5-stable kernel hang during boot
Paul Keusemann
pkeusem at isis.visi.com
Tue Nov 8 08:30:43 PST 2005
Hi,
I've got an IBM Intellistation M Pro with dual 600 Mhz PIIIs, an IBM
DNES-309170W (da0 on ahc0) as the root drive and HighPoint RocketRaid 1520
with two WD1600JD drives mirrored as data drives. There is nothing on
ata0 and the CD-ROM drive is the master on ata1. I have been running a
custom kernel (GENERIC with SMP) since installation. The verbose output
from dmesg from the a 5.4 Release kernel (booted from CD-ROM) is attached.
I installed 5.3 Release on this machine a while back and just decided
to try to upgrade to 5.4 Stable. (This is my first attempt at
doing a buildworld upgrade.) I cvsup'ed /usr/src using the stable-supfile
in /usr/share/examples/cvsup. I then followed the instructions in
/usr/src/Makefile to build world, build a new custom kernel and install
the new kernel. Then I attempted to reboot into single user mode. The
boot hangs while processing ata1, right after the following:
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
The really interesting part is that after installing the new kernel,
I can't boot from kernel.old or another backup of my custom kernel.
They both hang in the same way as the new kernel. If I boot off the 5.4
Release CD-ROM, remove the new kernel and rename kernel.old to kernel,
the system comes up just fine.
At this point I guess I'm looking for any help I can get.
Could the fact that there is nothing on ata0 be causing a problem?
I know I can boot the 5.4 Release kernel, would I be better off upgrading
from the install?
I have had no problems with this machine so I can just scratch
the upgrade, but it would be nice to be able to get it up to 5-stable
and eventually 6-stable.
--
Paul Keusemann pkeusem at visi.com
4266 Joppa Court (952) 894-7805
Savage, MN 55378
-------------- next part --------------
SMP: Added CPU 1 (BSP)
SMP: Added CPU 0 (AP)
MPTable: <IBM-PCCO CrossFire MP>
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 1
cpu1 (AP): APIC ID: 0
bios32: Found BIOS32 Service Directory header at 0xc00fd800
bios32: Entry = 0xfd811 (c00fd811) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xd84c
pnpbios: Found PnP BIOS data at 0xc00fde60
pnpbios: Entry = f0000:5bea Rev = 1.0
Other BIOS signatures found:
ioapic0: Assuming intbase of 0
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
ioapic0: intpin 1 bus ISA
ioapic0: intpin 1 trigger: edge
ioapic0: intpin 1 polarity: high
ioapic0: intpin 2 bus ISA
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
ioapic0: intpin 3 bus ISA
ioapic0: intpin 3 trigger: edge
ioapic0: intpin 3 polarity: high
ioapic0: intpin 4 bus ISA
ioapic0: intpin 4 trigger: edge
ioapic0: intpin 4 polarity: high
ioapic0: intpin 5 bus ISA
ioapic0: intpin 5 trigger: edge
ioapic0: intpin 5 polarity: high
ioapic0: intpin 6 bus ISA
ioapic0: intpin 6 trigger: edge
ioapic0: intpin 6 polarity: high
ioapic0: intpin 7 bus ISA
ioapic0: intpin 7 trigger: edge
ioapic0: intpin 7 polarity: high
ioapic0: intpin 8 bus ISA
ioapic0: intpin 8 trigger: edge
ioapic0: intpin 8 polarity: high
ioapic0: intpin 12 bus ISA
ioapic0: intpin 12 trigger: edge
ioapic0: intpin 12 polarity: high
ioapic0: intpin 13 bus ISA
ioapic0: intpin 13 trigger: edge
ioapic0: intpin 13 polarity: high
ioapic0: intpin 15 bus ISA
ioapic0: intpin 15 trigger: edge
ioapic0: intpin 15 polarity: high
ioapic0: Routing SMI -> intpin 23
ioapic0: intpin 18 bus PCI
ioapic0: intpin 18 trigger: level
ioapic0: intpin 18 polarity: low
ioapic0: intpin 19 bus PCI
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: low
ioapic0: intpin 19 bus PCI
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: low
ioapic0: intpin 19 bus PCI
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: low
ioapic0: intpin 17 bus PCI
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: low
ioapic0: intpin 16 bus PCI
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: low
lapic: Routing ExtINT -> LINT0
lapic: LINT0 trigger: edge
lapic: LINT0 polarity: active-high
lapic: Routing NMI -> LINT1
lapic: LINT1 trigger: edge
lapic: LINT1 polarity: active-high
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x01000000 VER: 0x00040011 LDR: 0x02000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
Found $PIR table, 11 entries at 0xc00f1d50
