discarded oversize frames
Jonathan Pater
pater at slashdot.org
Fri Feb 25 15:00:33 GMT 2005
I installed 5.3-STABLE a couple weeks back onto what is to become an
office mail server, and after cvsupping to RELENG_5, I began to notice
the following in dmesg:
vr0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
It happens several times after booting, and then about once a minute
after that. At first I suspected the network card itself, so I added an
eepro100 that's always worked fine for me, and then got:
fxp0: discard oversize frame (ether type 800 flags 3 len 1515 > max
1514)
after I had rebooted. Yesterday I cvsupped again (to 5.4-PRERELEASE) and
the warnings still persisted. It doesn't noticeably impact stability or
performance, but it does fill up dmesg rather quickly, and makes the
nightly status emails rather large. Is this something I should be
worried about, or is it indicative of something else faulty in the local
network setup?
I've attached output from dmesg and pciconf, the kernel config is
GENERIC. Please forgive the "eth0" device name, as I have to migrate
several Linux users and it's easier for me to change the interface name
than peruse everyone's homedirs and update their scripts. :)
best,
--
Jonathan "CowboyNeal" Pater | pater at slashdot.org
http://cowboyneal.org/ | http://slashdot.org/
"Don't worry about the world coming to an end today. It's already
tomorrow in Australia." -- Charles Schultz
-------------- next part --------------
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...2 2 1 1 0 1 1 1 0 0 done
No buffers busy after final sync
Uptime: 4m19s
Waiting (max 60 seconds) for system process `hpt_wt' to stop...done
ukphy0: detached
miibus1: detached
Shutting down ACPI
Rebooting...
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.4-PRERELEASE #0: Thu Feb 24 12:00:24 EST 2005
root at kilowog.blockstackers.com:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <AMIINT VIA_K7 >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 2000+ (1666.74-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x662 Stepping = 2
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0400000<AMIE,DSP,3DNow!>
real memory = 805240832 (767 MB)
avail memory = 778219520 (742 MB)
ioapic0 <Version 0.3> irqs 0-23 on motherboard
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <AMIINT VIA_K7> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 8377 (Apollo KT400/KT400A/KT600) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci0: <display, VGA> at device 8.0 (no driver attached)
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd400-0xd43f mem 0xdfe00000-0xdfefffff,0xdfff7000-0xdfff7fff irq 18 at device 10.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:d0:b7:5d:80:b8
atapci0: <VIA 6420 SATA150 controller> port 0xd800-0xd8ff,0xdc00-0xdc0f,0xe000-0xe003,0xe400-0xe407,0xe800-0xe803,0xec00-0xec07 irq 20 at device 15.0 on pci0
ata2: channel #0 on atapci0
ata3: channel #1 on atapci0
atapci1: <VIA 8237 UDMA133 controller> port 0xfc00-0xfc0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0
ata0: channel #0 on atapci1
ata1: channel #1 on atapci1
uhci0: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 21 at device 16.0 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xc800-0xc81f irq 21 at device 16.1 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xcc00-0xcc1f irq 21 at device 16.2 on pci0
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 21 at device 16.3 on pci0
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 16.4 (no driver attached)
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
pci0: <multimedia, audio> at device 17.5 (no driver attached)
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xbc00-0xbcff mem 0xdfff6d00-0xdfff6dff irq 23 at device 18.0 on pci0
miibus1: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: Ethernet address: 00:50:2c:a6:ac:ed
acpi_button1: <Sleep Button> on acpi0
fdc0: <floppy drive controller> port 0x3f7,0x3f4-0x3f5,0x3f2-0x3f3 irq 6 drq 2 on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
orm0: <ISA Option ROMs> at iomem 0xc9000-0xd8fff,0xc8000-0xc8fff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1666739442 Hz quality 800
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 16 steps (100% to 6.2%), currently 100.0%
ad0: 95396MB <WDC WD1000BB-32CCB0/22.04A22> [193821/16/63] at ata0-master UDMA100
ata1-master: DMA limited to UDMA33, non-ATA66 cable or device
ad2: 114473MB <WDC WD1200JB-00CRA1/17.07W17> [232581/16/63] at ata1-master UDMA33
acd0: CDROM <CD-ROM 50X L/15> at ata1-slave PIO4
Mounting root from ufs:/dev/gvinum/root
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
eth0: discard oversize frame (ether type 800 flags 3 len 1515 > max 1514)
-------------- next part --------------
agp0 at pci0:0:0: class=0x060000 card=0x00001106 chip=0x31891106 rev=0x80 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8377 Apollo KT400/A/600 CPU to PCI Bridge'
class = bridge
subclass = HOST-PCI
pcib1 at pci0:1:0: class=0x060400 card=0x00000080 chip=0xb1981106 rev=0x00 hdr=0x01
vendor = 'VIA Technologies Inc'
device = 'ProSavageDDR P4X600 CPU to AGP Bridge'
class = bridge
subclass = PCI-PCI
none0 at pci0:8:0: class=0x030000 card=0xff03102b chip=0x0520102b rev=0x01 hdr=0x00
vendor = 'Matrox Electronic Systems Ltd.'
device = 'MGA-G200B Eclipse/Calao'
class = display
subclass = VGA
fxp0 at pci0:10:0: class=0x020000 card=0x000c8086 chip=0x12298086 rev=0x08 hdr=0x00
vendor = 'Intel Corporation'
device = '82550/1/7/8/9 EtherExpress PRO/100(B) Ethernet Adapter'
class = network
subclass = ethernet
atapci0 at pci0:15:0: class=0x010400 card=0x31491106 chip=0x31491106 rev=0x80 hdr=0x00
vendor = 'VIA Technologies Inc'
device = '??? SATA RAID Controller'
class = mass storage
subclass = RAID
atapci1 at pci0:15:1: class=0x01018a card=0x05711106 chip=0x05711106 rev=0x06 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxx EIDE Controller (All VIA Chipsets)'
class = mass storage
subclass = ATA
uhci0 at pci0:16:0: class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0x81 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
uhci1 at pci0:16:1: class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0x81 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
uhci2 at pci0:16:2: class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0x81 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
uhci3 at pci0:16:3: class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0x81 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
none1 at pci0:16:4: class=0x0c0320 card=0x31041106 chip=0x31041106 rev=0x86 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT6202 USB 2.0 Enhanced Host Controller'
class = serial bus
subclass = USB
isab0 at pci0:17:0: class=0x060100 card=0x00001106 chip=0x32271106 rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8237 PCI-to-ISA Bridge'
class = bridge
subclass = PCI-ISA
none2 at pci0:17:5: class=0x040100 card=0xa1011019 chip=0x30591106 rev=0x60 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8233/33A/8235/8237 AC97 Enhanced Audio Controller'
class = multimedia
subclass = audio
vr0 at pci0:18:0: class=0x020000 card=0x01021106 chip=0x30651106 rev=0x78 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT6102 Rhine II PCI Fast Ethernet Controller'
class = network
subclass = ethernet
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 187 bytes
Desc: This is a digitally signed message part
Url : http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20050225/df9ce5a1/attachment.bin
More information about the freebsd-stable
mailing list