panic: vm_fault: fault on nofault entry, addr: d0a5c000
David Scheidt
dscheidt at panix.com
Mon Dec 5 07:10:01 PST 2005
There were messages about rl1 receiving oversized frames just before
the panic. They didn't get recorded, sorry. (Working remotely, no
serial console.)
I've still got the dump. I can do more if required.
Regards,
David
GNU gdb 6.1.1 [FreeBSD]
Copyright 2004 Free Software Foundation, Inc.
GDB is free software, covered by the GNU General Public License, and you are
welcome to change it and/or distribute copies of it under certain conditions.
Type "show copying" to see the conditions.
There is absolutely no warranty for GDB. Type "show warranty" for details.
This GDB was configured as "i386-marcel-freebsd".
Unread portion of the kernel message buffer:
panic: vm_fault: fault on nofault entry, addr: d0a5c000
KDB: enter: panic
panic: from debugger
Uptime: 1d18h30m35s
Dumping 255 MB (2 chunks)
chunk 0: 1MB (159 pages) ... ok
chunk 1: 255MB (65280 pages) 240 224 208 192 176 160 144 128 112 96 80 64 48 32 16
#0 doadump () at pcpu.h:165
165 __asm __volatile("movl %%fs:0,%0" : "=r" (td));
(kgdb) bt
#0 doadump () at pcpu.h:165
#1 0xc0564748 in boot (howto=260) at /usr/src/sys/kern/kern_shutdown.c:399
#2 0xc05649f3 in panic (fmt=0xc076844f "from debugger")
at /usr/src/sys/kern/kern_shutdown.c:555
#3 0xc0457be9 in db_panic (addr=-1067991289, have_addr=0, count=-1,
modif=0xcbfec924 "") at /usr/src/sys/ddb/db_command.c:438
#4 0xc0457b80 in db_command (last_cmdp=0xc0825ee4, cmd_table=0x0,
aux_cmd_tablep=0xc07b02a4, aux_cmd_tablep_end=0xc07b02a8)
at /usr/src/sys/ddb/db_command.c:350
#5 0xc0457c48 in db_command_loop () at /usr/src/sys/ddb/db_command.c:458
#6 0xc045983d in db_trap (type=3, code=0) at /usr/src/sys/ddb/db_main.c:221
#7 0xc057c183 in kdb_trap (type=3, code=0, tf=0xcbfeca64)
at /usr/src/sys/kern/subr_kdb.c:473
#8 0xc0734a5c in trap (frame=
{tf_fs = -872546296, tf_es = -1068040152, tf_ds = -1065877464, tf_edi = 1, tf_esi = -1065735013, tf_ebp = -872494428, tf_isp = -872494448, tf_ebx = -872494384, tf_edx = 0, tf_ecx = -1056878592, tf_eax = 18, tf_trapno = 3, tf_err = 0, tf_eip = -1067991289, tf_cs = 32, tf_eflags = 658, tf_esp = -872494396, tf_ss = -1068086877}) at /usr/src/sys/i386/i386/trap.c:591
#9 0xc07277ea in calltrap () at /usr/src/sys/i386/i386/exception.s:139
#10 0xc057bf07 in kdb_enter (msg=0x12 <Address 0x12 out of bounds>)
at cpufunc.h:60
#11 0xc05649a3 in panic (
fmt=0xc07a2c9b "vm_fault: fault on nofault entry, addr: %lx")
at /usr/src/sys/kern/kern_shutdown.c:539
#12 0xc06d61ec in vm_fault (map=0xc1043000, vaddr=3500523520,
fault_type=1 '\001', fault_flags=0) at /usr/src/sys/vm/vm_fault.c:277
#13 0xc0734c4f in trap_pfault (frame=0xcbfecc0c, usermode=0, eva=3500523520)
at /usr/src/sys/i386/i386/trap.c:731
#14 0xc07348e9 in trap (frame=
{tf_fs = -1068171256, tf_es = -1049034712, tf_ds = 40, tf_edi = -1048979612, tf_esi = -794443778, tf_ebp = -872493928, tf_isp = -872494024, tf_ebx = -1049118720, tf_edx = -1048979456, tf_ecx = 39, tf_eax = -254535834, tf_trapno = 12, tf_err = 0, tf_eip = -1066193906, tf_cs = 32, tf_eflags = 66054, tf_esp = 10896, tf_ss = 2048}) at /usr/src/sys/i386/i386/trap.c:432
#15 0xc07277ea in calltrap () at /usr/src/sys/i386/i386/exception.s:139
#16 0xc0732c0e in generic_bcopy () at /usr/src/sys/i386/i386/support.s:489
(kgdb) quit
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files.