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 2 A 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 3 A 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 3 B 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 4 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 4 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 4 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 4 D 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 5 0 15 A 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 5 0 15 B 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 5 0 15 C 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 5 0 15 D 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 4 0 14 A 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 4 0 14 B 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 4 0 14 C 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 4 0 14 D 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 13 A 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 13 B 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 13 C 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 3 0 13 D 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 16 A 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 16 B 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 16 C 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 2 0 16 D 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 17 A 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 17 B 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 17 C 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 1 0 17 D 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 6 1 0 A 0x60 3 4 5 6 7 9 10 11 12 14 15
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base e4000000, size 26, enabled
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0146, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x88 (34000 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base e3fff000, size 12, enabled
map[14]: type 4, range 32, base 00006c60, size 5, enabled
map[18]: type 1, range 32, base f6f00000, size 20, enabled
pcib0: slot 2 INTA routed to irq 18
found-> vendor=0x8086, dev=0x1229, revid=0x05
bus=0, slot=2, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0103, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=18
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 00007000, size 8, enabled
map[14]: type 1, range 32, base f6efe000, size 12, enabled
pcib0: slot 3 INTA routed to irq 19
found-> vendor=0x9004, dev=0x7895, revid=0x04
bus=0, slot=3, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=19
powerspec 1 supports D0 D3 current D0
map[10]: type 4, range 32, base 00007400, size 8, enabled
map[14]: type 1, range 32, base f6eff000, size 12, enabled
pcib0: slot 3 INTB routed to irq 19
found-> vendor=0x9004, dev=0x7895, revid=0x04
bus=0, slot=3, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=b, irq=19
powerspec 1 supports D0 D3 current D0
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=4, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000fff0, size 4, enabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=4, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000ff00, size 5, enabled
pcib0: slot 4 INTD routed to irq 19
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=4, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x30 (1440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=19
map[90]: type 4, range 32, base 0000fe00, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=4, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 00006c50, size 3, enabled
map[14]: type 4, range 32, base 00006c48, size 2, enabled
map[18]: type 4, range 32, base 00006c58, size 3, enabled
map[1c]: type 4, range 32, base 00006c4c, size 2, enabled
map[20]: type 4, range 32, base 00007800, size 8, enabled
pcib0: slot 17 INTA routed to irq 17
found-> vendor=0x1103, dev=0x0005, revid=0x02
bus=0, slot=17, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0105, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=17
powerspec 2 supports D0 D3 current D0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe4000000-0xe7ffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe4000000
agp0: allocating GATT for aperture of size 64M
pcib1: <MPTable PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xf7000000-0xf7ffffff
pcib1: prefetched decode 0xe8000000-0xf6dfffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base f7000000, size 24, enabled
pcib1: device (null) requested decoded memory range 0xf7000000-0xf7ffffff
map[14]: type 3, range 32, base e8000000, size 27, enabled
pcib1: device (null) requested decoded memory range 0xe8000000-0xefffffff
pcib1: slot 0 INTA routed to irq 16
found-> vendor=0x10de, dev=0x0110, revid=0xb2
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x28 (1200 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=16
powerspec 2 supports D0 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
fxp0: <Intel 82558 Pro/100 Ethernet> port 0x6c60-0x6c7f mem 0xf6f00000-0xf6ffffff,0xe3fff000-0xe3ffffff irq 18 at device 2.0 on pci0
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xe3fff000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 1014 00d7 0005
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:06:29:ee:08:e2
fxp0: [MPSAFE]
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0x7000-0x70ff mem 0xf6efe000-0xf6efefff irq 19 at device 3.0 on pci0
ahc0: Defaulting to MEMIO off
ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x7000
ahc0: Reading SEEPROM...done.
