cdboot troubles; 6.0 kernel hanging
Juergen Lock
nox at jelal.kn-bremen.de
Wed Dec 21 14:44:09 PST 2005
I have this box that apparently no longer likes FreeBSD's cdboot,
it prints something about BOOT/LOADER and then just reboots.
Any ideas how to debug something like that? The box already has
FreeBSD installed (5.3 with some patches), and i tried copying the
6.0 kernel from disc1 and loading it manually at the loader prompt.
It hangs after printing (boot -v):
GEOM: new disk ad0
GEOM: new disk ad4
ad0 is on oboard pata (the board is a via kt400), ad4 is a single disk
on a Promise Fasttrack tx2200 sata controller. I guess i could try
to build a 6.0 kernel with ddb, but what would i be looking for then
to find out why its hanging? I'll append 5.3's boot -v dmesg.
(btw i see a lot more of the
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
lines with the 6.0 kernel than with 5.3...)
Thanx,
Juergen
-------snip----
penalty: 480 480 530 5480 5480 5480 5480 5480 50480 50480100480
pcib0: slot 9 INTA routed to irq 11 via \\_SB_.PCI0.LNKB
found-> vendor=0x105a, dev=0x3571, revid=0x02
bus=0, slot=9, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0230, cachelnsz=1 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D3 current D0
map[10]: type 1, range 32, base e8120000, size 17, enabled
map[14]: type 1, range 32, base e8140000, size 17, enabled
map[18]: type 4, range 32, base 0000a800, size 6, enabled
pcib0: matched entry for 0.10.INTA (src \\_SB_.PCI0.LNKC)
pcib0: possible interrupts: 1 3 4 5 6 7 10 11 12 14 15
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKA (references 12, priority 257160):
interrupts: 10 5 11 12 7 6 4 3 15 14 1
penalty: 960 1010 1080 5960 5960 5960 5960 5960 50960 50960100960
\\_SB_.PCI0.LNKC (references 12, priority 257160):
interrupts: 10 5 11 12 7 6 4 3 15 14 1
penalty: 960 1010 1080 5960 5960 5960 5960 5960 50960 50960100960
\\_SB_.PCI0.LNKD (references 12, priority 257160):
interrupts: 10 5 11 12 7 6 4 3 15 14 1
penalty: 960 1010 1080 5960 5960 5960 5960 5960 50960 50960100960
pcib0: slot 10 INTA routed to irq 10 via \\_SB_.PCI0.LNKC
found-> vendor=0x8086, dev=0x1076, revid=0x00
bus=0, slot=10, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 4, range 32, base 0000ac00, size 8, enabled
map[14]: type 1, range 32, base e8181000, size 8, enabled
map[18]: type 1, range 32, base e8182000, size 12, enabled
pcib0: matched entry for 0.11.INTA (src \\_SB_.PCI0.LNKD)
pcib0: possible interrupts: 1 3 4 5 6 7 10 11 12 14 15
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKA (references 12, priority 263050):
interrupts: 5 11 10 12 7 6 4 3 15 14 1
penalty: 1490 1560 1560 6440 6440 6440 6440 6440 51440 51440101440
\\_SB_.PCI0.LNKD (references 12, priority 263050):
interrupts: 5 11 10 12 7 6 4 3 15 14 1
penalty: 1490 1560 1560 6440 6440 6440 6440 6440 51440 51440101440
pcib0: slot 11 INTA routed to irq 11 via \\_SB_.PCI0.LNKD
found-> vendor=0x1000, dev=0x000f, revid=0x26
bus=0, slot=11, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
powerspec 1 supports D0 D3 current D0
pci0:12:0: Transition from D2 to D0
map[10]: type 4, range 32, base 0000b000, size 6, enabled
pcib0: matched entry for 0.12.INTA (src \\_SB_.PCI0.LNKA)
pcib0: possible interrupts: 1 3 4 5 6 7 10 11 12 14 15
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKA (references 12, priority 268941):
interrupts: 5 10 11 12 7 6 4 3 15 14 1
penalty: 1970 2040 2160 6920 6920 6920 6920 6920 51920 51920101920
pcib0: slot 12 INTA routed to irq 10 via \\_SB_.PCI0.LNKA
found-> vendor=0x1274, dev=0x1371, revid=0x08