# If you are in doubt as to the purpose or necessity of a line, check first
# in NOTES.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.422 2005/01/05 05:25:21 kuriyama Exp $
machine i386
cpu I586_CPU
cpu I686_CPU
ident TOR
# To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" # Default places to look for devices.
makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols
#options SCHED_ULE # ULE scheduler
options SCHED_4BSD # 4BSD scheduler
options PREEMPTION # Enable kernel thread preemption
options INET # InterNETworking
options INET6 # IPv6 communications protocols
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates support
options UFS_ACL # Support for access control lists
options UFS_DIRHASH # Improve performance on big directories
options MD_ROOT # MD is a potential root device
options NFSCLIENT # Network Filesystem Client
options NFSSERVER # Network Filesystem Server
options NFS_ROOT # NFS usable as /, requires NFSCLIENT
options MSDOSFS # MSDOS Filesystem
options CD9660 # ISO 9660 Filesystem
options PROCFS # Process filesystem (requires PSEUDOFS)
options PSEUDOFS # Pseudo-filesystem framework
options GEOM_GPT # GUID Partition Tables.
options COMPAT_43 # Compatible with BSD 4.3 [KEEP THIS!]
options COMPAT_FREEBSD4 # Compatible with FreeBSD4
options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI
options KTRACE # ktrace(1) support
options SYSVSHM # SYSV-style shared memory
options SYSVMSG # SYSV-style message queues
options SYSVSEM # SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
options ADAPTIVE_GIANT # Giant mutex is adaptive.
options IPSEC
options IPSEC_ESP
# Debugging for use in -current
options KDB # Enable kernel debugger support.
options DDB # Support DDB.
options GDB # Support remote GDB.
options INVARIANTS # Enable calls of extra sanity checking
options INVARIANT_SUPPORT # Extra sanity checks of internal structures, required by INVARIANTS
#options WITNESS # Enable checks to detect deadlocks and cycles
options WITNESS_SKIPSPIN # Don't run witness on spinlocks for speed
# To make an SMP kernel, the next two lines are needed
#options SMP # Symmetric MultiProcessor Kernel
#device apic # I/O APIC
# Bus support. Do not remove isa, even if you have no isa slots
device isa
device eisa
device pci
# Floppy drives
device fdc
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device ataraid # ATA RAID drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID # Static device numbering
# SCSI Controllers
# SCSI peripherals
device scbus # SCSI bus (required for SCSI)
device ch # SCSI media changers
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
device ses # SCSI Environmental Services (and SAF-TE)
# RAID controllers interfaced to the SCSI subsystem
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
device vga # VGA video card driver
device splash # Splash screen and screen saver support
# syscons is the default console driver, resembling an SCO console
device sc
# Enable this for the pcvt (VT220 compatible) console driver
#device vt
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
device agp # support several AGP chipsets
# Floating point support - do not disable.
device npx
# Power management support (see NOTES for more options)
#device apm
# Add suspend/resume support for the i8254.
device pmtimer
# PCCARD (PCMCIA) support
# PCMCIA and cardbus bridge support
device cbb # cardbus (yenta) bridge
device pccard # PC Card (16-bit) bus
device cardbus # CardBus (32-bit) bus
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# If you've got a "dumb" serial or parallel PCI card that is
# supported by the puc(4) glue driver, uncomment the following
# line to enable it (connects to the sio and/or ppc drivers):
#device puc
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device em # Intel PRO/1000 adapter Gigabit Ethernet Card
device ixgb # Intel PRO/10GbE Ethernet Card
device txp # 3Com 3cR990 (``Typhoon'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device bfe # Broadcom BCM440x 10/100 Ethernet
device bge # Broadcom BCM570xx Gigabit Ethernet
device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device lge # Level 1 LXT1001 gigabit Ethernet
device nge # NatSemi DP83820 gigabit Ethernet
device pcn # AMD Am79C97x PCI 10/100 (precedence over 'lnc')
device re # RealTek 8139C+/8169/8169S/8110S
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS 7016
device sk # SysKonnect SK-984x & SK-982x gigabit Ethernet
device ste # Sundance ST201 (D-Link DFE-550TX)
device ti # Alteon Networks Tigon I/II gigabit Ethernet
device tl # Texas Instruments ThunderLAN
device tx # SMC EtherPower II (83c170 ``EPIC'')
device vge # VIA VT612x gigabit Ethernet
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs. pccard NICs included.
# 'device ed' requires 'device miibus'
# Wireless NIC cards
device wlan # 802.11 support
device ath_hal
device ath
device ath_rate_onoe
device an # Aironet 4500/4800 802.11 wireless NICs.
device awi # BayStack 660 and others
device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs.
#device wl # Older non 802.11 Wavelan wireless NIC.
# Pseudo devices.
device loop # Network loopback
device mem # Memory and kernel memory devices
device io # I/O device
device random # Entropy device
device ether # Ethernet support
device sl # Kernel SLIP
device ppp # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
device gif # IPv6 and IPv4 tunneling
device faith # IPv6-to-IPv4 relaying (translation)
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
device bpf # Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
#device udbp # USB Double Bulk Pipe devices
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device urio # Diamond Rio 500 MP3 player
device uscanner # Scanners
# USB Ethernet, requires miibus
device aue # ADMtek USB Ethernet
device axe # ASIX Electronics USB Ethernet
device cue # CATC USB Ethernet
device kue # Kawasaki LSI USB Ethernet
device rue # RealTek RTL8150 USB Ethernet
# FireWire support
device firewire # FireWire bus code
device sbp # SCSI over FireWire (Requires scbus and da)
device fwe # Ethernet over FireWire (non-standard!)
More information about the freebsd-stable
mailing list