ahc0: Low byte termination Enabled
ahc0: High byte termination Enabled
ahc0: Downloading Sequencer Program... 413 instructions downloaded
ahc0: Features 0x16235, Bugs 0x15, Flags 0x20485560
ahc0: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0x7400-0x74ff mem 0xf6eff000-0xf6efffff irq 19 at device 3.1 on pci0
ahc1: Defaulting to MEMIO off
ahc1: Reserved 0x100 bytes for rid 0x10 type 4 at 0x7400
ahc1: Reading SEEPROM...done.
ahc1: Low byte termination Enabled
ahc1: High byte termination Enabled
ahc1: Downloading Sequencer Program... 413 instructions downloaded
ahc1: Features 0x16235, Bugs 0x15, Flags 0x20485560
ahc1: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel B, SCSI Id=7, 32/253 SCBs
isab0: <PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0xfff0-0xffff,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 4.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfff0
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave: stat=0x00 err=0x04 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xff00-0xff1f irq 19 at device 4.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff00
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piix0: <PIIX Timecounter> port 0xfe00-0xfe0f at device 4.3 on pci0
Timecounter "PIIX" frequency 3579545 Hz quality 0
atapci1: <HighPoint HPT372 UDMA133 controller> port 0x7800-0x78ff,0x6c4c-0x6c4f,0x6c58-0x6c5f,0x6c48-0x6c4b,0x6c50-0x6c57 irq 17 at device 17.0 on pci0
atapci1: Reserved 0x100 bytes for rid 0x20 type 4 at 0x7800
atapci1: [MPSAFE]
ata2: channel #0 on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x6c50
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x6c48
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata3: channel #1 on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x6c58
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x6c4c
ata3: reset tp1 mask=03 ostat0=50 ostat1=00
ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata3-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata3: [MPSAFE]
cpu0 on motherboard
cpu1 on motherboard
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
Trying Read_Port at 203
CSC0100: start dependent (0)
CSC0100: adding dma mask 0x2
CSC0100: adding dma mask 0x9
CSC0100: adding irq mask 0x20
CSC0100: adding io range 0x534-0x537, size=0x4, align=0x4
CSC0100: adding io range 0x388-0x38b, size=0x4, align=0x8
CSC0100: adding io range 0x220-0x22f, size=0x10, align=0x20
CSC0100: start dependent (1)
CSC0100: adding dma mask 0xa
CSC0100: adding dma mask 0xb
CSC0100: adding irq mask 0x9aa0
CSC0100: adding io range 0x534-0xfff, size=0x4, align=0x4
CSC0100: adding io range 0x388-0x38b, size=0x4, align=0x8
CSC0100: adding io range 0x220-0x26f, size=0x10, align=0x20
CSC0100: start dependent (2)
CSC0100: adding dma mask 0xb
CSC0100: adding irq mask 0x9aa0
CSC0100: adding io range 0x534-0xfff, size=0x4, align=0x4
CSC0100: adding io range 0x388-0x3fb, size=0x4, align=0x8
CSC0100: adding io range 0x220-0x30f, size=0x10, align=0x20
CSC0100: end dependent
CSC0110: adding io range 0x120-0xfe7, size=0x8, align=0x8
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
pnpbios: 21 devices, largest 224 bytes
PNP0200: adding io range 0-0x1f, size=0x20, align=0x1
PNP0200: adding io range 0x80-0x8f, size=0x10, align=0x1
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
pnpbios: handle 2 device ID PNP0200 (0002d041)
PNP0100: adding io range 0x40-0x43, size=0x4, align=0x1
PNP0100: adding irq mask 0x1
pnpbios: handle 3 device ID PNP0100 (0001d041)
