device gm0: provider mirror/gm0 launched.
> Trying to mount root from ufs:/dev/mirror/gm0s1a
>
>
> So.. Wtf is the problem here?...
>
> Hope someone can help me..
> Thanks
>
> On Sep 23, 2006, at 18:41 , Johan Ström wrote:
>
>>
>> On Sep 3, 2006, at 14:13 , Johan Ström wrote:
>>
>>> Hi
>>>
>>> I'm about to get a "new" server... In this case what I'm looking
>>> at is a Gigabyte GA-K8NSC mobo with nForce3 250Gb chipset, and a
>>> AMD 64 3200+ Venice S939.
>>>
>>> Does anyone have any experience with FreeBSD (6.1) and this mobo/
>>> chipset? Does the network work? How good? SATA? Any stability/
>>> performance issues?
>>>
>>> I did notice it was mentioned on http://www.freebsd.org/platforms/
>>> amd64/motherboards.html on 5.4 with the only comment "Sound and
>>> USB untested.".. So.. anyone got more detailed experience than that?
>>>
>>> Thanks :)
>>> --
>>> Johan Ström
>>> johan at stromnet.org
>>>
>>
>> Hi again,
>> I got the mobo now and everything I've tested seems to work fine,
>> network (Marvell Gigabit Ethernet) works perfect (altough just
>> using 100mbit, havent tested gig), and sata seems to work..
>> Somewhat... Thats part of why I post this..
>>
>> I got two disks plugged in currently, two pieces of ad4: 286187MB
>> <Maxtor 7L300S0 BANC1G10> at ata2-master SATA150 (ad4 and ad6) on
>> one SATA each... When I only access ad4 (the system disk) and dont
>> touch ad6 (the old system disk, moving some data form there now..
>> soon to be gmirrored with ad4) it works fine.
>> But as soon as i start to transer data from ad6 to ad4 (or rather,
>> from ad4s1f to gm0s1f of which ad6 is provider), the system
>> becomes veeerrry slow... Its still usable but it takes several
>> seconds (sometimes as much as 10-20) to ie exectue a simple
>> command like ls, top, su...
>> gstat reports speeds of around 30MB/s:
>>
>> dT: 0.501 flag_I 500000us sizeof 288 i -1
>> L(q) ops/s r/s kBps ms/r w/s kBps ms/w %busy Name
>> 17 395 12 200 577.2 383 49059 8.5 99.2| ad4
>> 17 395 12 200 577.2 383 49059 8.5 99.2|
>> mirror/gm0
>> 0 0 0 0 0.0 0 0 0.0 0.0| ad4s1
>> 17 395 12 200 577.2 383 49059 8.5 99.2|
>> mirror/gm0s1
>> 0 387 387 49570 1.1 0 0 0.0 43.0| ad6
>> 3 2 2 32 583.1 0 0 0.0 116.5|
>> mirror/gm0s1a
>> 1 0 0 0 0.0 0 0 0.0 0.0|
>> mirror/gm0s1b
>> 0 0 0 0 0.0 0 0 0.0 0.0|
>> mirror/gm0s1c
>> 0 0 0 0 0.0 0 0 0.0 0.0|
>> mirror/gm0s1d
>> 0 0 0 0 0.0 0 0 0.0 0.0|
>> mirror/gm0s1e
>> 13 393 10 168 576.0 383 49059 8.5 95.3|
>> mirror/gm0s1f
>> 0 387 387 49570 1.1 0 0 0.0 43.2| ad6s1
>> 0 0 0 0 0.0 0 0 0.0 0.0| ad6s1a
>> 0 0 0 0 0.0 0 0 0.0 0.0| ad6s1b
>> 0 0 0 0 0.0 0 0 0.0 0.0| ad6s1c
>> 0 0 0 0 0.0 0 0 0.0 0.0| ad6s1d
>> 0 0 0 0 0.0 0 0 0.0 0.0| ad6s1e
>> 0 387 387 49570 1.1 0 0 0.0 44.0| ad6s1f
>>
>> Those busy figures.. on the gmirror they fly up to > 100% all the
>> time and are red.. on the ad6 figures they are 40-50% all the time
>> (during copy that is)..
