ACPI issue with RELENG_6

Fri Sep 22 08:38:01 PDT 2006

Hi!

With a recent RELENG_6 I've experienced what I suspect to be an ACPI
issue.

When powering down the system using `halt -p' I'm seeing a message
like 'power off using ACPI' after the system has been shut down but
the system does not power off. I've seen this yesterday with a
csup'ed system as of yesterday and also today (csup'ed last night).

I haven't had issues like that on this system before (using
RELEASE-anything or an older RELENG_6 ACPI power off did work on
that hardware).

Following is my dmesg. If you need to see something more (like ACPI
tables) please advise.

Greetings,

Volker

Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
reserved.
FreeBSD 6.2-PRERELEASE #11: Fri Sep 22 01:31:31 CEST 2006
    root at bellona.sz.vwsoft.com:/usr/obj/usr/src/sys/BELLONA
WARNING: debug.mpsafenet forced to 0 as i4b_ipr requires Giant
WARNING: MPSAFE network stack disabled, expect reduced performance.
ACPI APIC Table: <AMIINT VIA_K7  >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 2400+ (1998.05-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x681  Stepping = 1

Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400800<SYSCALL,MMX+,3DNow+,3DNow>
real memory  = 536805376 (511 MB)
avail memory = 515727360 (491 MB)
ioapic0 <Version 0.3> irqs 0-23 on motherboard
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413)
acpi0: <AMIINT VIA_K7> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 8377 (Apollo KT400/KT400A/KT600) host to PCI bridge> mem
0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
ath0: <Atheros 5212> mem 0xdffe0000-0xdffeffff irq 18 at device 10.0
on pci0
ath0: [GIANT-LOCKED]
ath0: Ethernet address: 00:09:5b:89:7d:1f
ath0: mac 5.6 phy 4.1 5ghz radio 1.7 2ghz radio 2.3
ifpi0: <AVM Fritz!Card PCI> port 0xd400-0xd41f mem
0xdfffbfe0-0xdfffbfff irq 19 at device 11.0 on pci0
ifpi0: [GIANT-LOCKED]
ifpi0: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2)
ifpi0: passive stack unit 0
ahc0: <Adaptec 29160N Ultra160 SCSI adapter> port 0xd000-0xd0ff mem
0xdfffa000-0xdfffafff irq 16 at device 12.0 on pci0
ahc0: [GIANT-LOCKED]
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
cbb0: <RF5C475 PCI-CardBus Bridge> at device 13.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
atapci0: <VIA 6420 SATA150 controller> port
0xec00-0xec07,0xe800-0xe803,0xe400-0xe407,0xe000-0xe003,0xdc00-0xdc0f,0xd800-0xd8ff
irq 20 at device 15.0 on pci0
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
atapci1: <VIA 8237 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 15.1 on pci0
ata0: <ATA channel 0> on atapci1
ata1: <ATA channel 1> on atapci1
uhci0: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 21 at
device 16.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 21 at
device 16.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xc800-0xc81f irq 21 at
device 16.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <VIA 83C572 USB controller> port 0xcc00-0xcc1f irq 21 at
device 16.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xdfffbd00-0xdfffbdff irq
21 at device 16.4 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
pci0: <multimedia, audio> at device 17.5 (no driver attached)
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xb800-0xb8ff mem
0xdfffbc00-0xdfffbcff irq 23 at device 18.0 on pci0
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: Ethernet address: 00:0b:6a:7d:a9:a2
vr0: [GIANT-LOCKED]
acpi_button1: <Sleep Button> on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10
on acpi0
sio0: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <12 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
ucom0: Lucent Technologies, Inc. ELSA Modem Board, rev 1.00/1.00,
addr 2, iclass 2/2
ucom0: data interface 1, has CM over data, has break
ucom0: status change notification available
Timecounter "TSC" frequency 1998050487 Hz quality 800
Timecounters tick every 1.000 msec
i4btrc: 1 ISDN trace device(s) attached
i4bipr: 1 IP over raw HDLC ISDN device(s) attached (VJ header
compression)
i4bctl: ISDN system control port attached
i4brbch: 2 raw B channel access device(s) attached
i4bisppp: 1 ISDN SyncPPP device(s) attached
i4b: ISDN call control device attached
i4btel: 2 ISDN telephony interface device(s) attached
Fast IPsec: Initialized Security Association Processing.
pccard0: Allocation failed for cfe 7
sio1: <Novatel Wireless Merlin UMTS Modem> at port 0x2f8-0x2ff irq
17 function 0 config 15 on pccard0
sio1: type 16550A
sio1: unable to activate interrupt in fast mode - using normal mode
pccard0: Allocation failed for cfe 7
pccard0: Allocation failed for cfe 15
sio2: <Novatel Wireless Merlin UMTS Modem> at port 0x2e8-0x2ef irq
17 function 1 config 23 on pccard0
sio2: type 16550A
sio2: unable to activate interrupt in fast mode - using normal mode
acd0: CDRW <LITE-ON LTR-24102B/5S07> at ata0-master UDMA33
ad4: 76319MB <SAMSUNG HD080HJ ZH100-33> at ata2-master SATA150
ad6: 78533MB <HDS728080PLA380 PF2OA69A> at ata3-master SATA150
Waiting 5 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 12 lun 0
sa0: <HP C5683A C305> Removable Sequential Access SCSI-3 device
sa0: 40.000MB/s transfers (20.000MHz, offset 32, 16bit)
cd0 at ata0 bus 0 target 0 lun 0
cd0: <LITE-ON LTR-24102B 5S07> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present