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0x1
PNP0b00: adding irq mask 0x100
pnpbios: handle 4 device ID PNP0b00 (000bd041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
PNP0303: adding irq mask 0x2
pnpbios: handle 6 device ID PNP0303 (0303d041)
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
PNP0c04: adding irq mask 0x2000
pnpbios: handle 7 device ID PNP0c04 (040cd041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0x1
pnpbios: handle 8 device ID PNP0a03 (030ad041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x2fffffff, size=0x2ff00000
pnpbios: handle 9 device ID PNP0c01 (010cd041)
PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
pnpbios: handle 10 device ID PNP0c01 (010cd041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 11 device ID PNP0f13 (130fd041)
pnpbios: handle 12 device ID PNP0c02 (020cd041)
pnpbios: handle 13 device ID PNP0c02 (020cd041)
PNP0c02: adding fixed io range 0x2e-0x2f, size=0x2, align=0x1
PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
pnpbios: handle 14 device ID PNP0c02 (020cd041)
PNP0c02: adding io range 0x290-0x297, size=0x8, align=0x1
pnpbios: handle 15 device ID PNP0c02 (020cd041)
PNP0c02: adding io range 0xfd00-0xfd3f, size=0x40, align=0x1
PNP0c02: adding io range 0xfe00-0xfe0f, size=0x10, align=0x1
pnpbios: handle 16 device ID PNP0c02 (020cd041)
PNP0700: adding irq mask 0x40
PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0x1
PNP0700: adding dma mask 0x4
pnpbios: handle 17 device ID PNP0700 (0007d041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 18 device ID PNP0501 (0105d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
pnpbios: handle 19 device ID PNP0501 (0105d041)
PNP0401: adding irq mask 0x80
PNP0401: adding io range 0x378-0x37f, size=0x8, align=0
pnpbios: handle 20 device ID PNP0401 (0104d041)
PNP0c01: adding fixed memory32 range 0xccc00-0xccfff, size=0x400
PNP0c01: adding fixed memory32 range 0xd5e00-0xd7fff, size=0x2200
pnpbios: handle 21 device ID PNP0c01 (010cd041)
ahc_isa_probe 6: ioport 0x6c00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xcd800-0xd1fff,0xcd000-0xcd7ff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0045
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ic_type 90 part_id 73
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x2021 0x2031 0x2021 0x2021
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x2021 0x2029 0x2021 0x2021
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
adv1: Invalid baseport of 0x534 specified. Nearest valid baseport is 0x330. Failing probe.
unknown: <WSS/SB> failed to probe at port 0x220-0x22f,0x388-0x38b,0x534-0x537 irq 5 drq 0,1 on isa0
unknown: <Disabled> failed to probe on isa0
unknown: <CTRL> failed to probe at port 0x120-0x127 on isa0
adv1: Invalid baseport of 0x0 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x40 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x70 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100. Failing probe.
unknown: <PNP0800> failed to probe at port 0x61 on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
adv1: Invalid baseport of 0xf0 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0xcf8 specified. Nearest valid baseport is 0x330. Failing probe.
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0f13> at irq 12 on isa0
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0c02> at port 0x4d0-0x4d1,0x2e-0x2f on isa0
adv1: Invalid baseport of 0x290 specified. Nearest valid baseport is 0x330. Failing probe.