>>
>> Any ideas?
>>
>> dmesg:
>>
>> Copyright (c) 1992-2006 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
>> 1993, 1994
>> The Regents of the University of California. All rights
>> reserved.
>> FreeBSD 6.1-RELEASE-p7 #0: Wed Sep 20 09:21:41 CEST 2006
>> admin at elfi.stromnet.org:/usr/obj/usr/src/sys/ELFI
>> Timecounter "i8254" frequency 1193182 Hz quality 0
>> CPU: AMD Athlon(tm) 64 Processor 3200+ (2009.79-MHz K8-class CPU)
>> Origin = "AuthenticAMD" Id = 0x20ff0 Stepping = 0
>>
>> Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,P
>> GE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
>> Features2=0x1<SSE3>
>> AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow+,3DNow>
>> AMD Features2=0x1<LAHF>
>> real memory = 1073676288 (1023 MB)
>> avail memory = 1024299008 (976 MB)
>> ACPI APIC Table: <Nvidia AWRDACPI>
>> ioapic0 <Version 1.1> irqs 0-23 on motherboard
>> kbd1 at kbdmux0
>> acpi0: <Nvidia AWRDACPI> on motherboard
>> acpi0: Power Button (fixed)
>> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
>> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on
>> acpi0
>> cpu0: <ACPI CPU> on acpi0
>> acpi_button0: <Power Button> on acpi0
>> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0xcf0-0xcf3 on acpi0
>> pci0: <ACPI PCI bus> on pcib0
>> agp0: <NVIDIA nForce3-250 AGP Controller> mem
>> 0xf8000000-0xf9ffffff at device 0.0 on pci0
>> isab0: <PCI-ISA bridge> at device 1.0 on pci0
>> isa0: <ISA bus> on isab0
>> pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
>> ohci0: <OHCI (generic) USB controller> mem 0xfd005000-0xfd005fff
>> irq 20 at device 2.0 on pci0
>> ohci0: [GIANT-LOCKED]
>> usb0: OHCI version 1.0, legacy support
>> usb0: SMM does not respond, resetting
>> usb0: <OHCI (generic) USB controller> on ohci0
>> usb0: USB revision 1.0
>> uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>> uhub0: 4 ports with 4 removable, self powered
>> ohci1: <OHCI (generic) USB controller> mem 0xfd000000-0xfd000fff
>> irq 21 at device 2.1 on pci0
>> ohci1: [GIANT-LOCKED]
>> usb1: OHCI version 1.0, legacy support
>> usb1: SMM does not respond, resetting
>> usb1: <OHCI (generic) USB controller> on ohci1
>> usb1: USB revision 1.0
>> uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>> uhub1: 4 ports with 4 removable, self powered
>> ehci0: <NVIDIA nForce3 250 USB 2.0 controller> mem
>> 0xfd001000-0xfd0010ff irq 22 at device 2.2 on pci0
>> ehci0: [GIANT-LOCKED]
>> usb2: EHCI version 1.0
>> usb2: companion controllers, 4 ports each: usb0 usb1
>> usb2: <NVIDIA nForce3 250 USB 2.0 controller> on ehci0
>> usb2: USB revision 2.0
>> uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
>> uhub2: 8 ports with 8 removable, self powered
>> pci0: <multimedia, audio> at device 6.0 (no driver attached)
>> atapci0: <nVidia nForce3 Pro UDMA133 controller> port
>> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 8.0 on
>> pci0
>> ata0: <ATA channel 0> on atapci0
>> ata1: <ATA channel 1> on atapci0
>> atapci1: <nVidia nForce3 Pro SATA150 controller> port
>> 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xdc00-0xdc0f,
>> 0xe000-0xe07f irq 21 at device 10.0 on pci0
>> ata2: <ATA channel 0> on atapci1
>> ata3: <ATA channel 1> on atapci1
>> pcib1: <ACPI PCI-PCI bridge> at device 11.0 on pci0
>> pci1: <ACPI PCI bus> on pcib1
>> pcib2: <ACPI PCI-PCI bridge> at device 14.0 on pci0