bus=0, slot=12, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0105, statreg=0x0410, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x80 (32000 ns)
intpin=a, irq=10
powerspec 1 supports D0 D2 D3 current D0
map[20]: type 4, range 32, base 0000b400, size 5, enabled
pcib0: matched entry for 0.16.INTA (src \\_SB_.PCI0.LNKA)
pcib0: slot 16 INTA is already routed to irq 10
found-> vendor=0x1106, dev=0x3038, revid=0x80
bus=0, slot=16, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000b800, size 5, enabled
pcib0: matched entry for 0.16.INTB (src \\_SB_.PCI0.LNKB)
pcib0: slot 16 INTB is already routed to irq 11
found-> vendor=0x1106, dev=0x3038, revid=0x80
bus=0, slot=16, func=1
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000bc00, size 5, enabled
pcib0: matched entry for 0.16.INTC (src \\_SB_.PCI0.LNKC)
pcib0: slot 16 INTC is already routed to irq 10
found-> vendor=0x1106, dev=0x3038, revid=0x80
bus=0, slot=16, func=2
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base e8183000, size 8, enabled
pcib0: matched entry for 0.16.INTD (src \\_SB_.PCI0.LNKD)
pcib0: slot 16 INTD is already routed to irq 11
found-> vendor=0x1106, dev=0x3104, revid=0x82
bus=0, slot=16, func=3
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x1106, dev=0x3177, revid=0x00
bus=0, slot=17, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000c000, size 4, enabled
found-> vendor=0x1106, dev=0x0571, revid=0x06
bus=0, slot=17, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000c400, size 8, enabled
pcib0: matched entry for 0.17.INTC (src \\_SB_.PCI0.LNKC)
pcib0: slot 17 INTC is already routed to irq 10
found-> vendor=0x1106, dev=0x3059, revid=0x50
bus=0, slot=17, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000c800, size 8, enabled
map[14]: type 1, range 32, base e8184000, size 8, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.PCI0.LNKA)
pcib0: slot 18 INTA is already routed to irq 10
found-> vendor=0x1106, dev=0x3065, revid=0x74
bus=0, slot=18, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
agp0: <VIA 8377 (Apollo KT400/KT400A/KT600) host to PCI bridge> mem 0xd0000000-0xd7ffffff at device 0.0 on pci0
agp0: Reserved 0x8000000 bytes for rid 0x10 type 3 at 0xd0000000
agp0: allocating GATT for aperture of size 256M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x9000-0x9fff
pcib1: memory decode 0xe8000000-0xe80fffff
pcib1: prefetched decode 0xd8000000-0xe7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 3, range 32, base d8000000, size 27, enabled
pcib1: device (null) requested decoded memory range 0xd8000000-0xdfffffff
map[14]: type 4, range 32, base 00009000, size 8, enabled
pcib1: device (null) requested decoded I/O range 0x9000-0x90ff
map[18]: type 1, range 32, base e8020000, size 16, enabled
pcib1: device (null) requested decoded memory range 0xe8020000-0xe802ffff
pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.LNKA)
pcib0: slot 1 INTA is already routed to irq 10
pcib1: slot 0 INTA is routed to irq 10
found-> vendor=0x1002, dev=0x4144, revid=0x00
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base e0000000, size 27, memory disabled
pcib1: device (null) requested decoded memory range 0xe0000000-0xe7ffffff
map[14]: type 1, range 32, base e8030000, size 16, enabled
pcib1: device (null) requested decoded memory range 0xe8030000-0xe803ffff
found-> vendor=0x1002, dev=0x4164, revid=0x00
bus=1, slot=0, func=1
class=03-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0080, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
pci1: <display> at device 0.1 (no driver attached)