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0c02> at port 0xfe00-0xfe0f,0xfd00-0xfd3f on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x378-0x37f on isa0
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 598980737 Hz quality -100
Timecounters tick every 10.000 msec
lo0: bpf attached
ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ata1-master: setting PIO4 on Intel PIIX4 chip
ata1-master: setting UDMA33 on Intel PIIX4 chip
acd0: <CRD-8400B/1.08> CDROM drive at ata1 as master
acd0: read 6875KB/s (6875KB/s), 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked, lock protected
acd0: Medium: no/blank disc
ata2-master: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
ata2-master: setting PIO4 on HighPoint chip
ata2-master: setting UDMA133 on HighPoint chip
ad4: <WDC WD1600JD-22HBB0/08.02D08> ATA-6 disk at ata2-master
ad4: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA133
ata3-master: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
ata3-master: setting PIO4 on HighPoint chip
ata3-master: setting UDMA133 on HighPoint chip
ad6: <WDC WD1600JD-22HBB0/08.02D08> ATA-6 disk at ata3-master
ad6: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B
ad6: 16 secs/int, 1 depth queue, UDMA133
lun 0
magic_0 0x32bc0abc
magic_1 0x00000000
flags 0x40104 40104<READY,SPAN>
total_disks 2
generation 0
width 1
heads 255
sectors 63
cylinders 19457
total_sectors 312581807
interleave 0
reserved 10
offset 10
disk 0: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad4
sectors 312581807
disk 1: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad6
sectors 312581807
ar0: 152627MB <ATA RAID1 array> [19457/255/63] status: READY subdisks:
disk0 READY on ad4 at ata2-master
disk1 READY on ad6 at ata3-master
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
GEOM: new disk ad4
GEOM: new disk ad6
GEOM: new disk ar0
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 32256 length 160039240704 end 160039272959
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad6s1, start 32256 length 160039240704 end 160039272959
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ar0s1, start 32256 length 160039240704 end 160039272959
GEOM: Configure ad4s1c, start 0 length 160039240704 end 160039240703
GEOM: Configure ad4s1e, start 0 length 42949672960 end 42949672959
GEOM: Configure ad4s1f, start 42949672960 length 42949672960 end 85899345919
GEOM: Configure ad4s1g, start 85899345920 length 42949672960 end 128849018879
GEOM: Configure ad4s1h, start 128849018880 length 31190221824 end 160039240703
GEOM: Configure ad6s1c, start 0 length 160039240704 end 160039240703
GEOM: Configure ad6s1e, start 0 length 42949672960 end 42949672959
GEOM: Configure ad6s1f, start 42949672960 length 42949672960 end 85899345919
GEOM: Configure ad6s1g, start 85899345920 length 42949672960 end 128849018879
GEOM: Configure ad6s1h, start 128849018880 length 31190221824 end 160039240703
GEOM: Configure ar0s1c, start 0 length 160039240704 end 160039240703
GEOM: Configure ar0s1e, start 0 length 42949672960 end 42949672959
GEOM: Configure ar0s1f, start 42949672960 length 42949672960 end 85899345919
GEOM: Configure ar0s1g, start 85899345920 length 42949672960 end 128849018879
GEOM: Configure ar0s1h, start 128849018880 length 31190221824 end 160039240703
ahc0: Selection Timeout on A:11. 0 SCBs aborted
ahc1: Selection Timeout on A:0. 0 SCBs aborted
ahc0: Selection Timeout on A:1. 0 SCBs aborted
ahc1: Selection Timeout on A:1. 0 SCBs aborted
ahc0: Selection Timeout on A:2. 0 SCBs aborted
ahc1: Selection Timeout on A:2. 0 SCBs aborted
ahc0: Selection Timeout on A:3. 0 SCBs aborted
ahc1: Selection Timeout on A:3. 0 SCBs aborted