>> pci2: <ACPI PCI bus> on pcib2
>> pci2: <display, VGA> at device 10.0 (no driver attached)
>> skc0: <Marvell Gigabit Ethernet> port 0xa400-0xa4ff mem
>> 0xfc000000-0xfc003fff irq 19 at device 11.0 on pci2
>> skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
>> sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
>> sk0: Ethernet address: 00:14:85:21:c4:44
>> miibus0: <MII bus> on sk0
>> e1000phy0: <Marvell 88E1000 Gigabit PHY> on miibus0
>> e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
>> 1000baseTX-FDX, auto
>> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
>> on acpi0
>> fdc0: [FAST]
>> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags
>> 0x10 on acpi0
>> sio0: type 16550A
>> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
>> sio1: type 16550A
>> ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq
>> 7 drq 3 on acpi0
>> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
>> ppc0: FIFO with 16/16/16 bytes threshold
>> ppbus0: <Parallel port bus> on ppc0
>> plip0: <PLIP network interface> on ppbus0
>> lpt0: <Printer> on ppbus0
>> lpt0: Interrupt-driven port
>> ppi0: <Parallel I/O> on ppbus0
>> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
>> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
>> kbd0 at atkbd0
>> atkbd0: [GIANT-LOCKED]
>> orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
>> sc0: <System console> at flags 0x100 on isa0
>> sc0: VGA <16 virtual consoles, flags=0x300>
>> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff
>> on isa0
>> Timecounter "TSC" frequency 2009790446 Hz quality 800
>> Timecounters tick every 1.000 msec
>> module_register_init: MOD_LOAD (amr_linux, 0xffffffff80654f90, 0)
>> error 6
>> ad4: 286187MB <Maxtor 7L300S0 BANC1G10> at ata2-master SATA150
>>
>> elfi# gmirror list
>> Geom name: gm0
>> State: COMPLETE
>> Components: 1
>> Balance: round-robin
>> Slice: 4096
>> Flags: NONE
>> GenID: 0
>> SyncID: 1
>> ID: 316220990
>> Providers:
>> 1. Name: mirror/gm0
>> Mediasize: 300089646080 (279G)
>> Sectorsize: 512
>> Mode: r5w5e6
>> Consumers:
>> 1. Name: ad4
>> Mediasize: 300089646592 (279G)
>> Sectorsize: 512
>> Mode: r1w1e1
>> State: ACTIVE
>> Priority: 0
>> Flags: DIRTY
>> GenID: 0
>> SyncID: 1
>> ID: 3833124755
>>
>>
>> I just saw http://www.freebsd.org/releases/6.1R/installation-
>> amd64.html says:
>>
>> If you have an machine based on an nVidia nForce3 Pro-150, you
>> MUST use the BIOS setup to disable the IO APIC. If you do not have
>> an option to do this, you will likely have to disable ACPI
>> instead. There are bugs in the Pro-150 chipset that we have not
>> found a workaround for yet.
>>
>> Could this affect? Might try that...
>>
>> Thanks
>> Johan
>>
>>>
>>>
>>> _______________________________________________
>>> freebsd-hardware at freebsd.org mailing list
>>> http://lists.freebsd.org/mailman/listinfo/freebsd-hardware
>>> To unsubscribe, send any mail to "freebsd-hardware-
>>> unsubscribe at freebsd.org"
>>
>> _______________________________________________
>> freebsd-stable at freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
>> To unsubscribe, send any mail to "freebsd-stable-
>> unsubscribe at freebsd.org"
>
> _______________________________________________
> freebsd-stable at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-
> unsubscribe at freebsd.org"
More information about the freebsd-stable
mailing list