atapci0: <Promise PDC20571 SATA150 controller> port 0xa400-0xa4ff,0xa000-0xa07f mem 0xe8100000-0xe811ffff,0xe8180000-0xe8180fff irq 11 at device 9.0 on pci0
atapci0: failed: rid 0x20 is memory, requested 4
atapci0: Reserved 0x20000 bytes for rid 0x20 type 3 at 0xe8100000
atapci0: Reserved 0x1000 bytes for rid 0x1c type 3 at 0xe8180000
atapci0: [MPSAFE]
ata2: channel #0 on atapci0
ata2: reset tp1 mask=01 ostat0=50 ostat1=50
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata3: channel #1 on atapci0
ata3: reset tp1 mask=00 ostat0=ff ostat1=ff
ata3: [MPSAFE]
ata4: channel #2 on atapci0
ata4: reset tp1 mask=03 ostat0=a0 ostat1=b0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-master: stat=0xa0 err=0xa0 lsb=0xa0 msb=0xa0
ata4-slave: stat=0xb0 err=0xb0 lsb=0xb0 msb=0xb0
ata4: reset tp2 stat0=a0 stat1=b0 devices=0x0
ata4: [MPSAFE]
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port 0xa800-0xa83f mem 0xe8140000-0xe815ffff,0xe8120000-0xe813ffff irq 10 at device 10.0 on pci0
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xe8120000
em0: Reserved 0x40 bytes for rid 0x18 type 4 at 0xa800
em0: [GIANT-LOCKED]
em0: bpf attached
em0: Ethernet address: 00:0e:0c:6d:38:a9
em0: Speed:N/A Duplex:N/A
sym0: <875> port 0xac00-0xacff mem 0xe8182000-0xe8182fff,0xe8181000-0xe81810ff irq 11 at device 11.0 on pci0
sym0: Reserved 0x100 bytes for rid 0x14 type 3 at 0xe8181000
sym0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xe8182000
sym0: chip clock is 40401KHz
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: [GIANT-LOCKED]
pci0: <multimedia, audio> at device 12.0 (no driver attached)
uhci0: <VIA 83C572 USB controller> port 0xb400-0xb41f irq 10 at device 16.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xb400
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xb800-0xb81f irq 11 at device 16.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xb800
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xbc00-0xbc1f irq 10 at device 16.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbc00
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xe8183000-0xe81830ff irq 11 at device 16.3 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xe8183000
ehci0: [GIANT-LOCKED]
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <VIA VT6202 USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <VIA 8235 UDMA133 controller> port 0xc000-0xc00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 17.1 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xc000
ata0: channel #0 on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: [MPSAFE]
pci0: <multimedia, audio> at device 17.5 (no driver attached)
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xc800-0xc8ff mem 0xe8184000-0xe81840ff irq 10 at device 18.0 on pci0
vr0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xc800
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x004063, model 0x0032, rev. 5
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: bpf attached
vr0: Ethernet address: 00:0a:e6:55:d5:db
vr0: [GIANT-LOCKED]
fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 10: ioport 0xac00 alloc failed
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xe2000-0xe2fff,0xc0000-0xccfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 2075027952 Hz quality 800
Timecounters tick every 1.000 msec
i4bipr: 4 IP over raw HDLC ISDN device(s) attached (VJ header compression)
ipr0: bpf attached
ipr1: bpf attached
ipr2: bpf attached
ipr3: bpf attached
i4bctl: ISDN system control port attached
i4b: ISDN call control device attached
i4brbch: 4 raw B channel access device(s) attached
i4btel: 2 ISDN telephony interface device(s) attached