ahc0: Selection Timeout on A:5. 0 SCBs aborted
ahc1: Selection Timeout on A:4. 0 SCBs aborted
ahc0: Selection Timeout on A:6. 0 SCBs aborted
ahc1: Selection Timeout on A:5. 0 SCBs aborted
ahc0: Selection Timeout on A:8. 0 SCBs aborted
ahc1: Selection Timeout on A:11. 0 SCBs aborted
ahc0: Selection Timeout on A:9. 0 SCBs aborted
ahc1: Selection Timeout on A:12. 0 SCBs aborted
ahc0: Selection Timeout on A:10. 0 SCBs aborted
ahc1: Selection Timeout on A:13. 0 SCBs aborted
ahc0: Selection Timeout on A:12. 0 SCBs aborted
ahc1: Selection Timeout on A:14. 0 SCBs aborted
ahc0: Selection Timeout on A:13. 0 SCBs aborted
ahc1: Selection Timeout on A:15. 0 SCBs aborted
ahc0: Selection Timeout on A:14. 0 SCBs aborted
ahc1: Selection Timeout on A:6. 0 SCBs aborted
ahc0: Selection Timeout on A:15. 0 SCBs aborted
(ahc0:A:4:0): Sending WDTR 1
(probe0:ahc0:0:0:0): Retrying Command
(ahc0:A:4:0): Received WDTR 1 filtered to 1
ahc0: target 4 using 16bit transfers
(ahc0:A:4:0): Sending SDTR period c, offset 8
(ahc0:A:4:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 4 synchronous at 20.0MHz, offset = 0x8
ahc1: Selection Timeout on A:8. 0 SCBs aborted
(ahc0:A:4:0): Sending WDTR 1
(ahc0:A:4:0): Received WDTR 1 filtered to 1
ahc0: target 4 using 16bit transfers
(ahc0:A:4:0): Sending SDTR period c, offset 8
(ahc0:A:4:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 4 synchronous at 20.0MHz, offset = 0x8
(ahc0:A:0:0): Sending WDTR 1
(ahc0:A:0:0): Received WDTR 1 filtered to 1
ahc0: target 0 using 16bit transfers
(ahc0:A:0:0): Sending SDTR period c, offset 8
(ahc0:A:0:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 0 synchronous at 20.0MHz, offset = 0x8
ahc1: Selection Timeout on A:9. 0 SCBs aborted
ahc1: Selection Timeout on A:10. 0 SCBs aborted
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <IBM-PSG DNES-309170W !# SAB0> Fixed Direct Access SCSI-3 device
pass0: Serial Number AJH87942
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
pass1 at ahc0 bus 0 target 4 lun 0
pass1: <SEAGATE DAT 9SP40-000 9030> Removable Sequential Access SCSI-3 device
pass1: Serial Number HN000A4
pass1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <SEAGATE DAT 9SP40-000 9030> Removable Sequential Access SCSI-3 device
sa0: Serial Number HN000A4
sa0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
GEOM: new disk da0
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x00000000 VER: 0x00040011 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0
ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0
ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
ioapic0: routing intpin 17 (PCI IRQ 17) to cluster 0
ioapic0: routing intpin 18 (PCI IRQ 18) to cluster 0
ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM-PSG DNES-309170W !# SAB0> Fixed Direct Access SCSI-3 device
da0: Serial Number AJH87942
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8678MB (17774160 512 byte sectors: 255H 63S/T 1106C)
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:17767827
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 32256 length 9097127424 end 9097159679
GEOM: Configure da0s1a, start 0 length 268435456 end 268435455
GEOM: Configure da0s1b, start 268435456 length 536870912 end 805306367
GEOM: Configure da0s1c, start 0 length 9097127424 end 9097127423
GEOM: Configure da0s1e, start 805306368 length 268435456 end 1073741823
GEOM: Configure da0s1f, start 1073741824 length 4294967296 end 5368709119
GEOM: Configure da0s1g, start 5368709120 length 3728418304 end 9097127423
Mounting root from ufs:/dev/da0s1a
start_init: trying /sbin/init
More information about the freebsd-stable
mailing list