i4btrc: 4 ISDN trace device(s) attached
lo0: bpf attached
cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0%
ata0-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
ata0-master: setting PIO4 on VIA 8235 chip
ata0-master: setting UDMA133 on VIA 8235 chip
ad0: <Maxtor 6Y080L0/YAR41VW0> ATA-7 disk at ata0-master
ad0: 78167MB (160086528 sectors), 158816 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA133
ar: FreeBSD check1 failed
ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ata1-master: setting PIO4 on VIA 8235 chip
ata1-master: setting UDMA33 on VIA 8235 chip
ata1-slave: setting PIO4 on VIA 8235 chip
ata1-slave: setting UDMA33 on VIA 8235 chip
acd0: <NEC DV-5800C/D9S2> DVDROM drive at ata1 as master
acd0: read 8268KB/s (8268KB/s), 512KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
acd1: <HL-DT-ST DVDRAM GSA-4120B/A102> DVDR drive at ata1 as slave
acd1: read 6890KB/s (6890KB/s) write 6890KB/s (6890KB/s), 2048KB buffer, UDMA33
acd1: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd1: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd1: Audio: play, 256 volume levels
acd1: Mechanism: ejectable tray, unlocked
acd1: Medium: no/blank disc
ata2-master: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
ad4: <ST3160827AS/3.42> ATA-6 disk at ata2-master
ad4: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, SATA150
ar: Promise check1 failed
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
GEOM: new disk ad0
GEOM: new disk ad4
[0] f:00 typ:12 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:33559722
[1] f:80 typ:12 s(CHS):1023/255/63 e(CHS):1023/254/63 s:33559785 l:66974985
[2] f:00 typ:5 s(CHS):1023/255/63 e(CHS):1023/254/63 s:100534770 l:33993540
[3] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:134528310 l:25543350
GEOM: Configure ad0s1, start 32256 length 17182577664 end 17182609919
GEOM: Configure ad0s2, start 17182609920 length 34291192320 end 51473802239
GEOM: Configure ad0s3, start 51473802240 length 17404692480 end 68878494719
GEOM: Configure ad0s4, start 68878494720 length 13078195200 end 81956689919
[0] f:00 typ:5 s(CHS):1023/255/63 e(CHS):1023/254/63 s:248573745 l:64002960
[1] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:248573682
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 127269757440 length 32769515520 end 160039272959
GEOM: Configure ad4s2, start 32256 length 127269725184 end 127269757439
MBREXT Slice 5 on ad0s3:
[0] f:00 typ:131 s(CHS):1023/254/63 e(CHS):1023/254/63 s:63 l:32001417
[1] f:00 typ:5 s(CHS):1023/254/63 e(CHS):1023/254/63 s:32001480 l:1992060
GEOM: Configure ad0s5, start 32256 length 16384725504 end 16384757759
MBREXT Slice 6 on ad0s3:
[0] f:00 typ:130 s(CHS):1023/254/63 e(CHS):1023/254/63 s:63 l:1991997
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s6, start 16384790016 length 1019902464 end 17404692479
GEOM: Configure ad0s4a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s4b, start 268435456 length 1073741824 end 1342177279
GEOM: Configure ad0s4c, start 0 length 13078195200 end 13078195199
GEOM: Configure ad0s4e, start 1342177280 length 10737418240 end 12079595519
GEOM: Configure ad0s4f, start 12079595520 length 998599680 end 13078195199
MBREXT Slice 5 on ad4s1:
[0] f:00 typ:12 s(CHS):1023/254/63 e(CHS):1023/254/63 s:63 l:64002897
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s5, start 32256 length 32769483264 end 32769515519
GEOM: Configure ad4s2a, start 0 length 268435456 end 268435455
GEOM: Configure ad4s2b, start 268435456 length 1073741824 end 1342177279
GEOM: Configure ad4s2c, start 0 length 127269725184 end 127269725183
GEOM: Configure ad4s2d, start 1342177280 length 125927547904 end 127269725183
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe4:ata2:0:0:0): error 22
(probe4:ata2:0:0:0): Unretryable Error
(probe5:ata2:0:1:0): error 22
(probe5:ata2:0:1:0): Unretryable Error
(probe6:ata3:0:0:0): error 22
(probe6:ata3:0:0:0): Unretryable Error
(probe7:ata3:0:1:0): error 22
(probe7:ata3:0:1:0): Unretryable Error
(probe8:ata4:0:0:0): error 22
(probe8:ata4:0:0:0): Unretryable Error
(probe9:ata4:0:1:0): error 22
(probe9:ata4:0:1:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe4:ata2:0:0:0): error 22
(probe4:ata2:0:0:0): Unretryable Error
(probe5:ata2:0:1:0): error 22
(probe5:ata2:0:1:0): Unretryable Error
(probe6:ata3:0:0:0): error 22
(probe6:ata3:0:0:0): Unretryable Error
(probe7:ata3:0:1:0): error 22
(probe7:ata3:0:1:0): Unretryable Error
(probe8:ata4:0:0:0): error 22
(probe8:ata4:0:0:0): Unretryable Error
(probe9:ata4:0:1:0): error 22
(probe9:ata4:0:1:0): Unretryable Error
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe2:ata1:0:0:0): error 6
(probe2:ata1:0:0:0): Unretryable Error
(probe3:ata1:0:1:0): error 6
(probe3:ata1:0:1:0): Unretryable Error
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe10:sym0:0:0:0): Retrying Command
(probe10:sym0:0:0:0): Retrying Command
(probe0:sym0:0:0:1): Device Busy
(probe0:sym0:0:0:1): Retrying Command
pass0 at sym0 bus 0 target 0 lun 0
pass0: <IBM DNES-309170 SA30> Fixed Direct Access SCSI-3 device
pass0: Serial Number AJ156082
pass0: 20.000MB/s transfers (20.000MHz, offset 16), Tagged Queueing Enabled
pass1 at ata1 bus 0 target 0 lun 0
pass1: <_NEC DV-5800C D9S2> Removable CD-ROM SCSI-0 device
pass1: 33.000MB/s transfers
pass2 at ata1 bus 0 target 1 lun 0
pass2: <HL-DT-ST DVDRAM GSA-4120B A102> Removable CD-ROM SCSI-0 device
pass2: 33.000MB/s transfers
GEOM: new disk cd0
GEOM: new disk cd1
GEOM: new disk da0
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <_NEC DV-5800C D9S2> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
(cd1:ata1:0:1:0): error 6
(cd1:ata1:0:1:0): Unretryable Error
cd1 at ata1 bus 0 target 1 lun 0
cd1: <HL-DT-ST DVDRAM GSA-4120B A102> Removable CD-ROM SCSI-0 device
cd1: 33.000MB/s transfers
cd1: Attempt to query device size failed: NOT READY, Medium not present
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd1:ata1:0:1:0): error 6
(cd1:ata1:0:1:0): Unretryable Error
(cd1:ata1:0:1:0): error 6
(cd1:ata1:0:1:0): Unretryable Error
(cd1:ata1:0:1:0): error 6
(cd1:ata1:0:1:0): Unretryable Error
da0 at sym0 bus 0 target 0 lun 0
da0: <IBM DNES-309170 SA30> Fixed Direct Access SCSI-3 device
da0: Serial Number AJ156082
da0: 20.000MB/s transfers (20.000MHz, offset 16), Tagged Queueing Enabled
da0: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C)
[0] f:00 typ:5 s(CHS):0/0/33 e(CHS):373/133/16 s:32 l:6000608
[1] f:80 typ:165 s(CHS):373/133/17 e(CHS):1023/54/27 s:6000640 l:11915264
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 16384 length 3072311296 end 3072327679
GEOM: Configure da0s2, start 3072327680 length 6100615168 end 9172942847
MBREXT Slice 5 on da0s1:
[0] f:80 typ:131 s(CHS):0/2/1 e(CHS):1023/63/32 s:32 l:6000576
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s5, start 16384 length 3072294912 end 3072311295
GEOM: Configure da0s2a, start 0 length 268435456 end 268435455
GEOM: Configure da0s2c, start 0 length 6100615168 end 6100615167
GEOM: Configure da0s2e, start 268435456 length 5832179712 end 6100615167
Mounting root from ufs:/dev/ad4s2a
start_init: trying /sbin/init
tun0: bpf attached
pflog0: bpf attached
More information about the freebsd-stable
mailing list